2004 MAZDA MODEL RX 8 automatic transmission

5-15
Driving Your Mazda
Starting and Driving
Form No. 8R65-EA-03C
Shifting specification
Shifting up
If the vehicle speed is lower than the
speed specified for each gear, the gear
cannot be shifted up to a higher gear.
Shifting down
If the vehicle speed is higher than the
speed specified for each gear, the gear
cannot be shifted down to a lower gear.
During deceleration, the gears shift down
automatically when speed is reduced to
the following:
If the vehicle is kicked down at the
following speeds or lower, the gears shift
down automatically:Recommendations for shiftingUpshifting
For normal acceleration and cruising, we
recommend these shift points.
Downshifting
When you must slow down in heavy
traffic or on a steep upgrade
, downshift
before the engine starts to overwork. This
gives better acceleration when you need
more speed.
On a steep downgrade
, downshifting
helps maintain safe speed and prolongs
brake life.

Driving Tips
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transmission
will shift to a lower gear, depending on
vehicle speed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release all brakes while gradually
accelerating.
Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight
and grade steepness. Descend slowly,
using the brakes only occasionally to
prevent them from overheating.
Gear Vehicle speed
M1→
M2You can shift up to M2
whether the vehicle is
stopped or moving.
M2→
M3 20 km/h (12 mph)
M3→
M4 20 km/h (12 mph)
Gear Vehicle speed
M4→
M3 163 km/h (101 mph)
M3→
M2 112 km/h (70 mph)
M2→
M1 45 km/h (28 mph)
Gear Vehicle speed
M4→
M3 31 km/h (19 mph)
M3 or M2→
M1 8 km/h (5 mph)
NOTE
If the vehicle is driven at a low speed
from a standing start while in M2, the
gear may not shift down to M1
automatically.
Gear Vehicle speed
M4→
M3 149 km/h (93 mph)
M4→
M2 56 km/h (35 mph)
M3→
M2 56 km/h (35 mph)
M1 to M2 24 km/h (15 mph)
M2 to M3 40 km/h (25 mph)
M3 to M4 65 km/h (40 mph)
J60E_8R65-EA-03C_Edition2.book Page 15 Saturday, April 26, 2003 1:48 PM

5-20
Driving Your Mazda
Starting and Driving
Form No. 8R65-EA-03C

To Cancel
To turn off the system, use one
of these
methods:
•Press the ON/OFF switch.
•Slightly depress the brake pedal.
•Depress the clutch pedal. (Manual
transmission only)
•Press the CANCEL button.
The system is off when the ignition is off.The Traction Control System (TCS)
enhances traction and safety by regulating
engine torque and breaking. When the
TCS detects driving wheel slippage, it
lowers engine torque and operates the
brakes to prevent loss of traction.
This means that on a slick surface, the
engine adjusts automatically to provide
optimum power to the drive wheels
without causing them to spin and lose
traction.
NOTE
Cruise control will cancel at about
15 km/h (9 mph) below the preset
speed or below 30 km/h (19 mph).
Traction Control System
(TCS)*
TCS and Unsafe Driving:
The traction control system (TCS)
cannot compensate for unsafe and
reckless driving, excessive speed,
tailgating (following another vehicle
too closely), and hydroplaning
(reduced tire friction and road
contact because of water on the road
surface). You can still have an
accident. So don’t rely on the traction
control system as a substitute for safe
driving.
TCS and Snow and Ice:
Driving without proper traction
devices on snow and ice-covered
roads is dangerous. The traction
control system (TCS) alone cannot
provide adequate traction and you
could still have an accident. Use snow
tires or tire chains and drive at
reduced speeds when roads are
covered with ice and snow.
WARNING
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 20 Saturday, April 26, 2003 1:48 PM

5-31
Driving Your Mazda
Instrument Cluster and Indicators
Form No. 8R65-EA-03C
Odometer
The odometer records the total distance
the vehicle has been driven.
Tr i p m e t e r
The trip meter can record the total
distance of two trips. One is recorded in
trip meter A, and the other is recorded in
trip meter B.
For instance, trip meter A can record the
distance from the point of origin, and trip
meter B can record the distance from
where the fuel tank is filled.
When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.
When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.The trip meter records the total
distance the vehicle is driven until the
meter is again reset. Return it to "0.0"
by holding the selector depressed for
more than 1 second. Use this meter to
measure trip distances and to compute
fuel consumption.
Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute
(rpm).
NOTE
When the ignition switch is in the ACC
or LOCK position, the odometer or trip
meters cannot be displayed, however,
pressing the selector button can
inadvertently switch the trip meters or
reset them during an approximate ten-
minute period in the following cases:
•After the ignition switch is turned to
the ACC or LOCK position from
the ON position.
•After any door is opened.
NOTE
•Only the trip meters record tenths of
kilometers (miles).
•The trip record will be erased when:
The power supply is interrupted
(blown fuse or the battery is
disconnected).
The vehicle is driven over
999.9 km (mile).
Red zone Striped zone
Automatic
transmission
J60E_8R65-EA-03C_Edition2.book Page 31 Saturday, April 26, 2003 1:48 PM

5-36
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C
Signal Warning/Indicator Lights Page
Low Fuel Warning Light 5-41
Seat Belt Warning Light 5-41
Door-Ajar Warning Light 5-41
Low Washer Fluid Level Warning Light 5-41
Automatic Transmission Warning Light 5-42
Tire Pressure Monitoring System Warning Light 5-42
Security Indicator Light 5-43
Headlight High-Beam Indicator Light 5-43
Shift Position Indicator Light 5-44
TCS/DSC Indicator Light 5-44
DSC OFF Indicator Light 5-44
Cruise Main Indicator Light 5-45
Cruise Set Indicator Light 5-45
Light-On Indicator Light 5-45
Power Steering Malfunction Indicator Light 5-45
Headlight Auto-Leveling Malfunction Indicator Light 5-46
Turn-Signal/Hazard Warning Indicator Lights 5-46
J60E_8R65-EA-03C_Edition2.book Page 36 Saturday, April 26, 2003 1:48 PM

5-42
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Automatic Transmission
Wa r n i n g L i g h t
This warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
The light illuminates when the
transmission has a problem.

Tire Pressure Monitoring System
Warning Light*
This warning light illuminates for a few
seconds when the ignition switch is turned
to the ON position.
Thereafter, the warning light illuminates
when tire pressure is too low or too high
in one or more tires, and flashes when
there is a system malfunction.Warning light illuminates/Warning
beep sounds
When the warning light illuminates, and
the warning beep sounds (about 3
seconds), tire pressure is too low or too
high in one or more tires.
Adjust the tire pressure to the correct tire
pressure at an Authorized Mazda Dealer
or the nearest service station. Refer to the
specification charts (page 10-7). If the automatic transmission warning
light illuminates, the transmission has
an electrical problem. Continuing to
drive your Mazda in this condition
could cause damage to your
transmission. Consult an Authorized
Mazda Dealer as soon as possible.
CAUTION
Vehicle Handling When Tire Pressure
Monitoring System Warning Light
Illuminates/Flashes:
When the tire pressure monitoring
system warning light illuminates or
flashes, or the tire pressure warning
beep sounds, it is dangerous to drive
the vehicle at high speeds, or perform
sudden maneuvering or braking.
Vehicle drivability could worsen and
result in an accident.
When the tire pressure monitoring
system warning light illuminates or
flashes, or the tire pressure warning
beep sounds, decrease vehicle speed
immediately and avoid sudden
maneuvering and braking. Have the
system and tires checked or perform
the appropriate repair as soon as
possible.
Ignoring the Warning Light:
Ignoring the warning light is
dangerous, even if you know why it is
illuminated. Have the problem taken
care of as soon as possible before it
develops into a more serious situation
that could lead to tire failure and a
dangerous accident.
WARNING
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 42 Saturday, April 26, 2003 1:48 PM

5-44
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R65-EA-03C

Shift Position Indicator Light
(Automatic Transmission)
This indicates the selected shift position
when the ignition switch is in the ON
position.
In manual mode, the "M" of the shift
position indicator illuminates and the
numeral for the selected gear illuminates
in the gear position indicator.

TCS/DSC Indicator Light*
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position. If the TCS or DSC is
operating, the indicator light flashes.
If the light stays on, the TCS or DSC may
have a malfunction and they may not
operate correctly. Take your vehicle to an
Authorized Mazda Dealer.

DSC OFF Indicator Light*
This indicator light stays on for a few
seconds when the ignition switch is turned
to the ON position.
It also comes on when the DSC OFF
switch is pressed and TCS/DSC is
switched off.
If the light stays on when the TCS/DSC is
not switched off, take your vehicle to an
Authorized Mazda Dealer. The dynamic
stability control may have a malfunction.
Gear position indicator
*Some models.
J60E_8R65-EA-03C_Edition2.book Page 44 Saturday, April 26, 2003 1:48 PM

7-7
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C

Using the IMS Emergency Flat
Tire Repair Kit
1. Park on a level surface off the right-of-
way and set the parking brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine.
3. Turn on the hazard warning flasher.4. Unload passengers and luggage, and
remove the emergency flat tire repair
kit.
5. Shake the tire sealant well.
NOTE
•The tire sealant cannot be reused.
Purchase new tire sealant at an
Authorized Mazda Dealer.
•The emergency flat tire repair kit
cannot be used in the following
cases.
Consult an Authorized Mazda
Dealer.
The period of effective use for
the tire sealant has expired. (The
period of effectiveness is
indicated on the bottle label.)
The tear or puncture exceeds
about 4 mm (0.16 in).
The damage has occurred to an
area of the tire other than the
tread.
The vehicle has been driven with
nearly no air remaining in the
tire.
The tire has come off the wheel
rim.
Damage to the wheel rim has
occurred.
The tire has two or more
punctures.
If the bottle is shaken after the
injection hose is screwed on, tire
sealant could spray out from the
injection hose. Tire sealant contacting
clothing or other objects may be
impossible to remove. Shake the bottle
before screwing on the injection hose.
CAUTION
J60E_8R65-EA-03C_Edition2.book Page 7 Saturday, April 26, 2003 1:48 PM

7-13
In Case of an Emergency
Flat Tire
Form No. 8R65-EA-03C
1. Park on a level surface off the right-of-
way and firmly set the parking brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1, and
turn off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, and tool (page 7-3).
6. Block the wheel diagonally opposite
the tire to be changed. When blocking
a wheel, place a block both in front and
behind the tire.
Changing the Tire
Jacking a Vehicle:
Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
Be sure to follow the directions for
changing a tire, and never get under a
vehicle that is supported only by a
jack.
Passenger in Vehicle Supported by a
Jack:
Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury. Never allow anyone inside a
vehicle supported by a jack.
(With Tire Pressure Monitoring
System)

The wheels equipped on your Mazda
are specially designed for installation
of the tire pressure sensors. Do not use
non-genuine wheels, otherwise it may
not be possible to install the tire
pressure sensors.
WARNING
CAUTION
NOTE
•Make sure the jack is well
lubricated before using it.
(With Tire Pressure Monitoring
System)

•Be sure to register the tire pressure
sensor ID signal code whenever tires
or wheels are changed (page 5-27).
J60E_8R65-EA-03C_Edition2.book Page 13 Saturday, April 26, 2003 1:48 PM