2004 MAZDA MODEL 6 oil dipstick

8-9
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I
Engine Compartment Overview
Automatic transaxle fluid-level dipstick
(only for automatic transaxle)
Cooling system cap Power steering
fluid reservoirWindshield washer
fluid reservoir
Engine oil dipstickEngine oil-filler cap
Engine coolant
reservoirBattery
Fuse block
Air filter Brake/Clutch fluid reservoir
Automatic transaxle fluid-level dipstick
(only for automatic transaxle)
Engine oil-filler cap Cooling system cap
Power steering
fluid reservoir Windshield washer
fluid reservoir
Engine oil dipstick Engine coolant
reservoir
Battery
Fuse block
Air filter Brake/Clutch fluid reservoir 2.3-liter engine
3.0-liter engine
shuseizumi_J56J_8R29_EA_02I.book Page 9 Saturday, September 7, 2002 12:58 PM

8-10
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I

Recommended Oil
Oil container labels provide important
information.
The quality designation SL
or ILSAC

must be on the label.
Engine oil viscosity, or thickness, has an
effect on fuel economy and cold-weather
operation (starting and oil flow).
Low-viscosity engine oils can provide
improved fuel economy and cold-weather
performance.
But high-temperature weather conditions
require higher-viscosity engine oils for
satisfactory lubrication.When choosing an oil, consider the
temperature range your vehicle will
operate in before the next oil change.
Then select the recommended viscosity
from this chart.
Energy conserving oils are recommended.
A chief contribution they make to fuel
economy is reducing the amount of fuel
necessary to overcome engine friction.

Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
Engine Oil
FORGASOLINEENGINES
(ILSAC)
–30–20–100 1020304050
–20 0 20 40 60 80 100 120
5W-20
Using oils of viscosity besides those
recommended for specific temperature
ranges could result in engine damage.
CAUTION
OKFull
Low 2.3-liter engine
shuseizumi_J56J_8R29_EA_02I.book Page 10 Saturday, September 7, 2002 12:58 PM

8-11
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I
5. Pull it out again and examine the level.
It’s OK between MIN and MAX.
But if it’s near or below MIN, add
enough oil to bring the level to MAX.
6. Make sure the O-ring is positioned
properly before reinserting the
dipstick.

Changing Engine Oil and Filter
Change engine oil and filter according to
Scheduled Maintenance (page 8-3).
Please act responsibly—protect the
environment and take used oil to a
recycling facility. Ask your dealer or a
service station for information.
Don’t add engine oil over MAX. This
may cause engine damage.
Full
OK
Low 3.0-liter engine
CAUTION
Handling Used Engine Oil:Continuous contact with used engine
oil is dangerous. It could cause skin
cancer. Always wash with soap and
water immediately after changing oil
and filter.
Remove any oil splatter from the
exhaust manifold, the exhaust pipe and
the shield. Oil left on these areas will
smoke when the engine is running.
WARNING
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 11 Saturday, September 7, 2002 12:58 PM

8-12
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I
Changing engine oil1. Warm up the engine for a few minutes
and turn it off. Remove the oil-filler
cap.
2. Remove the drain plug and drain the oil
into a suitable container.
3. Replace the plug tightly after the oil
has thoroughly drained.
4. Fill the engine with new oil to the
MAX mark on the dipstick.
5. Securely replace the oil-filler cap.
6. Start the engine and inspect around the
drain plug for leaks.
7. Turn it off and wait 5 minutes for the
oil to return to the oil pan.
Check the oil level and fill to the MAX
mark if necessary.
Oil capacity (General reference only,
refer to Specifications section for
capacities.)

Changing oil filter
Because you need a special tool to
retighten the filter, an Authorized Mazda
Dealer should do the work.
Checking or Changing Engine Oil:Hot engine oil is dangerous. If the
engine has been running, the engine
oil becomes very hot. You could be
seriously burned. Don’t check or
change the engine oil when the
engine is hot.
WARNING
FrontLoosen
Drain plugTighten 2.3-liter engine
Tighten
Loosen
Front
Drain plug3.0-liter engineNOTE
•
The indicated engine oil capacities
are for general reference purposes
only. When adding or changing oil,
verify the engine oil level with the
oil dipstick.
•
Use only specified engine oil (page
10-3).
shuseizumi_J56J_8R29_EA_02I.book Page 12 Saturday, September 7, 2002 12:58 PM

8-17
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I

Inspecting Power Steering Fluid
Level
2.3-liter engine
Inspect the fluid level in the reservoir at
each engine oil change with the engine off
and cold. Add fluid if necessary; it does
not require periodic changing.
The level must be kept between MIN and
MAX.
Visually examine the lines and hoses for
leaks and damage.If new fluid is required frequently, consult
an Authorized Mazda Dealer.
3.0-liter engine
Inspect the fluid level at each engine oil
change. Add fluid if necessary; it does not
require periodic changing.
The level must be kept between the H and
L marks.
Visually examine the lines and hoses for
leaks and damage.
1. Park on a level surface, well off the
right-of-way, and set the parking brake
firmly.
2. Turn off the engine and allow it to cool.
3. Remove the filler cap and attached
dipstick.
4. Wipe them clean and put them back.
5. Remove again and inspect the level.
6. It must be between H and L. Add fluid
if necessary.
Don’t overfill.

If new fluid is required frequently, consult
an Authorized Mazda Dealer.
Power Steering Fluid
To avoid damage to the power steering
pump, don’t operate the vehicle for
long periods when the power steering
fluid level is low.
NOTE
Use specified power steering fluid
(page 10-3).
CAUTION
High
OK
LowTighten
Loosen
shuseizumi_J56J_8R29_EA_02I.book Page 17 Saturday, September 7, 2002 12:58 PM

10-4
Specifications
Form No. 8R29-EA-02I

Capacities
(Approximate Quantities)
Check oil and fluid levels with dipsticks or reservoir gauges.

Dimensions
*116 inch wheel vehicle*217 inch wheel vehicle

We i g h t s

Air Conditioner
ItemUnit
L US qt Imp qt
Engine oil2.3-liter engineWith oil filter
replacement4.3 4.5 3.8
Without oil filter
replacement3.9 4.1 3.4
3.0-liter engineWith oil filter
replacement5.2 5.5 4.6
Without oil filter
replacement4.7 5.0 4.1
Coolant2.3-liter engine 7.5 7.9 6.6
3.0-liter engine 10.2 10.8 9.0
Manual transaxle oil2.3-liter engine 2.87 3.0 2.5
3.0-liter engine 2.3 2.4 2.0
Automatic transaxle fluid2.3-liter engine 7.2 7.6 6.3
3.0-liter engine 9.2 9.7 8.1
Fuel tank 68 18.0 (US gal) 15.0 (Imp gal)
Item Model
Overall length 4,745 mm (186.8 in)
Overall width 1,780 mm (70.1 in)
Overall height 1,440 mm (56.7 in)
Front tread
1,540mm
*1(60.6in), 1,530mm*2(60.2in)
Rear tread
1,540mm*1(60.6in), 1,530mm*2(60.2in)
Wheelbase 2,675 mm (105.3 in)
Item Weight
GVWR (Gross Vehicle Weight Rating) 1,958 kg (4,317 lb)
GAWR (Gross Axle Weight Rating)Front 1,070 kg (2,359 lb)
Rear 888 kg (1,958 lb)
Gas complies with SAE J639 Maximum operating charge
HFC134a (R-134a) 0.5 kg (17.6 oz)
shuseizumi_J56J_8R29_EA_02I.book Page 4 Saturday, September 7, 2002 12:58 PM