2004 MAZDA MODEL 3 HATCHBACK belt

5-37
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
Form No. 8S18-EA-03I

Seat Belt Warning Light/Beep
The seat belt warning light illuminates
and a beep sound will be heard if the
driver’s seat belt is not fastened when the
ignition switch is turned to the ON
position.
Conditions of operation
Belt minder
The belt minder is a supplemental
warning to the seat belt warning function.
This feature provides additional
reminders to the driver that the driver’s
seat belt is not fastened by intermittently
sounding a beep sound and flashing the
seat belt warning light in the instrument
cluster.
Condition
Result

The driver’s seat belt is
not fastened when the
ignition switch is
turned to the ON
position.The warning light
illuminates for about 1
minute and a beep
sound will be heard for
about 6 seconds.
The driver’s seat belt is
fastened while the
warning light and the
beep are activated.The warning light turns
off and the beep sound
stops.
The driver’s seat belt is
fastened before the
ignition switch is
turned to the ON
position.The warning light will
not illuminate and the
beep sound will not be
heard.
Condition
Result

The driver’s seat belt is
not fastened when the
vehicle speed reaches 8
km/h (5 mph) and
about 1 minute has
elapsed since the
ignition switch was
turned to the ON
position.The warning light
flashes and the beep
sound will be heard for
about 6 seconds every
30 seconds, for a
period of about 5
minutes.
The driver’s seat belt is
fastened while the
warning light and the
beep are activated.The warning light turns
off and the beep sound
stops.
The driver’s seat belt is
fastened before the
ignition switch is
turned to the ON
position.The warning light will
not illuminate and the
beep sound will not be
heard.
NOTE
The belt minder can be deactivated
temporarily using the following
methods:
1. Turn the ignition switch to the ON
position.
2. Fasten the driver’s seat belt for
about 2 seconds or longer, and then
unfasten it within 20 seconds.
The belt minder will be deactivated
until the ignition switch is turned to the
ON position again.
J48C_8S18-EA-03I_Edition1.book Page 37 Wednesday, August 6, 2003 8:51 AM

5-42
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
Form No. 8S18-EA-03I

Turn-Signal/Hazard Warning
Indicator Lights
When operating the turn-signal lights, the
left or right turn-signal indicator light
flashes to indicate which turn-signal light
is operating (page 5-47).
When operating the hazard warning
lights, both turn-signal indicator lights
flash (page 5-53).

Air Bag/Front Seat Belt
Pretensioner System Warning
Beep
If a malfunction is detected in the air bag/
front seat belt pretensioner systems and
the warning light, a warning beep sound
will be heard for about 5 seconds every
minute.
The air bag and seat belt pretensioner
system warning beep sound will continue
to be heard for approximately 35 minutes.
Have your vehicle inspected at an Mazda
Dealer as soon as possible.
NOTE
If an indicator light remains
illuminated (does not flash) or if it
flashes abnormally, the turn signal bulb
may be burned out.
Beep Sounds
Air Bag/Front Seat Belt Pretensioner
System Warning Beep:
Driving the vehicle with the air bag/
front seat belt pretensioner system
warning beep sounding is dangerous.
In a collision, the air bags and the
front seat belt pretensioner system
will not deploy and this could result in
death or serious injury.
Do not drive the vehicle with the air
bag/front seat belt pretensioner
system warning beep sounding.
Contact an Authorized Mazda Dealer
to have the vehicle inspected as soon
as possible.
WARNING
J48C_8S18-EA-03I_Edition1.book Page 42 Wednesday, August 6, 2003 8:51 AM

5-43
Driving Your Mazda
Warning/Indicator Lights and Beep Sounds
Form No. 8S18-EA-03I

Seat Belt Warning Beep
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep sound will be heard
for about 6 seconds.
The beep sound will be heard again for
about 6 seconds every 30 seconds, for a
period of about 5 minutes if the driver’s
seat belt is not fastened afterwards.
Refer to Seat Belt Warning Light/Beep
(page 5-37).

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep sound will be heard
when the driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep sound
will be heard when the driver’s door is
opened.

Tire Inflation Pressure Warning
Beep*
The warning beep sound will be heard for
about 3 seconds when there is any
abnormality in tire inflation pressures
(page 5-22).
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 43 Wednesday, August 6, 2003 8:51 AM

7-17
In Case of an Emergency
Emergency Starting
Form No. 8S18-EA-03I
Keep Flames Away:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all flames including
cigarettes and sparks away from open battery cells. When working near a battery, do
not allow metal tools to contact the positive ( ) or negative ( ) terminal of the
battery. Do not allow the positive ( ) terminal to contact the vehicle body.
Battery-Related Explosion:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all flames, including
cigarettes, and sparks away from open battery cells.
Low Fluid Level or Frozen Battery:
Jump-starting a frozen battery or one with a low fluid level is dangerous. It may
rupture or explode, causing serious injury.
Don’t jump-start a frozen battery or one with a low fluid level.
Connecting to Negative Terminal:
Connecting the end of the second cable to the negative ( ) terminal of the discharged
battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
Connect the cable to a point away from the battery.
Connecting Jumper Cable to Moving Parts:
Connecting a jumper cable near or to moving parts (cooling fans, belts) is dangerous.
The cable could get caught when the engine starts and cause serious injury. Never
connect a jumper cable to or near any part that moves.
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
WARNING
CAUTION
J48C_8S18-EA-03I_Edition1.book Page 17 Wednesday, August 6, 2003 8:51 AM

8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I

Schedule 1
I
: Inspect and repair, clean, adjust, or replace if necessary.
R
: Replace
L
: Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
CHASSIS and BODY
*1:According to state / provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
Maintenance Interval
(Number of months or
kilometers (miles), whichever
comes first)Months 6 12182430364248
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Engine valve clearanceA u d i b l e i n s p e c t e v e r y 1 2 0 , 0 0 0 k m ( 7 5 , 0 0 0 m i l e s ) ,
if noisy, adjust
Drive belts (tension)I
Engine oilRRRRRRRR
Engine oil filterRRRRRRRR
Cooling systemII
Engine coolantReplace at first 96,000 km (60,000 miles) or 4 years ;
after that, every 2 years
Air filterR
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Spark plugsReplace every 120,000km (75,000miles)
Brake lines, hoses and connectionsII
Disc brakesIIII
Tire (Rotation)Rotate every 12,000km (7,500miles)
Steering operation and linkagesII
Front and rear suspension and ball jointsII
Driveshaft dust bootsII
Exhaust system and heat shieldsInspect every 72,000km (45,000miles) or 60 months
All locks and hingesLLLLLLLL
J48C_8S18-EA-03I_Edition1.book Page 4 Wednesday, August 6, 2003 8:51 AM

8-5
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I

Schedule 2
I
: Inspect and repair, clean, adjust, or replace if necessary.
R
: Replace
L
:Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
ELECTRICAL SYSTEM
*1:According to state / provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage / kilometer period to ensure long-term reliability.
Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 1624324048566472808896
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Engine valve clearanceAudible inspect every 120,000km (75,000miles), if noisy, adjust
Drive belts (tension) I
Engine oilPuerto RicoReplace every 5,000 km (3,000 miles) or 3 months
OthersRRRRRRRRRRRR
Engine oil filterRRRRRRRRRRRR
Cooling systemII
Engine coolantR e p l a c e a t f i r s t 9 6 , 0 0 0 k m ( 6 0 , 0 0 0 m i l e s ) o r 4 y e a r s ;
after that, every 2 years
Engine coolant levelIIIIIIIIIIII
Air filterPuerto RicoRR
OthersR
Fuel lines and hoses
*1II
Hoses and tubes for emission
*1I
Spark plugsReplace every 120,000km (75,000miles)
Function of all lightsIIIIIIIIIIII
J48C_8S18-EA-03I_Edition1.book Page 5 Wednesday, August 6, 2003 8:51 AM

8-8
Maintenance and Care
Scheduled Maintenance
Form No. 8S18-EA-03I
I
: Inspect: Inspect and clean, repair, adjust, or replace if necessary.
R
: Replace
C
: Clean
*1:Also inspect and adjust the power steering and air conditioner drive belts, if installed.
*2: If the vehicle is operated under any of the following conditions, change the engine oil and oil filter more often
than recommended intervals.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation.
c) Driving for long period in cold temperatures or driving regularly at short distance only.
*3:If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air filter more often
than the recommended intervals.
*4:If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, change the brake fluid annually.
Maintenance
Interval
(Number of
months or
kilometers
(miles), whichever
comes first)Months 6 121824303642485460667278849096
×1000 km 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
×1000 miles6.25 12.518.752531.2537.543.755056.2562.568.757581.2587.593.75100
Engine valve clearanceAudible inspect every 120,000km (75,000miles), if noisy, adjust
Drive belts
*1IIIIIIIIIIIIIIII
Engine oil*2RRRRRRRRRRRRRRRR
Engine oil filter*2RRRRRRRRRRRRRRRR
Cooling systemIIIIIIII
Engine coolantReplace every 2 years
Air filter
*3CCRCCRCC
Spark plugsReplace every 120,000km (75,000miles)
Fuel filterRRRR
Fuel lines and hosesIIIIIIII
Evaporative system
(if installed)IIIIIIII
Battery electrolyte level and
specific gravityIIIIIIII
Brake lines, hoses and
connectionsIIIIIIII
Brake fluid
*4IIIRIIIRIIIRIIIR
Parking brakeIIIIIIIIIIIIIIII
Power brake unit
(Brake booster) and hosesIIIIIIII
Disc brakesIIIIIIIIIIIIIIII
J48C_8S18-EA-03I_Edition1.book Page 8 Wednesday, August 6, 2003 8:51 AM

8-31
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tire inflation pressures and
stay within the recommended load limits
and weight distribution.

Tire Inflation Pressure
The Tire Pressure Monitoring System*
does not alleviate the need to check the
tire condition every day, including
whether the tires all look inflated
properly. Inspect all tire pressure monthly
(including the spare) when the tires are
cold. Maintain recommended pressures
for the best ride, top handling, and
minimum tire wear.
Refer to the specification charts (page
10-8).
Tires
Using Different Tire Types:
Driving your vehicle with different
types of tires is dangerous. It could
cause poor handling and poor
braking; leading to loss of control.
Except for the limited use of the
temporary spare tire, use only the
same type tires (radial, bias-belted,
bias-type) on all four wheels.
Using Wrong-Sized Tires:
Using any other tire size than what is
specified for your Mazda (page 10-8)
is dangerous. It could seriously affect
ride, handling, ground clearance, tire
clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tires that
are the correct size specified for your
Mazda.
WARNING
Incorrect Tire Inflation:
Overinflation or underinflation of
tires is dangerous. Adverse handling
or unexpected tire failure could result
in a serious accident. Always inflate
the tires to the correct pressure (page
10-8).
WARNING
Tire pressure label
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 31 Wednesday, August 6, 2003 8:51 AM