2004 MAZDA MODEL 3 HATCHBACK turn signal

7-2
In Case of an Emergency
Form No. 8S18-EA-03I
Parking in an Emergency
The hazard warning lights should always
be used when you stop on or near a
roadway.
The hazard warning lights warn other
drivers that your vehicle is a traffic hazard
and that they must take extreme caution
when near it.
Depress the hazard warning flasher and
all four turn signals will flash.
Parking in an Emergency
NOTE
•The turn signals don’t work when
the hazard warning lights are on.
•Check local regulations about the
use of hazard warning lights while
the vehicle is being towed. They
may forbid it.
Hazard warning flasher
J48C_8S18-EA-03I_Edition1.book Page 2 Wednesday, August 6, 2003 8:51 AM

7-7
In Case of an Emergency
Flat Tire
Form No. 8S18-EA-03I
1. Park on a level surface off the right-of-
way and firmly set the parking brake.
2. Put a vehicle with an automatic
transaxle in Park (P), a manual
transaxle in Reverse (R) or 1, and turn
off the engine.
3. Turn on the hazard warning flasher.
4. Have everyone get out of the vehicle
and away from the vehicle and traffic.
5. Remove the jack, tool, and spare tire
(page 7-3).6. Block the wheel diagonally opposite
the flat tire. When blocking a wheel,
place a block both in front and behind
the tire.

Removing a Flat Tire
1. If your vehicle is equipped with a
wheel cover, pry off the wheel cover
with the beveled end of the lug wrench. (With Tire Pressure Monitoring
System)

The wheels equipped on your Mazda
are specially designed for installation
of the tire pressure sensors. Do not use
non-genuine wheels, otherwise it may
not be possible to install the tire
pressure sensors.
NOTE
•Make sure the jack is well
lubricated before using it.
(With Tire Pressure Monitoring
System)

•Be sure to register the tire pressure
sensor ID signal code whenever
tires or wheels are changed (page
5-24).
CAUTION
NOTE
When blocking a tire, use rocks or
wood blocks of sufficient size to hold
the tire in place.
Wheel cover
Lug wrench
J48C_8S18-EA-03I_Edition1.book Page 7 Wednesday, August 6, 2003 8:51 AM

8-36
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Light Bulbs
Side turn signal lightsFront turn signal lights/
Side-marker lightsRear turn signal lightsLicense plate light
Overhead light/Map lights (Front)*
Headlights (Low beam)
Headlights
(High beam)
Fog lights*Brake lights/Taillights
Reverse light High-mount brake light
Trunk light 4 Door
5 DoorOverhead light (Rear)
Overhead light/Map lights (Front)*
Headlights (Low beam)
Headlights
(High beam)
Side turn signal lightsFog lights*
License plate light
High-mount brake light
Luggage compartment
lightOverhead light (Rear)
Rear turn signal lights Brake lights/Taillights
Reverse light
Front turn signal lights/
Side-marker lights
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 36 Wednesday, August 6, 2003 8:51 AM

8-39
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
6. Replace the bulb.
7. Install the new bulb in the reverse order
of removal.
Replacing a fog light bulb*
1. Turn the screw counterclockwise and
remove it and partially peel back the
mudguard.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
Carefully remove the fog light bulb
from its socket in the reflector by
gently pulling it straight backward out
of the socket.3. Disconnect the bulb from the electrical
connector by pressing the tab on the
connector with your finger and pulling
the bulb upward.
4. Install the new bulb in the reverse order
of removal.
Front turn signal lights/Side-marker
lights
Due to the complexity and difficulty of
the procedure, the bulbs should be
replaced by an Authorized Mazda Dealer.
NOTE
•To replace the bulb, contact an
Authorized Mazda Dealer.
•Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
•When reinstalling the sealing cover,
make sure faces up.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Socket
Ta b
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 39 Wednesday, August 6, 2003 8:51 AM

8-40
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Side turn signal lights
1. Slide the unit as shown in the figure to
remove it.
2. Detach the electrical connector from
the unit by pulling it to the rear.
3. Install the new side turn signal unit in
the reverse order of removal.Brake lights/Taillights, Rear turn signal lights (4 Door)
1. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
2. Pull the center of each plastic retainer
and remove the retainers and partially
open the trunk side trim.
3. Turn the socket and bulb assembly
counterclockwise and remove it.
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Removal
InstallationTrunk end trim
Trunk side trim
Removal
Installation
J48C_8S18-EA-03I_Edition1.book Page 40 Wednesday, August 6, 2003 8:51 AM

8-41
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order
of removal.Brake lights/Taillights, Rear turn signal
lights (5 Door)
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Socket
Brake lights/Taillights
Rear turn signal lights
Left side
Right side
Socket
Brake lights/Taillights
Rear turn signal lights
J48C_8S18-EA-03I_Edition1.book Page 41 Wednesday, August 6, 2003 8:51 AM

8-49
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Fuse block (Passenger’s side)
37 38 39 4041 42
43 44 4546
47 48 49 5051
52 5354 55 56 5758
59 60 61 6263 64
65 66 67 68 6970
71 72 73 74 75 76 77 78 79 80 81 82 83 84 8586
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
37 D/LOCK 2 15A Power door lock
38—— —
39HEAD
HIGH L10AHeadlight high
beams (LH)
40HEAD
HIGH R10AHeadlight high
beams (RH)
41—— —
42—— —
43 CIGAR 15A Lighter
44 RADIO 7.5A Audio system
45 MIRROR 10APower control
mirror
46 TAIL R 7.5ATaillight (RH),
Parking lights (RH)
License plate lights
47 OBD 10AFor protection of
various circuits
48—— —
49 TR/LOCK 20A—
50 CPU PWR 10A Control unit
51 HAZARD 15A
Turn signals, Hazard
warning flashers
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
52SUN
RO O F20A
Moonroof
*
53 WASHER 20AFront washer, Rear
window wiper and
washer
54—— —
55 P/WIND R 30A—
56 P/WIND L 30A—
57 ALARM 7.5A—
58 M/DEF 7.5A Mirror Defroster
59—— —
60HEAD
LOW R15AHeadlight low
beams (RH),
Headlight leveling
*
61HEAD
LOW L15AHeadlight low
beams (LH)
62—— —
63—— —
64—— —
65 SAS 10ASupplemental
restraint system
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 49 Wednesday, August 6, 2003 8:51 AM

10-7
Specifications
Form No. 8S18-EA-03I

Light Bulbs
Exterior light

*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
Interior light

Light bulb WattageCategory
ECE R SAE
HeadlightsHigh beam 60 HB3—
Low beamHalogen 55 H7—
Xenon fusion 35 D2S—
Front turn signal lights/Side-marker lights 27/8—#1157NA
Fog lights
*55 H11—
Side turn signal lights*15WY5W—
High-mount brake light 18 W16W #921
Rear turn signal lights 21 W21W #7440
Brake lights/Taillights 21/5 W21/5W #7443
Reverse light 21 W21W #7440
License plate light 5 W5W—
Light bulb WattageCategory
ECE R
Trunk light (Sedan)
5W5W
Luggage compartment light (Hatchback)—
Overhead light/Map lights (Front)
*W5W
Overhead light (Rear) 10—
*Some models.
J48C_8S18-EA-03I_Edition1.book Page 7 Wednesday, August 6, 2003 8:51 AM