2004 MAZDA MODEL 3 5-DOOR brake

8-40
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
Side turn signal lights
1. Slide the unit as shown in the figure to remove it.
2. Detach the electrical connector from the unit by pulling it to the rear.
3. Install the new side turn signal unit in the reverse order of removal. Brake lights/Taillights, Rear turn signal lights (4 Door)
1. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.
2. Pull the center of each plastic retainer and remove the retainers and partially
open the trunk side trim.
3. Turn the socket and bulb assembly counterclockwise and remove it.
NOTE
Bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Removal
Installation Trunk end trim
Trunk side trim
Removal Installation
J48C_8S18-EA-03I_Edition3.book Page 40 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-41
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal. Brake lights/Taillights, Rear turn signal
lights (5 Door)
1. Remove the cover.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Socket
Brake lights/Taillights
Rear turn signal lights
Left side
Right side
Socket
Brake lights/Taillights
Rear turn signal lights
J48C_8S18-EA-03I_Edition3.book Page 41 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-43
Maintenance and Care
Owner Maintenance
Form No. 8S18-EA-03I
High-mount brake light
4 Door
1. Pull the center of each plastic retainer and remove the retainers and the trunk
rear trim.
2. Disconnect the electrical connector from the socket.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal. 5 Door
1. Remove the liftgate upper trim.
2. Disconnect the electrical connector
from the socket.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.
5. Install the new bulb in the reverse order of removal.
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Removal
Installation
Trunk rear trim
Socket
NOTE
To replace the bulb, contact an
Authorized Mazda Dealer.
Liftgate upper trim
Socket
J48C_8S18-EA-03I_Edition3.book Page 43 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-54
Maintenance and Care
Appearance Care
Form No. 8S18-EA-03I
To minimize scratches on the vehicle’s
paint finish:
• Rinse off any dirt or other foreign
matter using lukewarm or cold water
before washing.
• Use plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
• Rub gently when washing or drying the
vehicle.
• Take your vehicle only to a car wash
that keeps its brushes well maintained.
• Don
’t use abrasive cleansers or wax
that contain abrasives. Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don
’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
• Don
’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or
anodized aluminum parts. This may
damage the protective coating; also,
cleaners and detergents may
discolor or deteriorate the paint.
• To prevent damaging the antenna,
remove it before entering a car wash
facility or passing beneath a low
overhead clearance.
CAUTION
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
J48C_8S18-EA-03I_Edition3.book Page 54 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

8-56
Maintenance and Care
Appearance Care
Form No. 8S18-EA-03I

Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.

Aluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
Driving with Wet Brakes:
Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
• Don
’t use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
• Only use a mild soap or neutral
detergent and always use a sponge
or soft cloth to clean the wheels.
Rinse thoroughly with lukewarm or
cold water. Also, be sure to clean
the wheels after driving on dusty or
salted roads. This helps prevent
corrosion.
• Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
• If your aluminum wheels lose
luster, wax the wheels.
J48C_8S18-EA-03I_Edition3.book Page 56 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

10-4
Form No. 8S18-EA-03I
Specifications

Engine

Electrical System

Lubricant Quality
* Refer to the recommended SAE viscosity numbers on page 8-13.
Specifications
Item Model
2.0-liter engine 2.3-liter engine
Type DOHC-16V in-line, 4-cylinder
Bore ×
Stroke 87.5 ×
83.1 mm (3.44 ×
3.27 in) 87.5 ×
94.0 mm (3.44 ×
3.70 in)
Displacement 1,999 ml (1,999 cc, 121.9 cu in) 2,261 ml (2,261 cc, 137.9 cu in)
Compression ratio 10.09.7
Item Classification
Battery 12V-40AH/5HR, 12V-52AH/5HR, 12V-55AH/5HR
Alternator 12 V - 90 A
Starter 2.0-liter engine
12 V - 1.0 kW
2.3-liter engine 12 V - 1.4 kW
Spark-plug number NGK ITR6F 13
Spark-plug gap 1.25—1.35 mm (0.049 —0.053 in)
NOTE
When cleaning the iridium plugs, do not use a wire brush. The fine particulate coating
on the iridium alloy and platinum tips could be damaged.
Lubricant Classification
API Service ILSAC
Engine oil
*SL GF-III
Lubricant Classification
Manual transaxle oil Any temperature
API Service
GL-4 or GL-5
SAE 75W-90
Above 10 °
C (50 °
F) API Service
GL-4 or GL-5
SAE 80W-90
Automatic transaxle fluid ATF M-V
Power steering fluid ATF M-III or equivalent (e.g. Dexron® III)
Brake/Clutch fluid SAE J1703 or FMVSS116 DOT-3
J48C_8S18-EA-03I_Edition3.book Page 4 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

10-7
Specifications
Form No. 8S18-EA-03I

Light Bulbs
Exterior light

*1 Bulb replacement is not possible because it is built into the unit. Replace the unit.
Interior light
Light bulb WattageCategory
ECE R SAE
Headlights High beam
60 HB3—
Low beam Halogen
55H7 —
Xenon fusion 35 D2S —
Front turn signal lights/Side-marker lights 27/8—#1157NA
Fog lights
*55 H11 —
Side turn signal lights*15WY5W —
High-mount brake light 18 W16W #921
Rear turn signal lights 21 W21W #7440
Brake lights/Taillights 21/5 W21/5W #7443
Reverse light 21 W21W #7440
License plate light 5 W5W—
Light bulb WattageCategory
ECE R
Trunk light (Sedan)
5W5W
Luggage compartment light (Hatchback) —
Overhead light/Map lights (Front)
*W5W
Overhead light (Rear) 10—
*Some models.
J48C_8S18-EA-03I_Edition3.book Page 7 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI

11-2
Form No. 8S18-EA-03I
Index
A
Add-On Non-Genuine Parts and
Accessories
...................................... 9-13
Air Bag Systems
.............................. 2-36
Air Filter
.......................................... 8-23
Antenna
............................................ 6-10
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-8
Appearance Care
.............................. 8-51
Ashtray
............................................. 6-40
Audio System
................................... 6-10
Audio control switch
................ 6-32
Audio set
................................... 6-17
Operating tips for audio
system
....................................... 6-10
Safety certification
.................... 6-34
Automatic Transaxle Driving tips
............................... 5-16
Fluid
.......................................... 8-20
Manual shift mode
.................... 5-13
Shift-lock override
.................... 5-12
Shift-lock system
...................... 5-12
Transaxle ranges
....................... 5-11
B
Battery Emergency starting
................... 7-15
Maintenance
............................. 8-28
Specifications
........................... 10-4
Beep Sounds Ignition key reminder
............... 5-43
Lights-on reminder
................... 5-43
Seat belt warning beep
.............. 5-43
Tire inflation pressure warning
beep
........................................... 5-43
Before Starting the Engine
................. 4-6
After getting in
........................... 4-6
Before getting in
......................... 4-6
B
Body Lubrication ............................. 8-22
Bottle Holder
.................................... 6-42
Brake/Clutch Fluid
.......................................... 8-18
Brakes Anti-lock brake system (ABS)
....5-7
Brakes assist
................................5-8
Foot brake
................................... 5-4
Parking brake
.............................. 5-5
Warning light
.............................. 5-6
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-36
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Cargo Securing Loops
...................... 6-43
Cargo Sub-Compartment
................. 6-44
Catalytic Converter
............................ 4-3
Cell Phones
...................................... 9-14
Center Console
................................. 6-43
Child Restraint Child restraint precautions
........ 2-21
Installing child-restraint
systems
...................................... 2-25
LATCH child-restraint
systems
...................................... 2-32
Child Safety Locks for Rear
Doors
.................................................. 3-9
Cigarette Lighter
.............................. 6-40
Climate Control System
.....................6-2
Gas specifications
..................... 10-6
Clock
................................................ 6-39
Cruise Control
.................................. 5-18
Cup Holder
....................................... 6-41
Customer Assistance
.......................... 9-2
J48C_8S18-EA-03I_Edition3.book Page 2 Monday, February 9, 2004 8:41 PM
Black process 45.0 ° 240.0 LPI