2004 Lexus IS300 width

CHASSIS
355
SV63013a

Type BThe illustration indicates typical tire size.
1Tire use (P=Passenger car, T=Temporary use)
2Section width (in millimeters)
3Aspect ratio (tire height to section width)
4Speed category (alphabet with one letter)
5Tire construction code (R=Radial, D=Diagonal)
6Wheel diameter (in inch)
7Load index (2 digits or 3 digits)
8Speed symbol (alphabet with one letter)
SV63012c

1Section width
2Tire height
3Wheel diameter
03 07.09

CHASSIS
356
Name of each section of tire
SV63016

1Bead
2Sidewall
3Shoulder
4Tread
5Belt
6Inner liner
7Reinforcing rubber
8Carcass
9Rim lines
10Bead wires
11Chafer
Uniform tire quality grading
This information has been prepared in accordance
with regulations issued by the National Highway
Traffic Safety Administration of the U.S. Department
of Transportation. It provides the purchasers and/or
prospective purchasers of Lexus vehicles with
information on uniform tire quality grading.
Your Lexus dealer will help answer any questions
you may have as you read this information.
DOT quality grades - All passenger vehicle tires
must conform to Federal Safety Requirements in
addition to these grades. Quality grades can be
found where applicable on the tire sidewall between
tread shoulder and maximum section width. For
example: Treadwear 200 Traction AA Temperature
A
Tread wear - The treadwear grade is a comparative
rating based on the wear rate of the tire when tested
under controlled conditions on a specified government
test course. For example, a tire graded 150 would wear
one and a half (1 - 1/2) times as well on the government
course as a tire graded 100. The relative performance
of tires depends upon the actual conditions of their use,
however, and may depart significantly from the norm
due to variations in driving habits, service practices and
differences in road characteristics and climate.
03 07.09

CHASSIS
360
Occupant distributionDistribution of occupants in a vehicle as specified in the third column \
of Table 1
that follows.
RimA metal support for a tire or a tire and tube assembly upon which the ti\
re beads
are seated
Rim diameter
(Wheel diameter)Nominal diameter of the bead seat
Rim size designationRim diameter and width
Rim type designationThe industry of manufacturer's designation for a rim by style or code
Rim widthNominal distance between rim flanges
Vehicle maximum load on
the tireThe load on an individual tire that is determined by distributing to eac\
h axle its
share of the maximum loaded vehicle weight and dividing by two
Vehicle normal load on
the tireThe load on an individual tire that is determined by distributing to eac\
h axle its
share of the curb weight, accessory weight, and normal occupant weight
(distributed in accordance with Table 1 that follows) and dividing by two
Weather sideThe surface area of the rim not covered by the inflated tire
Table 1 ± Occupant loading and distribution for vehicle normal load fo\
r various designated seating capacities
03 07.09

CHASSIS
370
REPLACING WHEELS
When to replace your wheels
If you have wheel damage such as bends, cracks or heavy
corrosion, the wheel should be replaced.
If you fail to replace a damaged wheel, the tire may slip off the
wheel or cause loss of handling control.
Replacement with used wheels is not recommended as they
may have been subjected to rough treatment or high mileage
and could fail without warning. Also, bent wheels which have
been straightened may have hidden structural damage and
therefore should not be used. Never use an inner tube in a
leaking wheel which is designed for a tubeless tire.
Wheel selection
When replacing wheels, care should be taken to ensure
that they are equivalent to those removed in load capacity,
diameter, rim width, and offset.
Correct replacement wheels are available at your Lexus
dealer.
A wheel of a different size or type may adversely affect
handling, wheel and bearing life, brake cooling,
speedometer/odometer calibration, stopping ability, headlight
aim, bumper height, vehicle ground clearance, and tire or snow
chain clearance to the body and chassis.
CAUTION
Observe the following instructions. Otherwise, an
accident may occur resulting in death or serious
injuries.
Do not use wheels other than the manufacturer's
recommended size, as this may cause dangerous
handling characteristics resulting in loss of control.
03 07.09

BODY
392
SPECIFICATIONS (Sedan)
- DIMENSIONS AND WEIGHTOverall length
4485 mm (176.6 in.)
Overall width1725 mm (67.9 in.)
Overall height1410 mm (55.5 in.)*
Wheelbase2670 mm (105.1 in.)
Tread - Front - Rear1495 mm (58.9 in.)
1485 mm (58.5 in.)
Vehicle capacity weight (occupants + cargo)390 kg (860 lb.)
*Unladen vehicle
- FUEL TANK
Capacity
66 L (17.5 gal., 14.5 lmp.gal.)
03 07.09

BODY
393
SPECIFICATIONS (SportCross)
- DIMENSIONS AND WEIGHTOverall length
4495 mm (177.0 in.)
Overall width1725 mm (68.0 in.)
Overall height1430 mm (56.3 in.)*
Wheelbase2670 mm (105.1 in.)
Tread - Front - Rear1495 mm (58.9 in.)
1475 mm (58.1 in.) (with the 225/45ZR17 tires)
1485 mm (58.5 in.) (except the 225/45ZR17 tires)
Vehicle capacity weight (occupants + cargo)390 kg (860 lb.)
*Unladen vehicle
- FUEL TANK
Capacity
66 L (17.5 gal., 14.5 lmp.gal.)
03 07.09