2004 Lexus IS300 heating

SWITCHES
41
CAUTION
Occupants must use caution when operating the seat
heater because they may experience minor burns even
at low temperatures. Use extra caution for;
Babies, small children, elderly persons, sick persons
or handicapped persons
 Persons who have delicate skin
 Persons who are exhausted
 Persons who have taken alcohol or drugs which
induce sleep (sleeping drug, cold remedy, etc.).
To prevent the seat from overheating, do not use the
seat heater with a blanket, cushion, or other insulating
objects which cover the seat.
NOTICE
Do not put unevenly weighted objects on the seat and do not stick sharp objects (needles, nails, etc.) intothe seat.
When cleaning the seats, do not use organicsubstances (paint thinner, benzine, alcohol,gasoline, etc.). They may damage the heater and seat
surface.
To prevent the battery from being discharged, turn the switches off when the engine is not running.
03 07.09

INTERIOR EQUIPMENT
65
Cigarette Lighter
To use the cigarette lighter, press it in. After it finishes
heating up, it automatically pops out ready for use.
Do not hold the cigarette lighter pressed in.
If the engine is not running, the ignition key must be in the
ºACCº position to use the lighter.
Use a Lexus genuine cigarette lighter or equivalent for
replacement.
Ashtray
To use the ashtray, open the cover.
When finished with your cigarette, thoroughly extinguish it in
the ashtray to prevent other cigarette butts from catching fire.
After using the ashtray, close the ashtray cover completely.
To remove the ashtray, open the ashtray cover and pull it out.
CAUTION
To reduce the chance of injury in case of an accident or
sudden stop while driving, always completely close the
ashtray after use.
POWER OUTLET
SV14029a

In the console box
SV14010

In the luggage compartment (SportCross only)
03 07.09

AIR CONDITIONING
194SETTING OPERATION - manual control
If manual air flow selection is desired -
SV21017
The outlets from which air is delivered can be selected
manually by pushing the button. The function of each mode is
as follows:
1Panel
- Air flows mainly from the instrument panel vents.
2Bi-level - Air flows from both the floor vents and the
instrument panel vents.
3Floor - Air flows mainly from the floor vents.
4Floor/Windshield - Air flows mainly from the floor vents
and windshield vents.
Set the air flow control dial to the floor/windshield position
turns on the defogging function with the purpose of
clearing the front view.
Use with the air intake control positioned in fresh. Press the ºA/Cº button for dehumidified heating or
cooling. This setting clears the front view more quickly.
5Windshield
- Air flows mainly from the windshield vents.
Set the air flow control dial to the windshield position turns
on the defogging function with the purpose of clearing the
front view.
This position allows the air intake to select FRESH
automatically. This is to clean up the front view more
quickly.
If you want to return the setting to RECIRCULATE mode,
press the air intake selector button one again.
Press ºA/Cº button for dehumidified heating or cooling.
This setting clears the front view more quickly.
03 07.09

AIR CONDITIONING
195
If manual fan speed control is desired -
SV21023

1Fan speed at low 2Fan speed at high
The fan speed can be set to your desired speed by turning the
fan speed control dial. The higher the fan speed is, the more
air is delivered. Turning the dial to ºOFFº turns off the fan.
To remove exterior windshield frost, use the high speed
setting.
If manual switching of air intake is desired -
SV21024a
The air intake control button is used to switch the air intake
between the OUTSIDE AIR mode and RECIRCULATED AIR
mode.
With the button in the OUTSIDE AIR mode, the OUTSIDE AIR
mode ind
icator light will come on and the system will take fresh
outside air into the vehicle.
If quick circulation of cooled air is desired, push the air intake
control button for RECIRCULATED AIR. The
RECIRCULATED AIR mode indicator light will come on.
For normal use, it is best to keep the air intake control button
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.
When you adjust the airflow control dial and the fan speed
control dial to ºAUTOº positions in case that the room
temperature is much higher than the set temperature, the air
intake mode will be automatically changed to
RECIRCULATED AIR.
03 07.09

AIR CONDITIONING
196However, once selecting ºRECIRCULATED AIRº of the air
intake manually will make this function inoperable. In order to
make this function operable again, first select ºOUTSIDE AIRº
of the air intake, turn off the ignition switch, and start the engine
again. Then this function return to be operable.
If manual on-off of the air conditioning is desired -
Push the ºA/Cº button to turn the air conditioning on and push
it again to turn the air conditioning off.
The air conditioning does not work if the outside temperature
is lowered down to around 0C (32F).
If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year-round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the ºA/Cº button will blink. If the indicator of the
ºA/Cº button blinks even when the ºA/Cº button is pushed
again, have the compressor checked by your nearest Lexus
dealer.
(b) Windshield defogging and defrosting
SV21016
To remove interior fog on the windshield -
1. Turn the air flow control dial to ºWINDSHIELDº.
2. Set the ºOUTSIDE AIRº mode.
To remove frost or exterior fog on the windshield -
1. Turn the temperature control dial to the maximum
temperature.
2. Turn the air flow control dial to ºWINDSHIELDº.
3. Turn the fan speed control dial to ºHIº.
4. Leave the air conditioning on-off button off.
03 07.09

AIR CONDITIONING
200Heating
For best results, set controls to:
For automatic operation -
Set the air flow control dial and the fan speed control
dial to ºAUTOº position.
Temperature - To the desired temperature
Air intake - OUTSIDE AIR
For manual operation -Fan speed - To the desired fan speed
Temperature - Towards WARM (to the right)
Air intake - OUTSIDE AIR
Air flow - FLOOR
 For quick heating, select RECIRCULATED AIR for a few
minutes. To keep the windows from fogging, select OUTSIDE AIR after the vehicle interior has been warmed.
 Push the ºA/Cº button on for dehumidified heating.
 Choose floor/windshield air flow to heat the vehicle interior
while defrosting or defogging the windshield. Air conditioning
For best results, set controls to:
For automatic operation -
Set the air flow control dial and the fan speed control
dial to ºAUTOº position.
Temperature - To the desired temperature
Air intake - OUTSIDE AIR
For manual operation -Fan speed - To the desired fan speed
Temperature - Towards COLD (to the left)
Air intake - OUTSIDE AIR
Air flow - PANEL
 For quick cooling, select RECIRCULATED AIR for a few
minutes.
Ventilation
For best results, set controls to:
For automatic operation -
Set the air flow control dial and the fan speed control
dial to ºAUTOº position.
Temperature - Towards low temperature
Air intake - OUTSIDE AIR
03 07.09

AIR CONDITIONING
201
For manual operation -
Fan speed - To the desired fan speed
Temperature - Towards COLD (to the left)
Air intake - OUTSIDE AIR
Air flow - PANEL
Defogging and defrosting
- The inside of the windshield
For best results, set controls to:
For automatic operation -
Temperature - Towards high temperature to heat; low temperature to cool
Air intake - OUTSIDE AIR
AIR FLOW - WINDSHIELD
For manual operation -
Fan speed - To the desired fan speed
Temperature - Towards WARM (to the right) to heat;
COLD (to the left) to cool
Air intake - OUTSIDE AIR
Air flow - WINDSHIELD
Set the air flow control dial to the windshield or floor/windshield
position turns on the defogging function with the purpose of
clearing the front view. When turning the air flow selector to windshield position, the
air intake selects FRESH automatically.
This is to clean up the
front view more quickly.
If you want to return the setting to RECIRCULATE mode, press
the air intake selector button once again.
Press the ºA/Cº button for dehumidified heating or cooling. This
setting clears the front view more quickly.
 On humid days, do not blow cold air on the windshield - the
difference between the outside and inside temperatures could make the fogging worse.
- The outside of the windshield
For best results, set controls to:
For automatic operation -
Temperature - Towards high temperature
Air intake - OUTSIDE AIR
Air flow - WINDSHIELD
03 07.09

AIR CONDITIONING
202For manual operation -
Fan speed - To the desired fan speed
Temperature - Towards WARM (to the right)
Air intake - OUTSIDE AIR
Air flow - WINDSHIELD
Set the air flow control dial to the windshield or floor/windshield
position turns on the defrosting function with the purpose of
clearing the front view.
When turning the air flow selector to windshield position, the
air intake selects FRESH automatically. This is to clean up the
front view more quickly.
If you want to return the setting to RECIRCULATE mode, press
the air intake selector button once again.
Press the ºA/Cº button for dehumidified heating or cooling. This
setting clears the front view more quickly.
 To heat the vehicle interior while defrosting the windshield,
choose floor/windshield air flow.
Center vents
SV21031
The center vents may be opened or closed as shown.
Side vents
SS21019
The side vents may be opened or closed as shown.
03 07.09