2004 JEEP WRANGLER change time

CAUTION!
To avoid damage to the mirror during cleaning,
never spray any cleaning solution directly onto the
mirror. Apply the solution onto a clean cloth and
wipe the mirror clean.
The compass/temperature display provides the outside
temperature and one of eight compass headings (N, NE,
E, SE, S, SW, W, NW).Each time the center button is pressed and released
within 3 seconds, the display toggles through the follow-
ing three configurations:
²display compass/temperature (Fahrenheit),
²display compass/temperature (Celsius),
²and display off.
Compass Calibration
Automatic Calibration
Once calibrated, the compass has the ability to self-
correct for changes in magnetic field to keep the compass
accurate. This is referred to as Automatic Calibration. If
magnetic field changes are too great, the compass will
enter CAL mode on it's own and manual calibration will
be required. To recalibrate the compass, drive the vehicle
at less than 5 mph (8 km/h) through up to 1
1¤2360É turns
in an area free from large metal objects or power lines.
When the compass has been calibrated, the CAL symbol
will turn off and the compass will function normally.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 47
3

Parking Lights, Instrument Panel Lights, and
Headlights
Turn the end of the multi-function control lever to the
first detent for parking lights and instrument panel
lights. Turn to the second detent for headlight operation.
To change the brightness of the instrument panel lights,
rotate the center portion of the muti-function control
lever up or down.
NOTE:If the driver's door is left open, and the head-
lights or parking lights are left on, the ªHigh Beam
Indicator Lightº will flash and a chime will sound.
Lights-On Reminder
If the headlights or parking lights are on after the ignition
is turned off, a chime will sound when the driver's door
is opened.
Headlight Dimmer Switch
Pull the multi-function control lever towards you to
switch the headlights to HIGH beam. Pull the muti-
function control lever a second time to switch the head-
lights to LOW beam.
Passing Light
You can signal another vehicle with your headlights by
lightly pulling the multi-function control lever toward
the steering wheel. This will cause the headlights to turn
on at high beam and remain on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 57
3

Front Fog Lights Ð If Equipped
The front fog light switch is in the multi-function
control lever. To activate the front fog lights, turn
on the parking or low beam headlights and pull
out the end of the lever.
NOTE:The fog lights will only operate with the park-
ing lights or the headlights on low beam. Selecting high
beam headlights will turn off the fog lights.
Turn Signals
Move the multi-function control lever up or down and
the arrows on each side of the instrument cluster flash to
show proper operation of the front and rear turn signal
lights. You can signal a lane change by moving the lever
partially up or down without moving beyond the detent.
If either light remains on and does not flash, or there is a
very fast flash rate, check for a defective outside light
bulb. If an indicator fails to light when the lever is
moved, it would suggest that the fuse or indicator bulb is
defective.
NOTE:A tone will chime if the turn signals are left on
for more than 1 mile (2 km).
Daytime Running Lights Ð Canada Only
The headlights come on at a low intensity level after the
vehicle has been driven approximately 3 feet (1 meter).
They will turn off when the vehicle is turned off or when
the headlights are switched on.
WINDSHIELD WIPERS AND WASHERS
CAUTION!
In cold weather, always turn off the wiper switch
and allow the wipers to return to the park position
before turning off the engine. If the wiper switch is
left on and the wipers freeze to the windshield,
damage to the wiper motor may occur when the
vehicle is restarted.
Intermittent Wiper System
Use the intermittent wiper when weather conditions
make a single wiping cycle, with a variable pause be-
tween cycles, desirable. Move the lever to the DELAY
position, then select the delay interval by turning the end
58 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NTo Set The Radio Push-Button Memory......123
NOperating Instructions - RDS Mode........124
NTime Button.........................124
NTA (Traffic Announcement) Button.........125
NPTY (Program Type) Button..............125
NAF LOC (Alternative Frequencies And Local
Frequencies) Button....................126
NOperating Instructions - Tape Mode........126
NChanging Tape Direction................127
NSeek Button.........................127
NFast Forward (FF).....................127
NRewind (RW)........................127
NTape EjectD.........................127
NMetal Tape Selection (70s)..............127
NPinch Roller Release...................128
NDolby Noise Reduction.................128NOperation Instructions Ð CD Player........128
NInserting The Compact Disc..............128
NSeek Button.........................128
NEJT CD (Eject) Button..................129
NFF/Tune/RW Button...................129
NProgram Button 4 (Random Play)..........129
NCD/CDÐC/Tape Button................129
NTime Button.........................129
mSales Code RBBÐAM/FM Stereo Radio
With Cassette Tape Player And CD Changer
Capability
...........................130
NOperating Instructions..................130
NPower Button........................130
NElectronic Volume Control...............130
NSeek..............................130
NTune ..............................131
110 UNDERSTANDING YOUR INSTRUMENT PANEL

NTo Set The Push-Button Memory..........131
NBalance............................131
NFade..............................131
NBass And Treble Tone Control............131
NAM/FM Selection.....................132
NMode Button........................132
NCassette Player Features................132
NCD Changer Control Capability Ð
If Equipped.........................133
NRadio Display Messages................134
mSales Code RBKÐAM/ FM Stereo Radio
With CD Player And CD Changer Controls
...135
NRadio Operation......................135
NCD Player Operation...................137
NCD Changer Control Capability Ð
If Equipped.........................138
NRadio Display Messages................140
mSales Code RBT/RBYÐAM Stereo & FM Stereo
Radio With Graphic Equalizer, Cassette Tape
Player And CD Player
..................140
NOperating Instructions - Radio Mode.......140
NPower Switch, Volume Control............140
NSeek (Radio Mode)....................141
NTune ..............................141
NBalance............................141
NFade..............................141
NTone Control........................141
NAM/FM Selection.....................141
NTo Set The Radio Push-Button Memory......141
NTime ..............................142
NOperating Instructions - Tape Mode........142
N(¹D)...............................142
NTape ..............................142
UNDERSTANDING YOUR INSTRUMENT PANEL 111
4

5 seconds after pressing the SET button, the station will
continue to play, but will not be locked into push-button
memory.
You may add a second FM station to each push button by
repeating the above procedure with this exception: Press
the SET button twice and SET 2 will appear in the radio
display window. Each button can be set for SET 1 and
SET 2 in the FM mode. This allows for 10 FM stations to
be locked into push button memory. The stations stored
in SET 2 memory can be selected by pressing the push
button twice.
When you are receiving the MW or LW station that you
wish to commit to push-button memory, press SET 1
button. SET 1 will appear in the radio display window.
Select the push-button you wish to lock on this station
and press and release that button.
Operating Instructions - RDS Mode
The following RDS functions can be selected while in
radio mode by pushing the appropriate button.
Time Button
Briefly press the Time button to change the display
between radio frequency and time.
To set the ªHOME CLKº use a ballpoint pen or similar
object to press the hour (H) or minute (M) buttons on the
radio, The time setting will increase each time you press
the button. Press any other button to exit from the clock
setting mode.
Any time the hour (H) or minute (M) buttons are pressed
when in the ªRDS CLKº mode the clock will automati-
cally switch to the ªHOME CLKº mode and only the
home time will be set.
Pressing and holding the TIME button for 2 seconds will
toggle the clock between ªRDS CLKº and ªHOME CLKº.
The display will indicate which clock is activated. The
ªRDS CLKº is only updated by the signal transmitted
from a radio station with an RDS signal.
124 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE:When subjected to extremely cold temperatures,
the tape mechanism may require a few minutes to warm
up for proper operation. Sometimes poor playback may
be experienced due to a defective cassette tape. Clean and
demagnetize the tape heads at least twice a year.
Changing Tape Direction
Press the top of the PTY button to change tape play
direction. The display will confirm the selected tape play
direction. The time is always displayed.
Seek Button
Press the SEEK button up for the next selection on the
tape and down to return to the beginning of the current
selection.
Press the SEEK button up or down to move the track
number to skip forward or backward 1 to 7 selections.
Press the SEEK button once to move 1 selection, twice to
move 2 selections, etc. the display will show the total
number of times the SEEK button was pushed. The SEEK
function will be cancelled by pressing either the FF/RW
or FM/MW/LW button.
Fast Forward (FF)
Press the FF button up momentarily to advance the tape
in the direction that it is playing. The tape will advance
until the button is pressed again or the end of the tape is
reached. At the end of the tape, the tape will play in the
opposite direction.
Rewind (RW)
Press the RW button down momentarily to reverse the
tape direction. The tape will reverse until the button is
pressed again or until the end of the tape is reached. At
the end of the tape, the tape will play in the opposite
direction.
Tape EjectD
Press the Eject Tape button and the cassette will disen-
gage and eject from the radio.
Metal Tape Selection (70s)
If a standard 70  (metal) tape is inserted into the player,
the player will automatically select the correct equaliza-
tion.
UNDERSTANDING YOUR INSTRUMENT PANEL 127
4

EJT CD (Eject) Button
Press the EJT CD button and the disc will unload and
move to the entrance for easy removal. The unit will
switch to the radio mode. If you do not remove the disc
within 15 seconds, it will be reloaded, and the display
will remain unchanged in whatever mode it is in.
FF/TUNE/RW Button
Press FF (Fast Forward) and the CD player will begin to
fast forward until FF is released. The RW ( Reverse)
button works in a similar manner.
Program Button 4 (Random Play)
Press this button while the CD is playing to activate
Random Play. This feature plays the selections on the
compact disc in random order to provide an interesting
change of pace.Press the SEEK button to move to the next randomly
selected track.
Press button 4 a second time to stop Random Play.
CD/CDÐC/Tape Button
Press this button to select between CD player, Remote CD
changer, and Tape player.
Time Button
Press this button to change the display from elapsed CD
playing time to time of day.
UNDERSTANDING YOUR INSTRUMENT PANEL 129
4