2004 JEEP GRAND CHEROKEE differential

mode allows the front and rear wheels to rotate at
different speeds which eliminates driveline binding and
component wear that is normally associated with driving
the vehicle in the 4 PART TIME position on dry hard
surfaced roads. This feature provides the safety, security,
and convenience of operating in 4 wheel drive at all times
regardless of road conditions.
When additional traction is required, the 4 PART TIME
and 4LO positions can be used to lock the front and rear
driveshafts together through the transfer case inter-axle
differential and force the front and rear driveshafts to
rotate at the same speed. This is accomplished by simply
moving the shift lever to these positions. The 4 PART
TIME and 4LO positions are intended for loose, slippery
road surfaces only. Driving in the 4 PART TIME and 4LO
positions on dry hard surfaced roads may cause in-
creased tire wear and damage to driveline components.The PART TIME indicator light, located in the instrument
panel, alerts the driver that a four wheel drive mode
which locks the front and rear driveshafts together has
been selected. This light illuminates when the transfer
case is shifted to either the 4 PART TIME or 4LO
positions. There is no light for the 2WD, 4 FULL TIME, or
N (Neutral) positions.
NOTE:Do not attempt to make a shift while only the
front or rear wheels are spinning. The Selec-Tracttrans-
fer case is not equipped with a synchronizer and there-
fore the front and rear driveshaft speeds must be equal
for the shift to take place. Shifting while only the front or
rear wheels are spinning can cause damage to the trans-
fer case.
When operating your vehicle in 4LO, the engine speed is
approximately three times that of the 4 ALL TIME
position at a given road speed. Take care not to overspeed
the engine and do not exceed 25 mph (40 km/h).
STARTING AND OPERATING 187
5

Proper operation of four wheel drive vehicles depends on
tires of equal size, type, and circumference on each
wheel. Any difference will adversely affect shifting and
cause damage to the transfer case.
Because four wheel drive provides improved traction,
there is a tendency to exceed safe turning and stopping
speeds. Do not go faster than road conditions permit.
WARNING!
You or others could be injured if you leave the
vehicle unattended with the transfer case in the N
(Neutral) position without first fully engaging the
parking brake. The transfer case N (Neutral) position
disengages both the front and rear driveshafts from
the powertrain and will allow the vehicle to move
regardless of the transmission position. The parking
brake should always be applied when the driver is
not in the vehicle.
Shift Positions
For additional information on the appropriate use of each
transfer case mode position, see the information below:
2WD
Rear Wheel Drive High Range Ð Normal street and
highway driving. Dry hard surfaced roads.
4 PART TIME
Part Time 4 Wheel Drive High Range Ð Locks the
transfer case inter-axle differential. Forces the front and
rear wheels to rotate at the same speed. Additional
traction for loose, slippery road surfaces only.
4 FULL TIME
Full Time 4 Wheel Drive High Range Ð Employs inter-
axle differential. Allows front and rear wheels to rotate at
different speeds. All roads surfaces.
188 STARTING AND OPERATING

Chassis
Component Fluid, Lubricant, or Genuine Part
Automatic Transmission MopartATF+4 Automatic Transmission Fluid
Transfer Case Selec-Trac Models - MopartATF+4 Automatic Transmission Fluid. Quadra-Trac
Models - MopartTransfer Case Fluid (P/N 05016796)
Axle Differential (front-rear) MopartSynthetic Gear Lubricant or equivalent of SAE 75W-140 (API-GL5) if
equipped with a Vari-Loktfront axle. MopartGear Lubricant or equivalent of
SAE 80W-90 (API-GL5) if not equipped with a Vari-Loktfront axle. Mopart
Synthetic Gear Lubricant or equivalent of SAE 75W-140 (API-GL5) if equipped
with a Dana M35 or M44 Vari-Loktrear axle. MopartGear Lubricant or
equivalent of SAE 80W-90 (API-GL5) if equipped with a Dana M44 rear axle
without Vari-Lokt. For trailer towing applications, use a SAE 75W-140 Syn-
thetic Gear Lubricant in rear axle. Vari-Loktequipped axles require a friction
modifier additive.
Brake Master Cylinder MopartDOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is
not available, then DOT 4 is acceptable. Use only recommended brake fluids.
Power Steering Reservoir MopartPower Steering Fluid (MS-5931)
Ball Joints, Prop Shafts, U-Joints,
Yokes, & Wheel BearingsMopartMulti-Purpose Lube NLGI Grade 2 EP, GC-LB
MAINTAINING YOUR VEHICLE 293
7