2004 JEEP GRAND CHEROKEE heating

Gate Operator/Canadian Programming
Canadian radio-frequency laws require transmitter sig-
nals to9time-out9(or quit) after several seconds of
transmission - which may not be long enough for
HomeLink to pick up the signal during programming.
Similar to this Canadian law, some U.S. gate operators are
designed to9time-out9in the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using the9Program-
ming HomeLink9procedures (regardless of where you
live), replace step two with the following:
NOTE:If programming a garage door opener or gate
operator, it is advised to unplug the device during the
9cycling9process to prevent possible overheating.
Press and hold the HomeLink button while you press
and release - every two seconds ((cycle() your hand-heldtransmitter button until the radio signal has success-
fully been accepted by HomeLink. (The message
TRAINED will appear on the HomeLink display.)
Proceed with the remaining steps under9Programming
HomeLink9to complete.
Using HomeLink
To operate, simply press and release the programmed
HomeLink button. Activation will now occur for the
trained device (i.e. garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.). For convenience, the hand-held transmitter of the
device may also be used at any time. In the event that
there are still programming difficulties or questions,
contact HomeLink at:www.homelink.comor1-800-355-
3515.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
3

6. Do not expose the disc to direct sunlight.
7. Do not store the disc where temperatures may become
too high.
RADIO OPERATION AND CELLULAR PHONES
Under certain conditions, the cellular phone being On in
your vehicle can cause erratic or noisy performance from
your radio. This condition may be lessened or eliminated
by relocating the cellular phone antenna. This condition
is not harmful to the radio. If your radio performance
does not satisfactorily ªclearº by the repositioning of the
antenna, it is recommended that the radio volume be
turned down or off during cellular phone operation.
CLIMATE CONTROLS
Air Conditioning
The controls for the heating/air conditioning and venti-
lation system in this vehicle consist of a series of rotary
knobs. These comfort controls can be set to obtain desired
interior conditions.
Air conditioning can be obtained by depressing the
ªA/Cº button on the control panel and setting the
appropriate rotary knobs to obtain the desired comfort
level.
164 UNDERSTANDING YOUR INSTRUMENT PANEL

level is displayed the system will maintain that level
automatically using the heating system. Should the de-
sired comfort level require air conditioning, the system
will automatically make the adjustment.
You may notice the blower speed getting lower as the
difference between the driver and passenger temperature
settings gets larger. This is an extreme condition and the
airflow may not perform as anticipated.
The temperature can be displayed in U.S. or Metric by
selecting the US/M customer programmable feature.
Refer to the ªOverhead Console-Customer Program-
mable Featuresº in Section 3 of this manual.
The left knob controls the blower fan. Within the AUTO
setting on this control, you can select a HI volume of air
from the blower or a LO volume. Once the system is set
up for your comfort level, it is not necessary to change
the setting. You will experience the greatest efficiency by
simply allowing the system to function automatically.Manual Operation
However, this system does offer a full complement of
manual override features. There is a manual blower
range used when the AUTO setting is not desired. The
left control can be set to any fixed blower speed by
rotating the knob from LO to HI on the upper portion of
the dial.
The operator can override the AUTO mode setting and
select the direction of the air by rotating the right mode
knob to one of the following positions.
²Defrost
Air is directed to the windshield through the
outlets at the base of the windshield.
²Defrost/Floor
Air flows through the front and rear floor outlets
and the outlets at the base of the windshield.
168 UNDERSTANDING YOUR INSTRUMENT PANEL

The defroster will automatically turn off after about ten
minutes. For about five more minutes of operation, push
the button again. To prevent excessive battery drain, use
the defroster only when the engine is operating. The push
button also activates the heated exterior mirrors, if so
equipped.CAUTION!
Use care when washing the inside of the rear win-
dow to prevent damage to heating elements. Use a
soft cloth and a mild washing solution, wiping
parallel to the heating elements. Also, keep all
objects a safe distance from the window to prevent
damaging the heating elements.
172 UNDERSTANDING YOUR INSTRUMENT PANEL

reaches the appropriate temperature. Refer to the ªNoteº
under ªTorque Converter Clutchº later in this section.
If the transmission temperature gets too hot, the trans-
mission may downshift out of Overdrive or engage
overdrive at higher vehicle speeds (4.7L engines only)
until the transmission cools down. After cooldown, Over-
drive will resume normal operation.
2ÐSecond
For driving slowly in heavy city traffic or on mountain
roads where more precise speed control is desirable. Use
it also when climbing long grades, and for engine brak-
ing when descending moderately steep grades. To pre-
vent excessive engine speed, do not exceed 45 mph (72
km/h) in this range.
1ÐFirst
For driving up very steep hills and for engine braking at
low speeds (25 mph (40 km/h) or less) when going
downhill. To prevent excessive engine speed do not
exceed 25 mph (40 km/h) in this range.
CAUTION!
Never race the engine with the brakes on and the
vehicle in gear, and never hold the vehicle on an
incline without applying the brakes. These practices
can cause overheating and damage to the transmis-
sion.
184 STARTING AND OPERATING

Rocking the Vehicle
If the vehicle becomes stuck in snow, sand, or mud, it can
often be moved by a rocking motion. Move the gear
selector rhythmically between ªFirstº and R (Reverse),
while applying slight pressure to the accelerator.
The least amount of accelerator pedal pressure to main-
tain the rocking motion without spinning the wheels or
racing the engine is most effective. Racing the engine or
spinning the wheels, due to the frustration of not freeing
the vehicle, may lead to transmission overheating and
failure. Allow the engine to idle with the transmission
selector in N (Neutral) for at least one minute after every
five rocking-motion cycles. This will minimize overheat-
ing and reduce the risk of transmission failure during
prolonged efforts to free a stuck vehicle.CAUTION!
When ªrockingº a stuck vehicle by moving between
ªFirstº and R (Reverse), do not spin the wheels faster
than 15 mph (24 km/h), or drivetrain damage may
result.
FOUR-WHEEL DRIVE OPERATION
Selec-TracTOperating Instructions/Precautions
The Selec-Tracttransfer case provides five mode posi-
tions Ð two (rear) wheel drive high mode, part-time four
wheel drive high range, full-time four wheel drive high
range, neutral, and four wheel drive low range.
This transfer case is equipped with an inter-axle differ-
ential which allows driving the vehicle in the 4 FULL
TIME position at all times on any given road surface
including dry hard surfaced roads. The 4 FULL TIME
186 STARTING AND OPERATING

Always load a trailer with 60% of the cargo weight in the
front of the trailer. This places approximately 10% to 15%
of the GTW on the tow hitch of your vehicle. This portion
of the GTW becomes the tongue weight.
Trailer sway control and equalizing hitch are required for
tongue weights above 350 lbs (159 kg)., i.e., trailer
weights heavier than 3,500 lbs (1 587 kg).
Cooling System TipsÐTrailer Towing
To reduce potential for engine and transmission over-
heating in high ambient conditions, take the following
actions:
²City Traffic
When stopped, put transmission in N (Neutral) and
increase engine idle speed.
²Highway Driving
Reduce speed.
²Air Conditioning
Turn off temporarily.
To reduce the potential for transmission overheating,
turn the ªOverdriveº off when pulling any trailer or shift
the transmission to Drive position 2 on more severe
grades. Move the shift lever to the next lower position to
eliminate excessive transmission shifting. This action will
also reduce the possibility of transmission overheating
and provide better engine braking.
STARTING AND OPERATING 229
5

IF YOUR ENGINE OVERHEATS
In any of the following situations, you can reduce the
potential for overheating by taking the appropriate ac-
tion.
²On the highways Ð Slow down.
²In city traffic Ð While stopped, put transmission in N
(Neutral), but do not increase engine idle speed.
NOTE:There are steps that you can take to slow down
an impending overheat condition. If your air conditioner
is on, turn it off. The air conditioning system adds heat to
the engine cooling system and turning off the A/C
removes this heat. You can also turn the Temperature
Control to maximum heat, the Mode Control to floor, and
the Fan Control to High. This allows the heater core to act
as a supplement to the radiator and aids in removing heat
from the engine cooling system.
CAUTION!
Driving with a hot cooling system could damage
your vehicle. If the temperature gauge reads ªHº,
pull over and stop the vehicle. Idle the vehicle with
the air conditioner turned off until the pointer drops
back into the normal range. If the pointer remains on
the ªHº, and you hear continuous chimes, turn the
engine off immediately, and call for service.
WHAT TO DO IN EMERGENCIES 237
6