2004 JEEP GRAND CHEROKEE light

6. Do not expose the disc to direct sunlight.
7. Do not store the disc where temperatures may become
too high.
RADIO OPERATION AND CELLULAR PHONES
Under certain conditions, the cellular phone being On in
your vehicle can cause erratic or noisy performance from
your radio. This condition may be lessened or eliminated
by relocating the cellular phone antenna. This condition
is not harmful to the radio. If your radio performance
does not satisfactorily ªclearº by the repositioning of the
antenna, it is recommended that the radio volume be
turned down or off during cellular phone operation.
CLIMATE CONTROLS
Air Conditioning
The controls for the heating/air conditioning and venti-
lation system in this vehicle consist of a series of rotary
knobs. These comfort controls can be set to obtain desired
interior conditions.
Air conditioning can be obtained by depressing the
ªA/Cº button on the control panel and setting the
appropriate rotary knobs to obtain the desired comfort
level.
164 UNDERSTANDING YOUR INSTRUMENT PANEL

²Floor
Air flows through the floor outlets located under
the instrument panel and into the rear seating
area through vents under the front seats.
²Bi-Level
Air flows both through the outlets located in the
instrument panel and those located on the floor.
²Panel
Air flows through the outlets located in the in-
strument panel.
²OFF
This position turns off the entire system.
Depress the A/C button to turn on and off the air
conditioning during manual operation only. Conditioned
outside air is then directed through the outlets selected
on the mode control dial.When the outside air contains smoke, odors, high humid-
ity, or if rapid cooling is desired you may wish to
recirculate interior air by pressing the ªRecirculateº icon
button. The recirculation mode should only be used
temporarily. The light on the A/C and ªRecirculateº icon
buttons will illuminate when these buttons are selected.
You may use these features separately or with one
another. Push in on the buttons a second time to change
the functions.
NOTE:If the interior of the windows begins to fog,
press the ªRecirculateº icon button to return to outside
air. Some temp./humidity conditions will cause captured
interior air to condense on windows and hamper visibil-
ity. For this reason, the system will not allow ªRecircu-
lateº to be selected while in the defrost or defrost/floor
modes.
To provide you with maximum comfort in the automatic
mode, during cold start-ups the blower fan will remain
UNDERSTANDING YOUR INSTRUMENT PANEL 169
4

If the liftgate flipper glass is open, connection to the rear
window wiper is interrupted preventing activation of the
rear wiper blade. When the liftgate flipper glass is closed,
the rear wiper switch or the ignition switch needs to be
turned OFF and ON to restart the rear wiper.
Adding Washer Fluid
The fluid reservoir for the windshield washers and the
rear window washer is shared. It is located in the front of
the engine compartment on the passenger side and
should be checked for fluid level at regular intervals. Fill
the reservoir with windshield washer solvent (not radia-
tor antifreeze) and operate the system for a few seconds
to flush out the residual water.
Rear Window Defroster
In the lower left of the climate control panel is a
push button for rear window defrosting. An am-
ber indicator in the push button will light when the
defroster is turned on. Push again to turn off the defroster
prior to an automatic time-out.
UNDERSTANDING YOUR INSTRUMENT PANEL 171
4

²Vehicle speed is above approximately 30 mph (48
km/h).
²Transmission has reached normal operating tempera-
ture.
When frequent transmission shifting occurs while using
overdrive, such as when operating the vehicle under
heavy load conditions (for example, in hilly terrain,
strong head winds, or trailer towing), turning off over-
drive will improve performance and extend transmission
life by reducing excessive shifting and heat buildup.
4th and 5th gears (Overdrive) can be locked out by
pressing the O/D OFF switch located on side of the
gearshift lever. The O/D OFF indicator light will illumi-
nate to show that the switch has been activated. When
the light is on, 4th and 5th gears (Overdrive) are locked
out. Pressing the switch a second time restores the
Overdrive function. The lockout feature is useful when
towing a trailer or carrying a heavy load.The O/D OFF feature must be selected, if desired, each
time the engine is started.
NOTE:If the vehicle is started in cold outside tempera-
tures, shifts into Overdrive may be delayed (4.7L engines
only). Normal Overdrive and shifting operation will
resume when the temperature of the transmission
STARTING AND OPERATING 183
5

Over Temperature Mode
The transmission electronics constantly monitor the
transmission oil temperature. If the transmission gets too
hot, the transmission will change the way it shifts to help
control the condition. This may result in a slightly
different feeling or response during normal operation in
D (Drive) position. If the transmission becomes hot
enough the O/D OFF indicator light and TRANS OVER
TEMP warning light in the instrument cluster may come
on. After the transmission cools down, it will return to
normal operation.
Torque Converter Clutch
A feature designed to improve fuel economy has been
added to the automatic transmission of this vehicle. A
clutch within the torque converter engages automatically
at calibrated speeds. This may result in a slightly differ-
ent feeling or response during normal operation in high
gear. When the vehicle speed drops or during accelera-
tion, the clutch automatically and smoothly disengages.NOTE:
²The torque converter clutch will not engage until the
transmission fluid and engine coolant are warm (usu-
ally after 1±3 miles (1.6±4.8 km) of driving). Because
engine speed is higher when the torque converter
clutch is not engaged, it may seem as if the transmis-
sion is not shifting into ªOverdriveº when cold. This is
considered a normal condition. Pressing the ªO/D
OFFº switch will show that the transmission is able to
shift into and out of ªOverdrive.º
²If the vehicle has not been driven for several days, the
first few seconds of operation after shifting the trans-
mission into gear may seem sluggish. This is due to the
transmission fluid partially draining from the torque
converter into the transmission. This is considered a
normal condition and will not cause damage to the
transmission. The torque converter will refill within 5
seconds of shifting from P (Park) into any other gear
position.
STARTING AND OPERATING 185
5

Rocking the Vehicle
If the vehicle becomes stuck in snow, sand, or mud, it can
often be moved by a rocking motion. Move the gear
selector rhythmically between ªFirstº and R (Reverse),
while applying slight pressure to the accelerator.
The least amount of accelerator pedal pressure to main-
tain the rocking motion without spinning the wheels or
racing the engine is most effective. Racing the engine or
spinning the wheels, due to the frustration of not freeing
the vehicle, may lead to transmission overheating and
failure. Allow the engine to idle with the transmission
selector in N (Neutral) for at least one minute after every
five rocking-motion cycles. This will minimize overheat-
ing and reduce the risk of transmission failure during
prolonged efforts to free a stuck vehicle.CAUTION!
When ªrockingº a stuck vehicle by moving between
ªFirstº and R (Reverse), do not spin the wheels faster
than 15 mph (24 km/h), or drivetrain damage may
result.
FOUR-WHEEL DRIVE OPERATION
Selec-TracTOperating Instructions/Precautions
The Selec-Tracttransfer case provides five mode posi-
tions Ð two (rear) wheel drive high mode, part-time four
wheel drive high range, full-time four wheel drive high
range, neutral, and four wheel drive low range.
This transfer case is equipped with an inter-axle differ-
ential which allows driving the vehicle in the 4 FULL
TIME position at all times on any given road surface
including dry hard surfaced roads. The 4 FULL TIME
186 STARTING AND OPERATING

mode allows the front and rear wheels to rotate at
different speeds which eliminates driveline binding and
component wear that is normally associated with driving
the vehicle in the 4 PART TIME position on dry hard
surfaced roads. This feature provides the safety, security,
and convenience of operating in 4 wheel drive at all times
regardless of road conditions.
When additional traction is required, the 4 PART TIME
and 4LO positions can be used to lock the front and rear
driveshafts together through the transfer case inter-axle
differential and force the front and rear driveshafts to
rotate at the same speed. This is accomplished by simply
moving the shift lever to these positions. The 4 PART
TIME and 4LO positions are intended for loose, slippery
road surfaces only. Driving in the 4 PART TIME and 4LO
positions on dry hard surfaced roads may cause in-
creased tire wear and damage to driveline components.The PART TIME indicator light, located in the instrument
panel, alerts the driver that a four wheel drive mode
which locks the front and rear driveshafts together has
been selected. This light illuminates when the transfer
case is shifted to either the 4 PART TIME or 4LO
positions. There is no light for the 2WD, 4 FULL TIME, or
N (Neutral) positions.
NOTE:Do not attempt to make a shift while only the
front or rear wheels are spinning. The Selec-Tracttrans-
fer case is not equipped with a synchronizer and there-
fore the front and rear driveshaft speeds must be equal
for the shift to take place. Shifting while only the front or
rear wheels are spinning can cause damage to the trans-
fer case.
When operating your vehicle in 4LO, the engine speed is
approximately three times that of the 4 ALL TIME
position at a given road speed. Take care not to overspeed
the engine and do not exceed 25 mph (40 km/h).
STARTING AND OPERATING 187
5

Quadra-DriveTSystem Ð If Equipped
The optional Quadra-DrivetSystem features three
torque transfer couplings. The couplings include Vari-
Lok front and rear axles and Quadra-Trac IIttransfer
case. The optional Vari-Lok axles are fully automatic and
require no driver input to operate. Under normal driving
conditions the units function as standard axles balancing
torque evenly between left and right wheels. With a
traction difference between left and right wheels the
coupling will sense a speed difference. As one wheel
begins to spin faster than the other, torque will automati-
cally transfer from the wheel that has less traction to the
wheel that has traction. While the transfer case and axle
couplings differ in design, their operation is similar.
Follow the Quadra-Trac IIttransfer case shifting infor-
mation, preceding this section, for shifting this system.
VARI-LOK FRONT AND REAR AXLES Ð IF
EQUIPPED
The optional Vari-Lok axle is fully automatic and requires
no driver input to operate. Under normal driving condi-
tions the unit functions as a standard axle balancing
torque evenly between left and right wheels. With a
traction difference between left and right wheels the
coupling will sense a speed difference. As one wheel
begins to spin faster than the other, torque will automati-
cally transfer from the wheel that has less traction to the
wheel that has traction.
PARKING BRAKE
To set the parking brake, pull the lever up as firmly as
possible. When the parking brake is applied with the
ignition ON, the ªBrake Warning Lightº in the instru-
ment cluster will light.
194 STARTING AND OPERATING