2004 JAGUAR XJ Memory seats

Before Driving
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
Steering Column Adjustment . . . . . . . . . . . . . . . 3 - 7
Door Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 8
Interior Rear View Mirror . . . . . . . . . . . . . . . . . . 3 - 9
Occupant Protection . . . . . . . . . . . . . . . . . . . . 3 - 11
Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 11
Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 14
Child Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 23
LATCH Child Restraint System . . . . . . . . . . . . . 3 - 27
Memory Setting . . . . . . . . . . . . . . . . . . . . . . . . 3 - 31
Clock Adjustment . . . . . . . . . . . . . . . . . . . . . . . 3 - 32
Luggage Compartment . . . . . . . . . . . . . . . . . . . 3 - 33
Ski Hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 34

Before Driving 3 - 3
3 Before Driving
Seats
!WARNING:
1. Do not make adjustments when the vehicle is moving.
2. Front passengers must not ride with the seat fully reclined.
All seats, except the rear bench type,
are adjusted electrically by switches on
the side of the seat cushion. Adjustment
can be made with or without the ignition
key inserted.
Three different positions can be stored
and recalled by a memory system for
each seat. (Steering wheel, pedals and
door mirrors positions are also
memorised for the driver.) See Memory
Setting on page 3 - 31.
Note: It is advisable to move the seat to
the correct position in relation to the gear
lever and front and side vision before
adjusting the steering column, pedals,
mirrors and seat belt.
Front Seat Adjustment
Note: The full range of front seat
adjustments are: (
A ) – Backrest angle (recline) and headrest
height.
( B ) – Seat fore and aft position; cushion
height and front tilt:
• Move the switch forward or rearward to change the seat fore and aft
position.
• Move the centre or rear of the switch up or down to adjust cushion height.
• Move the front of the switch up or down to tilt the front of the cushion.
( C ) – Provides adjustable lumbar support
in the lower backrest. Either a 2-way or
4-way switch may be fitted:
• 2-way or 4-way switch: Press the
front or back of the switch to
increase/decrease lumbar support.
• 4-way switch only: Press the top of
the switch to increase higher lumbar,
decreasing lower lumbar support.
Press the bottom of the switch to
increase lower lumbar, decreasing
higher lumbar support. Press the front
of the switch to increase mid-lumbar
and the rear to decrease all lumbar
support.
( D ) – If specified, varies the cushion
extension. Moving the control will change
the distance between the front of the
cushion and the backrest.

Before Driving 3 - 31
Memory Setting
This facility enables three different
comfort positions to be memorised and
recalled for each occupant:
• The driver’s seat, steering column, pedals and exterior rear view mirrors.
• Rear passenger seat positions when memory is fitted to these.
The key does not have to be in the
ignition switch to make seat, steering
column and pedal adjustments but is
required to be in th e switch to set the
memory. Setting a memorised position
To store a driver’s seat position in the
memory:
1. Adjust the seat, steering column,
pedals and exterior rear view mirrors
to the desired positions.
2. Insert a key into the ignition switch and leave in the OFF position.
3. Push memory button M and the red LED in the switchpack will
illuminate for a five second period.
4. While the red LED is illuminated, push button ‘1’, ‘2’ or ‘3’ to memorise the
configuration. The LED will go out and
a chime will indicate that the setting
procedure is complete.
By repeating these three steps and
pressing the unused buttons, two more
driving positions can be stored in the
memory.
To set a new driving position, adjust to
the desired position and perform steps 2
and 3. The previous memory will be
erased and the new position will be set.
The rear passenger’s seats can also be
memorised by repeating steps 2 and 3
above after adjusting the seat to the
desired position. Recalling a memorise
d position from
the door switchpack
Ensure the gear selector lever is in
position ‘P’.
Press and release the appropriate
memory button (‘1’, ‘2’ or ‘3’). The seat,
steering column, pedals and door mirrors
will move automatically to the
memorised position.