2004 JAGUAR XJ 40 amp

4-60 On the Road
Use of Headlamps In Daylight
When visibility is poor the headlamps
with dipped beam setting should be
switched on so that the vehicle may be
seen more easily by other road users.
The instrument illumination dimmer
control adjusts the brightness of the panel
lighting.
Engine Oil Consumption
A certain amount of oil consumption is
normal. The rate of consumption will
depend on the following:
• The quality and viscosity of the oil.
• The amount of oxidation and dilution of the oil.
• Climatic conditions.
• The speed at which the engine is being operated.
• Road conditions.
Drivers should expect above normal
consumption when the engine is new,
and after running-in if high speeds are
sustained.
Winter Driving
Freeing a frozen door lock
Caution: Do not ap ply a proprietary
lock de-icer through the keyhole.
Should the lock beco me frozen, warm the
end of the key before use.
Windscreen wiper blades
Before driving away, clear any ice from
the windscreen and check that the wiper
blades are free. Switching on the heated
screen will accelerate this process.
The heated wiper park, if fitted, will come
on automatically.
Frost precautions
The correct concentration of coolant
must be maintained at all times when
‘topping up’ or ‘refilling’ the cooling
system.
Parking the Vehicle
When leaving the vehicle, remember the
following:
• Whenever the vehicle is being parked, apply the parkbrake and move the
gear selector to Park ‘P’.
• Do not leave children or pets in the vehicle unattended.
• Do not leave luggage or valuables on view. Always take your valuables with
you or lock them in the luggage
compartment.
• Remove the ignition key and spare keys, even when the vehicle is in your
garage.
• When the vehicle is unoccupied, close
all windows and lock all doors
securely.
• Park the vehicle where it can be seen. At night, park in a well-lit area.
• Ensure that the keys and the key transmitters are removed from the
vehicle before locking the doors,
and that all doors, the luggage
compartment and the hood are
closed.

4-64 On the Road
When filling, the dispenser nozzle must
be inserted into the filler neck sufficiently
to open the trap door for fuel to flow into
the fuel tank. For quickness and to
completely fill the ta nk, ensure that the
fuel nozzle rests on the filler neck as
shown. Fill the tank until the filler nozzle
automatically shuts off. Filling beyond
this point could result in fuel spillage.
After refuelling, refit the fuel filler cap in
to the filler neck, twist the filler cap
clockwise until it clicks and close the flap,
which automatically locks shut. The continuous use of high quality fuel
makes the need for a
dditional additives
unnecessary.
This will help to protect the engine
components against corrosion, carbon
deposit formation and prevent the fuel
injection system from clogging.
If in doubt your local Jaguar Retailer will
advise on which fuel must be used in
your vehicle.
Fuel requirements
The filler neck of the fuel tank is a small
diameter to suit the unleaded fuel pump
nozzle and will prevent the larger
diameter leaded fuel nozzle from entering
the filler neck.
Note: Not all countries have a small
diameter nozzle, for example, Japan,
so care must be taken to only fill the tank
with unleaded fuel.

4-68 On the Road
Catalytic Converters
A few precautions on the use of vehicles
fitted with catalytic converters are
necessary. These are:
1. In order to maintain the efficiency of the emission control system it is
essential that unleaded fuel is used.
Use of leaded fuel will seriously
damage the catalytic converters.
2. Heavy impact on the converter casings must be avoided.
3. The engine settings must not be altered; they have been established to
ensure that the vehicle will comply
with stringent exhaust emission
regulations. Incorrect engine settings
could cause unusually high catalytic
converter temperatures and thus
result in damage to the converter and
vehicle. If adjustment to the settings is
considered necessary, this should be
performed by a Jaguar Retailer. 4. A correctly tuned engine optimises
exhaust emissions, performance and
fuel economy and it is recommended
that the vehicle is regularly
maintained.
5. Do not continue to operate the vehicle if any engine malfunction is evident;
malfunctions should be rectified
immediately. For instance, misfire,
loss of engine performance, excessive
oil consumption or engine run-on may
lead to unusually high catalytic
converter temperatures and may
result in damage to the converters and
vehicle.
6. The use of catalytic converters increases exhaust system
temperatures, therefore, do not
operate or park the vehicle in areas
where combustible materials such as
dry grass or leaves may come into
contact with the exhaust system. 7. Do not run the engine with either a
spark plug lead disconnected or a
spark plug removed. Do not use any
device that requires an insert into a
spark plug hole in order to generate air
pressure e.g. tyre pump, paint spray
attachment etc., as this could also
result in catalyti c converter damage.
8. The vehicle is designed for normal road use. Below are examples of abuse
which could damage the catalytic
converters and vehicle. These may
lead to a dangerous condition due to
excessively high catalytic converter
temperatures.
• Competition or off-road use.
• Excessive engine speed.
• Overloading the vehicle.
• Switching off the engine whilst in gear.

5 - 6 Climate Control
Front Climate Controls
The climate control functions are selected
by push buttons and a rotary control.
When a button is pressed, selection of
the function is confirmed by a beep; most
buttons also have an illuminated LED.
Many system functions also have graphic
symbols displayed on the LCD (liquid
crystal display) screen.
Automatic control (AUTO) may be
overridden at any time. Defrost/demist
operation is available and also manual
selection of blower speed,
air distribution, recirculation,
air conditioning and windscreen heating.
Panel illumination
With the exterior lighting switched on or
Autolamps selected at night, the graphics
on the panel controls are illuminated by
low level backlighting.
In countries with daytime runnin g lamps,
the panel illumination will not be on
during daytime if the headlamp switch is
off or in Autolamp position unless it is
dark and the autolamp selects the
headlamps on.
The illumination level is adjusted by the
common instrument panel dimmer
control (see page 4 - 25). 1.
Blower speed and system on/off.
2. Display panel.
3. Fahrenheit/Celsius selector.
4. Air conditioner on/off.
5. Select automatic operation.
6. Recirculation/fresh air.
7. Increase right zone temperature.
8. Decrease right zone temperature. 9.
Select air distribution.
10. Heated rear screen/door mirrors.
11. Heated front screen (optional).
12. Defrost windows.
13. Select dual/single temperature zone.
14. Increase left zone temperature.
15. Decrease left zone temperature.
16. Option without fron t screen heater.

Climate Control 5 - 9
Manual Air Distribution
Air distribution is automatically
controlled in AUTO and defrost modes.Press MODE to select manual air
distribution.
Four air distribution modes are
available and are selected in succession
by pressing the MODE button. A symbol
is displayed for the selected mode.
To Switch the System Off
Press in the blower rotary
control knob to switch the
climate control system off.
If the blower control knob is
pressed again, the system will switch on
in the previous mode set.
4-zone climate control system
If 4-zone climate control is fitted,
switching off front climate control (above)
will also cause the rear climate control
system to be switched off. Switching the
front system on again will not switch the
rear system on.
Ram Air
With the climate control system switched
off, air recirculation is automatically
selected (intake flap closed). To select
fresh air with the system off, press the
MODE button to select one of the air
distribution modes.
With the blower switched off, the fresh
airflow results from the forward motion
of the vehicle (ram air effect).
Smog sensing
Where fitted, the smog sensor detects
road traffic pollutants and automatically
selects air recirculation when the level of
pollution outside the vehicle reaches a
certain level. The level of pollution at
which the smog sensor will respond can
be adjusted.
Once the level of pollutants decreases,
air recirculation will switch off (subject to
the normal operation of the automatic
climate control system).
To adjust smog sensitivity: Press the
air recirculation and AUTO buttons
simultaneously. The display will show a
number between 0 and 5: 0 indicates
that the smog sensor is switched off, and
5 shows that the sensor is set to its most
sensitive setting. Use the driver’s
temperature control bu ttons to increase
or decrease the smog sensitivity.
Caution: Don’t set the smog sensor to
a needlessly high level in cold and
damp conditions: This could result in
interior condensation.
Airflow distributed to the
windscreen and feet; select to
prevent or remove light misting
and when heating the interior.
Airflow directed to foot level;
select to heat the interior.
Airflow distributed to the face
and feet.
Airflow directed at face level
only; select to cool the interior.

Roadside Emergency 6 - 15
Dipped beam (outer) headlights
Caution: Halogen bulbs will be
damaged if touched by hand or
contaminated with oil or grease. It is
important to use clean gloves or cloth
when handling a bulb which is to be
used again. A contaminated bulb may
be cleaned with methylated spirit
before refitting.
Open the hood and remove the top cover
as shown on page 6 - 14.
Pull the retaining clip (arrowed in A
above) upwards. Move the top of
headlight assembly outer bulb cover
rearwards to gain a ccess to the bulbs. Pull off the bulb connector. Release the
bulb spring clip (
B) from below the bulb
and lift it clear of the bulb. Pull out the
bulb from the headlight assembly.
Locate the new bulb (type H7) into the
headlight with the bulb tab
uppermost ( C). The bulb will only fit
correctly in one position.
Engage the spring clip ( B) to secure the
bulb. Fit the bulb connector.
Refit the bulb cover to the headlight
assembly and secure with the retaining
clip.
Refit the top cover and close the hood.
It is advisable to have the headlight aim
checked by a Retailer after bulb renewal. Front direction indicator bulb
The front direction indicator bulb is
located above the outer headlight bulb
(halogen or HID type) and is accessed via
the outer bulb cove
r (see column 1).
Turn the bulb holder a quarter turn anti-
clockwise and pull out ( D).
Remove the bulb and fit a new one of the
correct type, PY21W.
Fit the bulb holder to the lamp unit,
it will only fit in one position.
Turn clockwise to secure. Refit the
headlight assembly ou ter bulb cover and
secure with the retaining clip.
Refit the top cover and close the hood.

6 - 18 Roadside Emergency
Side marker – bulb renewal
Remove the side marker lamp by sliding it upwards to compress
the spring clips. While still holding the lamp up, against the
spring clips, gently ease the bottom of the lamp from the
bumper. Remove the lamp.
Twist the bulb holder anti-clockwi se to remove it from the lamp
assembly.
Fit a new bulb of the correct type, W5W to the bulb holder.
Position the bulb holder to th e lamp assembly and twist it
clockwise to refit it.
Carefully press the lamp assembly into the recess until it clicks
into place.

Roadside Emergency 6 - 19
Rear light assembly – bulb renewal
On the rear light assemblies, only the direction indicator,
reverse and fog bulbs are replaceable. The stop/tail lamps
consist of arrays of LED lights which can only be renewed by a
Jaguar Retailer if they fail to operate.
Ensure that the lights and ig nition switch are OFF before
removing any bulbs.
Open the trunk and secure the floor panel in the open position.
See page 6 - 4.
Rotate fastener ( A) a quarter turn and remove. Pull back the
side carpet trim to access the rear of the light assembly.
The bulb positions are:
1. Reverse light, type P21W.
2. Direction indicator, type PY21W.
3. Fog light, type P21W.
Rotate the bulb/connector and wi thdraw it from the assembly.
Remove the faulty bulb and fit a new one of the correct type,
as illustrated on the bulb holder. It is essential to fit the correct
type.
Reposition the bulb/connector and turn it to secure.
Carefully refit the side carpet trim. Fit fastener ( A) and rotate a
quarter turn.
Close the trun k floor panel.