2004 JAGUAR XJ seat

3 - 28 Before Driving
Fitting LATCH seats
For further information regarding a LATCH child seat, please
consult your Jaguar Retailer.
Always use the additional top tether anchorage.
LATCH child seats can only be fi tted to the two outer rear seat
positions, as shown on the previous page.
Caution: When fitting a LATCH child seat, the seat
manufacturers instructions must always be followed.
The following is a guide only.
Note: So as not to interfere with the fitment of large child seats,
push the adult seat buckles into their buckle recesses and,
if necessary, remove the headrest.
LATCH seat with extendable bars (A) – Fit the seat as
follows:
1. Expose the LATCH loops between the seat and seat back.
2. Make sure that the adult seat belts and buckles do not become trapped behind the child seat.
3. Make sure there is nothing obstructing the seat mounting mechanism at the anchorage points.
4. Make sure you do NOT trap the top tether strap behind the child seat.
5. Fully extend the two attachme nt bars on the child seat
(see manufacturer’s instructions).
6. Locate the slots on the ends of the bars onto the two LATCH
loops, then push the seat asse mbly rearwards until the bars
are positively engaged (a trigger operates to lock the
attachment bars onto the loops). 7. Slide the seat rearwards along the legs until it is locked firmly
against the vehicle seat back. Confirm that it is securely
locked in position.
8. Secure a forward-facing ch ild seat to the top tether
anchorage.
LATCH seat with tether straps (B) – Clip the flexible lower
straps to the two LATCH loops. Adjust the length of each strap
until the seat is held firmly against the vehicle seat back.
!WARNING:
Do not install a LATCH child seat with flexible lower
attachments in the vehicle centre seat position.
The anchorage loops are only provided to install a
compatible child seat in the vehicle outboard seat
positions.

Before Driving 3 - 29
Child restraint top tether anchorages and brackets
!WARNING:
The top tether must always be used to secure forward-
facing child seats.
The top of the child seat is connected by a short strap to a top
tether bracket to prevent any tendency of the seat to rotate
about the lower anchorages. The top tether brackets are
positioned on the rear parcel shelf, under access covers, at the
centre-line of each rear seating position.
Fit the top tether in combination with the lower LATCH
attachments or other child restraints to secure the seat.
Connect the top tether to the child seat (if it is not part of the
seat) and pass it under the vehicle rear head restraint to connect
to the fixed tether bracket on the rear shelf. Adjust the length of
the top tether strap to hold the top of the child seat against the
vehicle seat back.
!WARNING:
Child restraint anchorages are designed to withstand only
those loads imposed by correctly fitted child restraints.
Under no circumstances are they to be used for adult seat
belts or for attaching other items or equipment to the
vehicle.

3 - 30 Before Driving
Check List – LATCH Child
Restraints
Follow the check list each time your child
travels in the vehicle:
• Always attach the top tether when installing a forward-facing seat.
• Carefully follow the instructions supplied with the child seat.
• Always give the seat a final pull to ensure the lower anchors are secure,
even if the seat has indicators to show
that the seat connectors are latched.
• Always use the appropriate child restraints and adjust harnesses for
every child, every trip.
• Make sure you use a seat with the correct weight range for your child. • Avoid dressing your child in bulky
clothing and do not place any objects
between the child and the restraint
system.
• Regularly check the fit of your child seat and replace seats or harnesses
that show signs of wear.
• No child seat is completely child- proof. Encourage your child not to
play with the buckle or harness.
• Never leave a child unsupervised in the vehicle.
• Activate the rear door child safety locks (see page 2 - 14).
• Ensure your child does not exit the vehicle from the side where there is
traffic.
• Set your child a good example – always wear your seat belt.

Before Driving 3 - 31
Memory Setting
This facility enables three different
comfort positions to be memorised and
recalled for each occupant:
• The driver’s seat, steering column, pedals and exterior rear view mirrors.
• Rear passenger seat positions when memory is fitted to these.
The key does not have to be in the
ignition switch to make seat, steering
column and pedal adjustments but is
required to be in th e switch to set the
memory. Setting a memorised position
To store a driver’s seat position in the
memory:
1. Adjust the seat, steering column,
pedals and exterior rear view mirrors
to the desired positions.
2. Insert a key into the ignition switch and leave in the OFF position.
3. Push memory button M and the red LED in the switchpack will
illuminate for a five second period.
4. While the red LED is illuminated, push button ‘1’, ‘2’ or ‘3’ to memorise the
configuration. The LED will go out and
a chime will indicate that the setting
procedure is complete.
By repeating these three steps and
pressing the unused buttons, two more
driving positions can be stored in the
memory.
To set a new driving position, adjust to
the desired position and perform steps 2
and 3. The previous memory will be
erased and the new position will be set.
The rear passenger’s seats can also be
memorised by repeating steps 2 and 3
above after adjusting the seat to the
desired position. Recalling a memorise
d position from
the door switchpack
Ensure the gear selector lever is in
position ‘P’.
Press and release the appropriate
memory button (‘1’, ‘2’ or ‘3’). The seat,
steering column, pedals and door mirrors
will move automatically to the
memorised position.

3 - 32 Before Driving
Memory recall using an integrated
key
The integrated key will recall a memory
position when the unlock button is
pressed when set as follows:
1. Adjust the seat, steering column, pedals and exterior rear view mirrors
to the desired positions.
2. Press the M button: The red LED will illuminate for a five second period.
3. Press button ‘1’, ‘2’ or ‘3’ and then press any button on the integrated
key. Both button presses must occur
while the red LED is illuminated.
4. Repeat for the other integrated key, pressing the remaining memory
buttons.
To cancel integrated key memory recall:
1. Place a key into the ignition switch and leave in the OFF position.
2. Press the M button: The red LED will illuminate for a five second period.
3. Press any button on the integrated key
(except the panic button, if fitted) then
press the M button again. Both button
presses must occur while the red LED
is illuminated. Note:
If memory recall is performed
using an integrated ke y with the vehicle in
entry/exit position, the steering column
and seat will not return to the memorised
position until either the integrated key is
placed in the ignition switch or the
driver’s door is closed.
Driving position memory system
operating tips
• When making adjustments to a set driving position, reset the new
position in the same memory channel.
• A driving position will only be memorised during the five second
period when the red memory LED is
illuminated.
• Previous memory is erased when a new driving position is entered.
Clock Adjustment
The analogue clock is adjusted by
pressing the (+) and (–) buttons below
the dial. Pressing and holding either
button will increase the rate of hand
movement forwards or backwards as
required.

3 - 34 Before Driving
Ski Hatch
A two-door hatch is fitted to the rear seat
on some models, providing an opening
between the passenger and luggage
compartments. This allows space for skis
or similar objects to be stowed in the
vehicle. Both doors have a single catch.
The inner door is accessible after folding
down the armrest. To open the door, pull
the leather flap forward, press the
catch (A) downwards and gently lower
the door on to the armrest.
A bag for retaining the skis can now be
pulled from the receptacle into the
passenger compartment, and the strap ( C)
loosened ready to accept the skis.
The other door is accessible from inside
the luggage compartment and is opened
by pushing the catch ( B) and lowering the
door.
Push the skis into the bag from the
luggage compartment and then secure
the skis using the strap provided on the
bag. Clip the strap connector ( D) to the
centre rear seat belt buckle.

4-6 On the Road
Charge Indicator (RED)
This lights up when the ignition
is switched ON and should go
out when the engine is
running.
If the light stays ON when the engine is
running it indicates that there is either a
battery voltage fault or a generator fault.
Turn OFF all electrical accessories, radio,
climate control, rear screen heater etc.
Try to use the minimum electrical load as
possible such as power windows, electric
sunroof etc. Report the fault to a Jaguar
Retailer.
Seat Belt (RED)
The warning lamp lights when
the ignition is ON and:
• The driver’s seat belt is not fastened.
• A passenger is sitting in the front seat and their seat belt is not fastened.
The light should go out when the driver’s
seat belt (and the front passenger’s if the
seat is occupied) is fastened.
Note: The vehicle must be moving above
10 mph (16 km/h) for the lamp to
illuminate if the passeng er seat belt is not
fastened.
Beltminder
The Beltminder feature is a supplemental
warning to the seat be lt warning function.
This feature provides additional
reminders to the driver that the driver’s
and/or front passenger’s seat belt is
unbuckled by intermittently sounding a
chime and illuminating the seat belt
warning light in the instrument cluster. If the vehicle is moving above 10 mph
(16 km/h) and one or both front seats are
occupied and a seat belt is not fastened,
a warning chime will be heard and the
light will flash.
The chime sound and the light flashing
will last for 10 seconds and then repeat
every 30 seconds for five minutes or until
the belts are fastened or the vehicle
stops.
If the warning light stays ON steady with
the seat belt(s) fastened, report the fault
to a Jaguar Retailer. It is safe to drive the
vehicle with the light ON steady,
provided that the seat belt(s) is properly
fastened. Ensure that all occupants seat
belts are fastened before driving.
Although not advisable, it is possible to
disable or reinstate the Beltminder
function. Please see a Jaguar Retailer.
Note:
If a heavy object is placed on the
front passenger seat it may activate the
Beltminder feature. It is recommended
that the object be placed in the luggage
compartment.

On the Road 4 - 11
Hazard or ConditionRemedy/chime or tone
Valet mode. This indicates that the valet mode has not been set or that access to a
restricted area has been prevented because valet mode has been set.
Seat belt reminder. A chime will sound for 60 seconds after the ignition is switched on or until
the driver’s seat belt is fastened or the ignition switch turned to ‘0’.
The chime will also sound at regular intervals for five minutes if the vehicle is
moving above 10 mph (16 km/h) and the driver’s and/or front passenger’s
(if occupied) seat belts are not fastened or are unfastened.
Electric parkbrake. If the message ‘PARKBRAKE ON’ is displayed, it means that the parkbrake is
applied but the vehicle is moving. Release the parkbrake or stop the vehicle
when it is safe to do so.
Parkbrake cannot be applied. This sounds a warning that the parkbrake cannot be applied. The parkbrake
needs to be reset. Release the parkbrake, depress the footbrake and at the
same time apply the parkbrake.
Adaptive cruise control driver intervene. Action is required by the driver to apply the brakes.
Gear selector not in ‘Park’. This warns that the gear selector is not in Park when the ignition is turned off.