2004 ISUZU TF SERIES ignition

1-90 HEATER AND AIR CONDITIONING

MAGNETIC CLUTCH DOES NOT RUN (4JA1L/4JH1-TC)



Replace
YES


Are the A/C thermo (X-15) and heater & A/C (X-11)
and A/C compressor (X-14) relay OK?

Are the No. SBF-8 fuse (30A) and the No. EB-13
(10A) fuses OK
YES


Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-3) and engine room harness
connector terminal No.2 (X-14)?

Disconnect the A/C compressor relay.

Turn the ignition switch "ON" (Engine is running)


A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.

Is there battery voltage between the engine room harness
connector terminal No.1 (E-3) and ground?
Defective compressor
YESNO
Defective magnetic clutch

HEATER AND AIR CONDITIONING 1-95

MAGNETIC CLUTCH DOES NOT RUN


Replace
YES

Are the A/C thermo (X-15), heater & A/C (X-11)
and A/C compressor (X-14) relay OK?


Are the No. SBF 8 fuse (30A) and the No. EB-13
(10A) fuses OK
YES

Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-2) and engine room
harness connector terminal No.2 (X-14)?


Disconnect the A/C compressor relay.


Turn the ignition switch "ON" (Engine is running)

A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.


Is there battery voltage between the engine room
harness connector terminal No.1 (E-2) and ground?
Defective compressor
YESNO
Defective magnetic clutch

1-100 HEATER AND AIR CONDITIONING



Replace
YES


Are the A/C thermo (X-15), heater & A/C (X-11)
and A/C compressor (X-14) relay OK?


Are the No. SBF 8 fuse (30A) and the No. EB-13
(10A) fuses OK?
YES


Is the pressure switch (C-24) OK?
YES


Are the A/C switch (B-57) and the fan switch (B-13)
OK?
NO
YES


Is there continuity between the engine harness
connector terminal No.1 (E-2) and engine room
harness connector terminal No.2 (X-14)?

Disconnect the A/C compressor relay.


Turn the ignition switch "ON" (Engine is running)


A/C switch and fan control knob (fan switch "ON")
NO
Replace
NO
Defective switch or insufficient
refrigerant
NO
NO
Does the magnetic clutch
operate?
YES
Replace


Disconnect the magnetic clutch connector.

Is there battery voltage between the engine room
harness connector terminal No.1 (E-2) and ground?
Defective compressor
YESNO
Defective magnetic clutch

11A-6 IMMOBILIZER SYSTEM

What happens without proper transponder
operation?
One of the function of transponder is to deactivate or
activate starter function. lf the proper transponder is not
used, starter cannot be operated. Because starter rela
y
stays off, cranking engine is not possible.
After the starter relay is activated, transponder signal
triggers to let lCU calculate by transponder address
signal and immobilizer algorithm.
When the result matches with necessary condition, it
makes injector power source be activated.
If transponder does not send correct signal, lCU and
ECM do not activate injector system on.
Therefore the vehicle cannot be operated.
No proper transponder is available, what
should be done for the system?
When any proper transponder is not available, a new
transponder should be programmed. Up to 5
transponders can be provided with a scan tool (Tech-2)
and by proper procedure.
In addition to the absence of proper transponder, it ma
y
happen particular secret code to the particular vehicle is
missing. ln this case, the secret code must be provided
by your organization.
Otherwise transponder cannot be programmed in an
y
way.
lf the essential for a scan tool (Tech-2) for programming
and proper software for Tech-2 are not available, there
is no permanent way to fix system. Temporary replace
with new ECM, new ICU and new transponder without
any secret code can make the system be deactivated,
but it does not last long. Such a replacement does not
solve any condition. Even after replacement, the system
is activated automatically in short time and then no
operation of the vehicle can be made in any way.
Tech-2 should be provided in your organization.
Caution to the operation
lf an attempt is made to start the engine while the
immobilizer system is activated, the check engine lamp
flashes and the engine will not start.
Summary of operation
Switch on: Set the ignition and starter switch to OFF.
(Activate)
Switch off: Set the ignition and starter switch to ON b
y
using the transponder key. (Deactivate)

What your organization should provide for
your customer





Car Pass

For a new owner, your dealership must hand Car Pass
card, which has identification numbers of new owner's
vehicle immobilizer system. This information is ver
y
important in case of repair or lost of transponder.
The followings are necessary items provided by you
r
responsibility.
1)
Car pass with identification for a new owner
2)
Blank car pass card when it is for reissue
3)
Instruction to dealers how to use car pass card






Security code management

Your organization must keep security codes for all
vehicles as confidential data. Once the security codes
are lost, anybody who have the security code can
access immobilizer system. Your organization has
responsibility of any missing vehicles caused by stolen
security code.






Essential tool (Scan tool : Tech-2)

Your dealership must have Tech-2, and Tech-2 updated
software for immobilizer system.

11A-12 IMMOBILIZER SYSTEM

Pin-outs; For Electronic Control Engine (6VE1, C24SE, 4JH1-TC, 4JA1-TC)
RUW38HSF000201


No. Pin Function
A-1 Antenna coil positive
A-2


A-3 Antenna coil negative
B-1 Starter Relay (6VE1, C24SE Engine) / Immobilizer Relay (4JH1-TC/4JA1-TC Engine)
B-2 Ground
B-3 Voltage from ignition switch ON
B-4 Back up voltage supply
B-5 To Tech-2
B-6 Vehicle speed sensor (6VE1, C24SE Engine) / Not used (4JH1-TC/4JA1-TC Engine)
B-7 Communication: carry on line from ECM to ICU (Check engine lamp)
B-8 Communication: carry on line from ICU to ECM (Communication line W)

11A-14 IMMOBILIZER SYSTEM

Pin-outs




RUW48HSF000201


No. Pin Function
1 Back up voltage supply
2 Voltage from ignition switch ON
3 Lamp
4


5


6 Antenna coil positive
7 Ground
8 Engine immobilizer unit
9 To Tech2
10


11

12


13 Antenna coil negative
14 Starter cut relay

IMMOBILIZER SYSTEM 11A-19

lmportant information on Programming
Security code
The security code protects the immobilizer control unit
against unauthorized programming and data access
from Tech-2. The security code consists of a 4 digit
code number and is programmed into the immobilize
r
control unit and Engine Control Module (ECM).
New control units are not programmed with a securit
y
code.
If the control units are replaced, the security code
entered in the car pass, transponder lD, etc.
Must be programmed into the new control unit with
Tech-2.
The security code can only be programmed with Tech-2
once and must therefore be performed with great care.
Once programmed, the security code cannot be
overwritten. An already used immobilizer can be reused
in a different car by initializing the immobilizer. After that
you can program the security code again. For initializing
command you need the current security code.
If the immobilizer control unit is returned, always
enclosed the security code that is allocated to that
control unit. If this is not done, we can not process the
case and the warranty will not be recognized.
Entering a code
If the Tech-2 display requests that the

security code


mechanical key number


Vehicle Identification No.
be entered, process as follows;
To input a digit you need to use the up and down
buttons of the Tech-2. By using the numeric buttons the
according digit will be displayed at the current position
and the cursor will move to the next position.
For letters you need to use the up and down buttons o
f
the Tech-2. The up and down key might be used for
digits as well. By using the up and down buttons the
displayed digit or letter will be increased or decreased.
To move to the next position you need to use the move-
to-right-button.
With the two buttons, move-to-right and move-to-left
you can select the position of number you want to
change.
This will allow you to correct a wrong number.
After the number is completed you need to press the
Enter button to accept the number. Correction is now no
longer possible.
Use the OKAY soft key to program the number and the
NOT OKAY soft key to abort the programming.
Transponder (Key)





If a transponder key is lost:
If a transponder key is lost, all transponder keys in the
immobilizer control system must be erased.
Transponder keys can be ordered via the "Your prope
r
organization name such as part and accessor
y
department" as previously by providing the mechanical
key number.
The mechanical key number is provided on the ca
r
pass.
Thereafter, existing and new transponder keys are
programmed consecutively using Tech-2. The vehicle
can then no longer be started using lost key.





5 transponder keys can be provided:

Each transponder has different Identifications. If a
customer wants more than 2 transponder keys,
maximum 5 transponder keys can be provided b
y
additional programming by Tech-2.






lf a new ignition key with different mechanical key
number needs to be installed:
If installation of an ignition lock with a different
mechanism key number is necessary (an ignition lock
which belongs to the mechanical key number has to be
ordered first), all transponder keys must first be erased
and the two transponder keys which belong to the
ignition lock that is now installed must be programmed.
The new mechanical key number must be programmed
now into the immobilizer. The mechanical key numbe
r
in the car pass is to be changed as well.
Important:
After successful programming, the engine control can
only be used for vehicles with immobilizer and
transponder.
Faults that occur in connection with the immobilize
r
control unit are recognized by the engine control unit
and as long as "IMMOBILOZER" is not programmed,
are indicated by a flashing of the check engine lamp.
If the immobilizer and engine control unit are replaced
at the same time, the immobilizer control unit must be
programmed first before the "IMMOBILIZER" function in
the engine control unit can be activated.

IMMOBILIZER SYSTEM 11A-21

Tech-2 Features
1.
Tech-2 is a 12volt system. Do not apply 24 volts.
2.
After connecting and/or installing the vehicle
communication interface (VCI) module, PCMCI
A
card and data link connector (DLC) to the Tech-2,
connect the tool to the vehicle DLC.
3.
Make sure the Tech-2 is OFF when removing o
r
installing the PCMCIA card.
4.
The Tech-2 has the capability of two or three
snapshots.
5.
The PCMCIA card is sensitive to magnetism and
static electricity, so care should be taken in the
handling of the card.
6.
The Tech-2 can not plot a graph when replaying a
snapshot.
7.
Always return to the Main Menu by pressing the
EXIT key several times before shutting down.
8.
To clear diagnostic trouble codes (DTCs), open
Application Menu and press "Clear DTC ".

Getting Started
Before operating the Isuzu PCMCIA card with the Tech
2, the following steps must be performed:
1.
The Isuzu System PCMCIA card inserts into the
Tech 2.
2.
Connect the SAE 16/19 adapter to the DLC cable.
3.
Connect the DLC cable to the Tech 2.
4.
Mark sure the vehicle ignition is off.
5.
Connect the Tech 2 SAE 16/19 adapter to the
vehicle DLC.


RHD (For example)
060R300015

6.
Tune on the vehicle ignition (key) switch.
7.
Power the Tech-2 ON and verify the Tech-2 powe
r
up display.

060RW009