2004 ISUZU TF SERIES oil capacity

HEATER AND AIR CONDITIONING 1-15
MAIN DATA AND SPECIFICATIONS

AIR COMPRESSOR

Model CR-14
Type 5 Vane rotary type
Displacement cm3 (lmp fl oz) 144 (4.03)
Oil type DH-PR
Oil capacity cm3 (lmp fl oz) 180 (5.04)
Magnetic clutch Type: Dry single disc dia. 109 mm (4.3 in.)

HEATING UNIT (VENT UNIT)

Type Rehead air mix
Core dimension mm (in.) (L

H

W) 180 (7.06)

182.3 (7.18)

27 (1.06)
Capacity (kcal./hr.) 4200

BLOWER UNIT

Type Sirocco fan type

COOLING UNIT

Type Fin and tube evaporator
Evaporator element dimensions mm (in.) (L

H

W) 230 (9.06)

212 (8.35)

74 (2.91)
Evaporator capacity (kcal./hr.) 2960/4420 kcal./hr. (300/500 m3/hr.)
* Expansion Valve type
External pressure equalizer type
* Thermo Switch type (Cooler)
Variable electronic thermostat

Maximum Cool position (
C)
OFF 3
0.5
DIFF 1.5
0.5

Minimum Cool position (
C)
OFF 11.6 2
DIFF 2.9 2
* Thermo Switch type (A/C) (
C)
Fixed electronic thermostat
OFF 3
0.5
DIFF 1.5
0.5
* Trinary Pressure Switch
Low pressure control and High pressure control are same
as Dual pressure switch
* Medium pressure control
OFF 1128  118 kpa (11.5  1.2 kg/cm
2G)
ON 1521  88 kpa (15.5  0.92 kg/cm2G)
CONDENSER
Type Aluminum louvered fins
Capacity (kcal./hr.) 12300 kcal./hr.

ELECTRIC FAN

Fan Dia
250
Motor Power (w) 90

1-46 HEATER AND AIR CONDITIONING

GENERAL REPAIR PROCEDURE
OIL SPECIFICATION

The HFC-134a system requires a synthetic (PAG)
compressor oil.

Compressor (PAG) oil varies according to compressor
model. Be sure to use oil specified for the model of
compressor.
Specified Compressor Oil
DH-PR



HANDLING OF OIL

The oil should be free from moisture, dust, metal powder,
etc.
 Do not mix with other oil.
 The water content in the oil increases when exposed to the
air. After use, seal oil from air immediately.

The compressor oil must be stored in steel containers, not
in plastic containers.

COMPRESSOR OIL CHECK
The Oil used to lubricate the compressor is circulating with the
refrigerant.
Whenever replacing any component of the system or a large
amount of gas leakage occurs, add oil to maintain the original
amount of. oil.

Oil Capacity

Capacity total in
system CR-14 180 cm3 (5.0 fl.oz.)
Compressor
(Service parts)
charging amount
CR-14
180 cm
3 (5.0 fl.oz.)

1-48 HEATER AND AIR CONDITIONING

Checking and Adjusting for Compressor
Replacement
180 cm3 (5.0 lmp fl oz) of oil is charged in compressor (service
parts). So it is necessary to drain the proper amount of oil from
the new compressor.
1) Perform oil return operation.
2) Discharge refrigerant and remove the compressor.
3) Drain the compressor oil and measure the extracted oil.
4) Check the compressor oil for contamination.
5) Adjust oil level as required.

Amount of oil drained
From used compressor Draining amount of oil
From new compressor
less than
90 cm
3 (2.5 lmp fl oz) Some as drained
amount
more than
90 cm
3 (2.5 lmp fl oz) 90 cm
3 (2.5 lmp fl oz)

6) Evacuate, charge and perform oil return operation.
7) Check system operation.


CONTAMINATION OF COMPRESSOR OIL
Unlike engine oil, no cleaning agent is added to the
compressor oil. Even is the compressor runs for a long period
of time (approximately 1 season), the oil never becomes
contaminated as long as there is nothing wrong with the
compressor or its method of use.
Inspect the extracted oil for any of the following
conditions:
 The capacity of the oil has increased.
 The oil has changed color to red.

Foreign substances, metal powder, etc., are present in the
oil.
If any of these conditions exists, compressor oil is
contaminated. Whenever contaminated compressor oil is
discovered, the receiver/drier must be replaced.

7B-2 MSG MODEL
MAIN DATA AND SPECIFICATIONS

Transmission type Fully synchronized 5-forward gears with a constant
mesh type reverse gear.

Transmission Control Direct control with the gear shift lever on the floor.

Gear ratio MSG5K
1st : 4.122
2nd : 2.493
3rd : 1.504
4th : 1.000
5th : 0.855
Rev : 3.720

Oil capacity lit. (US gal.) 1.55(0.41)

Weight ; approx. kg(lbs) 33.3(73.8)

7B1-50 MANUAL TRANSMISSION

Main Data and Specifications
General Specifications
MUA 5G MUA 5S
Transmission type Fully synchronized forward and reverse gears
Control method Remote control with the gear shift lever on the floor.
Gear ratio: Transmission 1st 4.008 4.357
2nd 2.301 2.502
3rd 1.427 1.501
4th 1.000 1.000
5th 0.828 0.809
Rev. 3.651 3.970
Transmission oil capacity 2.95 lit. (3.12 US qt)
Type of lubricant Engine oil: Refer to the chart in "SECTION 0"

MANUAL TRANSMISSION 7B1-107

Main Data and Specifications
General Specifications

MUA5G MUA5S
Transmission type Fully synchronized forward and reverse gears
Control method Remote control with the gear shift lever on the floor.
Gear ratio: Transmission 1st 4.008 4.357
2nd 2.301 2.502
3rd 1.427 1.501
4th 1.000 1.000
5th 0.828 0.809
Rev. 3.651 3.970
Transmission oil capacity 2.95 lit. (3.12 US qt)
Type of lubricant Engine oil: Refer to the chart in "SECTION 0"

TRANSFER CASE 7D-33

Main Data and Specifications
General Specifications
Type Synchronized type gears shifting between the 2 and 4 wheel drive mode.
Planetary type gears shifting between “low" and “high".
Control method Remote control with the button switch on the instrument panel for gears
shifting among “2H" , “4H" and “4L".
Gear ratio High; 1.000
Low; 2.482
Oil capacity 1.3 lit. (1.37 U.S. quart)
Type of lubricant BESCO GEAR OIL TRANSAXLE (5W-30)
Refer to chart in Section 0

Torque Specifications
Nm (kgm/lb ft)

RTW47DLF000201