2004 INFINITI QX56 fluid

TROUBLE DIAGNOSIS
AT-87
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
56
OthersMaximum speed low.ON vehicle1. Fluid level and stateAT- 5 8
2. Line pressure testAT- 5 9
3. Accelerator pedal position sensorAT- 1 2 9
4. CAN communication lineAT- 1 0 3
5. Direct clutch solenoid valveAT- 1 5 7
6. Control valve with TCMAT- 2 4 1
OFF vehicle7. Torque converterAT- 2 7 3
8. Oil pump assemblyAT- 2 9 0
9. Input clutchAT- 2 9 5
10. Gear systemAT- 2 6 1
11. High and low reverse clutchAT- 3 0 5
12. Direct clutchAT- 3 0 7
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 8
, AT-1 9 .)AT- 2 7 3
14 Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 8
, AT - 1 9
.)AT- 2 7 3
57Extremely large
creep.ON vehicle1. Engine idle speed EC-32

2. CAN communication lineAT- 1 0 3
3. ATF pressure switch 5AT- 1 8 1
OFF vehicle 4. Torque converterAT- 2 7 3
58With selector lever in
“P” position, vehicle
does not enter parking
condition or, with
selector lever in
another position, park-
ing condition is not
cancelled.
Refer to AT- 1 9 3 , "
In
“P” Position, Vehicle
Moves When Pushed"
.ON vehicle1. PNP switchAT- 1 0 9
2. Control cable adjustmentAT- 2 3 4
3. Parking pawl componentsAT- 2 6 1
59Vehicle runs with
transmission in “P”
position.ON vehicle1. PNP switchAT- 1 0 9
2. Fluid level and stateAT- 5 8
3. Control cable adjustmentAT- 2 3 4
4. Control valve with TCMAT- 2 4 1
5. Parking pawl componentsAT- 2 6 1
OFF vehicle 6. Gear systemAT- 2 6 1
No. Items Symptom Condition Diagnostic ItemReference
page

AT-88
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
60
OthersVehicle runs with
transmission in “N”
position.
Refer to AT-194, "In
“N” Position, Vehicle
Moves" .ON vehicle1. PNP switchAT- 1 0 9
2. Fluid level and stateAT-5 8
3. Control cable adjustmentAT- 2 3 4
4. Control valve with TCMAT- 2 4 1
OFF vehicle5. Input clutchAT- 2 9 5
6. Gear systemAT- 2 6 1
7. Direct clutchAT- 3 0 7
8. Reverse brakeAT- 2 7 3
9. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 8
, AT- 1 9 .)AT- 2 7 3
10. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 8
, AT- 1 9
.)AT- 2 7 3
61Engine does not start
in “N” or “P” position.
Refer to AT-192, "Engine Cannot Be
Started In “P” or “N”
Position" .ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 3 4
3. PNP switchAT- 1 0 9
62Engine starts in posi-
tions other than “N” or
“P”.ON vehicle1. Ignition switch and starterPG-4
, SC-
10
2. Control cable adjustmentAT- 2 3 4
3. PNP switchAT- 1 0 9
63 Engine stall.ON vehicle1. Fluid level and stateAT-5 8
2. Engine speed signalAT - 11 5
3. Turbine revolution sensorAT- 1 3 4
4. Torque converter clutch solenoid valveAT - 11 8
5. CAN communication lineAT- 1 0 3
6. Control valve with TCMAT- 2 4 1
OFF vehicle 7. Torque converterAT- 2 7 3
64Engine stalls when
select lever shifted “N”
→ “D”, “R”.ON vehicle1. Fluid level and stateAT-5 8
2. Engine speed signalAT - 11 5
3. Turbine revolution sensorAT- 1 3 4
4. Torque converter clutch solenoid valveAT - 11 8
5. CAN communication lineAT- 1 0 3
6. Control valve with TCMAT- 2 4 1
OFF vehicle 7. Torque converterAT- 2 7 3
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-89
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
65 OthersEngine speed does
not return to idle.
Refer to AT- 2 2 0 ,
"Engine Speed Does
Not Return to Idle" .ON vehicle1. Fluid level and stateAT- 5 8
2. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 8 1,
AT- 1 5 7

3. ATF pressure switch 1 and front brake solenoid valveAT- 1 7 5
,
AT- 1 5 1
4. Accelerator pedal position sensorAT- 1 2 9
5. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 11 2,
AT- 1 3 6
6. CAN communication lineAT- 1 0 3
7. Control valve with TCMAT- 2 4 1
OFF vehicle8. Front brake (brake band)AT- 2 7 39. Direct clutchAT- 3 0 7
No. Items Symptom Condition Diagnostic ItemReference
page

DTC P0615 START SIGNAL CIRCUIT
AT-107
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
5. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 1 0 5 , "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 6.
6. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT - 2 4 1 , "Control Valve With TCM and A/T Fluid
Temperature Sensor 2" .
NG >> Repair or replace damaged parts.

AT-108
DTC P0700 TCM
Revision: August 20072004 QX56
DTC P0700 TCMPFP:31036
DescriptionUCS002DK
The TCM consists of a microcomputer and connectors for signal input and output and for power supply. The
TCM controls the A/T.
On Board Diagnosis LogicUCS002DL

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “TCM” with CONSULT-II or P0700 without CONSULT-II is detected when the
TCM is malfunctioning.
Possible CauseUCS002DM
TCM.
DTC Confirmation ProcedureUCS002DN
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Start engine.
4. Run engine for at least 2 consecutive seconds at idle speed.
5. If DTC is detected, go to AT-108, "
Diagnostic Procedure" .
WITH GST
Follow the procedure “With CONSULT-II”.
Diagnostic ProcedureUCS002DO
1. CHECK DTC
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “SELF DIAG RESULTS” mode for “A/T” with CONSULT-
II.
3. Touch “ERASE”.
4. Turn ignition switch “OFF” and wait at least 10 seconds.
5. Perform DTC Confirmation Procedure, AT - 1 0 8 , "
DTC Confirma-
tion Procedure" .
Is the
“TCM” displayed again?
YES >> Replace the control valve with TCM. Refer to AT-241,
"Control Valve With TCM and A/T Fluid Temperature
Sensor 2" .
NO >>INSPECTION END
BCIA0030E
BCIA0031E

AT-110
DTC P0705 PARK/NEUTRAL POSITION SWITCH
Revision: August 20072004 QX56
Diagnostic ProcedureUCS002DU
1. CHECK PNP SW CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T”
with CONSULT-II.
3. Read out “N·P”, “R” and “D” position switches moving selector
lever to each position.
OK or NG
OK >> GO TO 6.
NG >> GO TO 2.
2. CHECK TCM
Perform TCM input/output signals inspection. Refer to AT- 9 0 , "
TCM Input/Output Signal Reference Values" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 5.
3. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT-109, "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT-241, "Control Valve With TCM and A/T Fluid
Temperature Sensor 2" .
NG >> Repair or replace damaged parts.
5. DETECT MALFUNCTIONING ITEM
Check the following items:

Power supply and ground circuit for TCM.

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
Item name Condition Display value
SLCTLVR POSISelector lever in “N”,“P” position. N/P
Selector lever in “R” position. R
Selector lever in “D” position. D
Selector lever in “4” position. 4
Selector lever in “3” position. 3
Selector lever in “2” position. 2
Selector lever in “1” position. 1
PCIA0034E

DTC P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)
AT-113
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
WITH GST
Follow the procedure “With CONSULT-II”.
Diagnostic ProcedureUCS002E0
1. CHECK INPUT SIGNAL
With CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3. Start the engine.
4. Read out the value of “VHCL/S SE·A/T” while driving.
Check the value changes according to driving speed.
OK or NG
OK >> GO TO 6.
NG >> GO TO 2.
2. CHECK TCM
Perform TCM input/output signals inspection. Refer to AT-90, "
TCM Input/Output Signal Reference Values" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 5.
3. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT- 11 2 , "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 4.
4. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT - 2 4 1 , "Control Valve With TCM and A/T Fluid
Temperature Sensor 2" .
NG >> Repair or replace damaged parts.
5. DETECT MALFUNCTIONING ITEM
Check the following items:

Power supply and ground circuit for TCM.

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> GO TO 6.
NG >> Repair or replace damaged parts.
Item name Condition Display value (km/h)
VHCL/S SE·A/T During driving Approximately matches the
speedometer reading.
SCIA2148E

AT-116
DTC P0725 ENGINE SPEED SIGNAL
Revision: August 20072004 QX56
2. CHECK DTC WITH TCM
With CONSULT-II
1. Start engine.
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for
“A/T” with CONSULT-II.
3. While monitoring engine speed, check for engine speed change
corresponding to wide-open throttle position signal.
With GST
Follow the procedure “With CONSULT-II”.
OK or NG
OK >> GO TO 3.
NG >> Check the ignition signal circuit.

Refer to EC-583, "IGNITION SIGNAL" .
3. CHECK TCM
Perform TCM input/output signals inspection. Refer to AT- 9 0 , "
TCM Input/Output Signal Reference Values" .
OK or NG
OK >> GO TO 4.
NG >> GO TO 6.
4. CHECK DTC
Perform “DTC Confirmation Procedure”.

Refer to AT-115, "DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 5.
5. DETECT MALFUNCTIONING ITEM
Check the following items:

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> Replace the control valve with TCM. Refer to AT-241, "Control Valve With TCM and A/T Fluid
Temperature Sensor 2" .
NG >> Repair or replace damaged parts.
6. DETECT MALFUNCTIONING ITEM
Check the following items:

Power supply and ground circuit for TCM.

The A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
Item name Condition Display value (rpm)
ENGINE SPEED Engine running Closely matches the tachometer reading.
PCIA0041E