2004 INFINITI QX56 relay

GW-2Revision: August 20072004 QX56 Rear Power Window Switch LH or RH Power Supply
and Ground Circuit Check ...................................... 58
Rear Power Window Motor LH Circuit Check ......... 58
Rear Power Window Motor RH Circuit Check ........ 59
Limit Switch Circuit Check Rear LH and RH ........... 60
Encoder Circuit Check Rear LH or RH ................... 62
Power Window Serial Link Check Rear LH or RH ... 64
Rear Power Vent Window Switch Circuit Check ..... 65
Rear Power Vent Window Motor LH Circuit Check ... 65
Rear Power Vent Window Motor RH Circuit Check ... 66
Rear Power Vent Window Relay (OPEN) Check .... 66
Rear Power Vent Window Relay (CLOSE) Check ... 67
FRONT DOOR GLASS AND REGULATOR ............. 69
Removal and Installation ........................................ 69
FRONT DOOR GLASS ....................................... 69
FRONT DOOR GLASS REGULATOR ................ 70
FITTING INSPECTION AND SETTING AFTER
INSTALLATION .................................................... 70
REAR DOOR GLASS AND REGULATOR ............... 72
Removal and Installation ........................................ 72
REAR DOOR GLASS .......................................... 72
REAR DOOR GLASS REGULATOR ................... 73
SIDE WINDOW GLASS ............................................ 75
Removal and Installation ........................................ 75
REMOVAL ........................................................... 75
INSTALLATION .................................................... 75
INSIDE MIRROR ....................................................... 76
Wiring Diagram — I/MIRR — ................................. 76
Removal and Installation ........................................ 77
INSIDE MIRROR ................................................. 77
REAR WINDOW DEFOGGER .................................. 78
Component Parts and Harness Connector Location ... 78
System Description ................................................. 79CAN Communication System Description ..............80
Schematic ...............................................................81
Wiring Diagram — DEF — ......................................82
Terminal and Reference Value for BCM ..................85
Terminal and Reference Value for IPDM E/R ..........85
Work Flow ...............................................................85
CONSULT-II Function (BCM) ..................................86
CONSULT-II BASIC OPERATION PROCEDURE
...86
DATA MONITOR ..................................................87
ACTIVE TEST ......................................................87
Trouble Diagnoses Symptom Chart ........................87
BCM Power Supply and Ground Circuit Check ......89
Rear Window Defogger Switch Circuit Check .........90
Rear Window Defogger Power Supply Circuit
Check ......................................................................91
Rear Window Defogger Circuit Check ....................92
Door Mirror Defogger Power Supply Circuit Check ...92
Door Mirror LH Defogger Circuit Check ..................94
Door Mirror RH Defogger Circuit Check .................95
Rear Window Defogger Signal Check ....................96
Filament Check .......................................................96
Filament Repair .......................................................97
REPAIR EQUIPMENT .........................................97
REPAIRING PROCEDURE .................................97
DOOR MIRROR .........................................................99
Wiring Diagram — MIRROR — ..............................99
Door Mirror Assembly ........................................... 100
REMOVAL .......................................................... 100
INSTALLATION .................................................. 100
Door Mirror Glass .................................................. 100
REMOVAL .......................................................... 100
INSTALLATION .................................................. 101

POWER WINDOW SYSTEM
GW-15
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: August 20072004 QX56
POWER WINDOW SYSTEMPFP:25401
Component Parts and Harness Connector LocationEIS002UM
System DescriptionEIS002UN
Power is supplied at all time

from 50A fusible link (letter f , located in the fuse and fusible link box)

to BCM terminal 70

through BCM terminal 69

to main power window and door lock/unlock switch terminal 19

to power window and door lock/unlock switch RH terminal 10.
With ignition switch in ON or START position,
Power is supplied

through 10A fuse (No. 59, located in the fuse and relay box)

to BCM terminal 38

through BCM terminal 68

to main power window and door lock/unlock switch terminal 10.

to rear power vent window relays (OPEN and CLOSE) terminal 1.
With ignition switch in ON or START position,
Ground is supplied

to BCM terminal 67

to main power window and door lock/unlock switch terminal 17

to power window and door lock/unlock switch RH terminal 11

through body grounds M57, M61 and M79.
LIIA1890E

POWER WINDOW SYSTEM
GW-17
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: August 20072004 QX56

to rear power window control unit LH or RH terminal 1

through rear power window control unit LH or RH terminal 7

through rear power window switch LH or RH terminal 2 and 3

through rear power window switch LH or RH terminal 5

through rear power window control unit LH or RH terminal 11

to rear power window motor LH or RH terminal 2.
Ground is supplied

to rear power window control unit LH or RH terminal 15

through rear power window control unit LH or RH terminal 16

through rear power window switch LH or RH terminal 1 and 7

through rear power window switch LH or RH terminal 4

through rear power window control unit LH or RH terminal 12

to rear power window motor LH or RH terminal 1.
Then, the motor raises the window until the switch is released.
WINDOW DOWN
When the rear power window switch LH or RH is pressed in the down position
Power is supplied

to rear power window control unit LH or RH terminal 1

through rear power window control unit LH or RH terminal 7

through rear power window switch LH or RH terminal 2 and 3

through rear power window switch LH or RH terminal 4

through rear power window control unit LH or RH terminal 12

to rear power window motor LH or RH terminal 1.
Ground is supplied

to rear power window control unit LH or RH terminal 15

through rear power window control unit LH or RH terminal 16

through rear power window switch LH or RH terminal 1 and 7

through rear power window switch LH or RH terminal 5

through rear power window control unit LH or RH terminal 11

to rear power window motor LH or RH terminal 2.
Then, the motor lowers the window until the switch is released.
MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OPERATION
Signal is sent

through main power window and door lock/unlock switch terminal 14

to rear power window control unit LH or RH terminal 1.
The operation of power window after receiving the signal is the same as operating the power window with rear
power window switch LH or RH.
VENT WINDOW CLOSE
When the rear power vent window switch is pressed in the close position
Power is supplied

to rear power vent window relay (CLOSE) terminal 5

through rear power vent window relay (CLOSE) terminal 3

to rear power vent window motors terminal 2.
Ground is supplied

to rear power vent window relay (OPEN) terminal 4

through rear power vent window relay (OPEN) terminal 3

to rear power vent window motors terminal 1.
Then, the motors close the windows until the switch is released.
VENT WINDOW OPEN
When the main power window and door lock/unlock switch (rear LH) is pressed in the open position
Power is supplied

GW-18
POWER WINDOW SYSTEM
Revision: August 20072004 QX56

to rear power vent window relay (OPEN) terminal 5

through rear power vent window relay (OPEN) terminal 3

to rear power vent window motors terminal 1.
Ground is supplied

to rear power vent window relay (CLOSE) terminal 4

through rear power vent window relay (CLOSE) terminal 3

to rear power vent window motors terminal 2.
Then, the motors open the windows until the switch is released.
AUTO OPERATION
The power window AUTO feature enables the driver to open or close the window without holding the window
switch in the down or up position.
POWER WINDOW SERIAL LINK
Main power window and door lock/unlock switch, power window and door lock/unlock switch RH, rear power
window control units and BCM transmit and receive the signal by power window serial link.
The signal is transmitted from BCM to main power window and door lock/unlock switch and power window and
door lock/unlock switch RH

Keyless power window down signal.

Rear power window switch illumination.
The signal is transmitted from main power window and door lock/unlock switch to power window and door
lock/unlock switch RH

Front door window RH operation signal.

Power window control by front door lock assembly LH (key cylinder switch) signal.

Power window lock signal.

Retained power operation signal.

Rear power window operation.
POWER WINDOW LOCK
The power window lock is designed to lock operation of all windows except for front door window LH.
When in the lock position, the power window lock signal is transmitted to power window and door lock/unlock
switch RH by power window serial link. This prevents the power window motor from operating.
RETAINED POWER OPERATION
When the ignition switch is turned to the OFF position from ON or START position.
Power is supplied for 45 seconds

to main power window and door lock/unlock switch terminal 10

from BCM terminal 68.
When power and ground are supplied, the BCM continues to be energized, and the power window can be
operated.
The retained power operation is canceled when the front LH or front RH door is opened.
RAP signal period can be changed by CONSULT-II. Refer to GW-33, "
CONSULT-II Function (BCM)" .
ANTI-PINCH SYSTEM
Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and rear
power window control unit LH and RH monitors the power window motor operation and the power window
position (full closed or other) for each power window by the signals from encoder and limit switch in power win-
dow motor.
When a window switch detects interruption during the following close operation,

automatic close operation when ignition switch is in the ON position

automatic close operation during retained power operation
Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and rear
power window control unit LH and RH controls each power window motor for open and the power window will
be lowered about 150 mm (5.91 in).

GW-36
POWER WINDOW SYSTEM
Revision: August 20072004 QX56
Trouble Diagnoses Symptom ChartEIS0 02 UW

Check that other systems using the signal of the following systems operate normally.
Symptom Repair order Refer to page
None of the power windows can be operated using any switch1. BCM power supply and ground circuit checkGW-38
2. Main power window and door lock/unlock
power supply and ground circuit checkGW-39
3. Power window serial link check front LH and
RHGW-40
Front power window LH alone does not operate1. Main power window and door lock/unlock
power supply and ground circuit checkGW-392. Front power window motor LH circuit checkGW-41
3. Replace main power window and door lock/
unlock switchEI-31
Front power window RH alone does not operate1. Power window and door lock/unlock switch
RH power supply and ground circuit checkGW-402. Power window serial link check front LH and
RHGW-54
3. Front power window motor RH circuit checkGW-42
4. Replace BCMBCS-19
Rear power window LH alone does not operate1. Rear power window control unit LH or RH
power supply and ground circuit checkGW-56
2. Rear power window switch LH or RH power
supply and ground circuit checkGW-58
3. Rear power window motor LH circuit checkGW-58
4. Power window serial link check rear LH and
RHGW-64
5. Replace BCMBCS-19
Rear power window RH alone does not operate1. Rear power window control unit LH or RH
power supply and ground circuit checkGW-56
2. Rear power window switch LH or RH power
supply and ground circuit checkGW-58
3. Rear power window motor RH circuit checkGW-59
4. Power window serial link check rear LH and
RHGW-64
5. Replace BCMBCS-19
Rear power vent windows do not operate 1. Rear power vent window switch circuit checkGW-65
Rear power vent window LH alone does not operate1. Rear power vent window motor LH circuit
checkGW-65
Rear power vent window RH alone does not operate1. Rear power vent window motor RH circuit
checkGW-66
Rear power vent windows do not open1. Rear power vent window relay (OPEN)
checkGW-65
Rear power vent windows do not close1. Rear power vent window relay (CLOSE)
checkGW-65

GW-38
POWER WINDOW SYSTEM
Revision: August 20072004 QX56
BCM Power Supply and Ground Circuit CheckEIS002UX
1. CHECK FUSE AND FUSIBLE LINK
Check 50A fusible link (letter f located in the fuse and fusible link box).
Check 10A fuse (No. 59, located in the fuse and relay box).
NOTE:
Refer to GW-15, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
3, "PRECAUTIONS" .
2. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between BCM connector M18, M20 terminals 11, 38, 70 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM.
3. Check continuity between BCM connector M20 terminal 67 and ground.
OK or NG
OK >> Power supply and ground circuit is OK.
NG >> Repair or replace harness.11 (O) - Ground : Battery voltage
38 (W/L) - Ground : Battery voltage
70 (W/B) - Ground : Battery voltage
WIIA0504E
67 (B) - Ground : Continuity should exist.
LIIA0915E

GW-66
POWER WINDOW SYSTEM
Revision: August 20072004 QX56
Rear Power Vent Window Motor RH Circuit CheckEIS002VD
1. CHECK REAR POWER VENT WINDOW SWITCH RH SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power vent window motor RH.
3. Turn ignition switch ON.
4. Check voltage between rear power vent window motor RH connector B150 terminal 1, 2 and ground.
OK or NG
OK >> Replace rear power vent window motor RH.
NG >> Repair or replace harness.
Rear Power Vent Window Relay (OPEN) CheckEIS002VE
1. CHECK REAR POWER VENT WINDOW RELAY (OPEN) POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear power vent window relay (OPEN).
3. Turn ignition switch ON.
4. Check voltage between rear power vent window relay (OPEN) connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK REAR POWER VENT WINDOW RELAY (OPEN)
Check continuity between rear power vent window relay (OPEN) terminals 3 and 4, 3 and 5.
OK or NG
OK >> GO TO 3.
NG >> Replace rear power vent window relay (OPEN).
ConnectorTerminals (Wire color)
ConditionVoltage (V)
(Approx.)
(+) (-)
B1501 (BR)
GroundOpening Battery voltage
Closing 0
2 (R)Opening 0
Closing Battery voltage
WIIA0290E
ConnectorTerminals (Wire color)
Voltage (V)
(Approx.)
(+) (-)
M871 (W/L)
Ground Battery voltage
5 (W/R)
LIIA1565E
Terminal Condition Continuity
3412V direct current supply
between terminals 1 and 2No
No current supply Yes
3512V direct current supply
between terminals 1 and 2Ye s
No current supply No
WIIA0291E

POWER WINDOW SYSTEM
GW-67
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: August 20072004 QX56
3. CHECK REAR POWER VENT WINDOW RELAY (OPEN) GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between rear power vent window relay (OPEN)
connector M87 terminal 4 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK REAR POWER VENT WINDOW RELAY (OPEN) CIRCUIT
1. Disconnect rear power vent window switch.
2. Check continuity between rear power vent window relay (OPEN)
connector M87 terminal 2 and rear power vent window switch
connector R103 terminal 3.
OK or NG
OK >> Replace rear power vent window switch.
NG >> Repair or replace harness.
Rear Power Vent Window Relay (CLOSE) CheckEIS002VF
1. CHECK REAR POWER VENT WINDOW RELAY (CLOSE) POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear power vent window relay (CLOSE).
3. Turn ignition switch ON.
4. Check voltage between rear power vent window relay (CLOSE) connector and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.4 (B) - Ground : Continuity should exist.
LIIA1567E
2 (G/R) - 3 (BR/W) : Continuity should exist.
LIIA1568E
ConnectorTerminals (Wire color)
Voltage (V)
(Approx.)
(+) (-)
M891 (W/L)
Ground Battery voltage
5 (W/R)
LIIA1565E