2004 INFINITI QX56 Vdc

ACS-1
AUTO CRUISE CONTROL SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION ACS
A
B
ACS
Revision: August 20072004 QX56
ASCD
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ..... 3
Description ............................................................... 3
ICC
PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
Precautions for ICC System Service ........................ 4
Wiring Diagrams and Trouble Diagnosis .................. 4
PREPARATION ........................................................... 5
Special Service Tool ................................................. 5
DESCRIPTION ............................................................ 6
Outline ...................................................................... 6
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE ................................................................... 6
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ................................................. 6
BRAKE ASSIST (WITH PREVIEW FUNCTION) ..... 6
System Diagram ....................................................... 7
Components Description .......................................... 7
CAN Communication ................................................ 7
SYSTEM DESCRIPTION ...................................... 7
Switch Operation ...................................................... 8
ICC System Display ................................................. 8
ACTION TEST ............................................................ 9
ICC System Running Test ........................................ 9
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE ................................................................... 9
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ............................................... 10
LASER BEAM AIMING ADJUSTMENT ................... 12
Outline of Laser Beam Aiming Adjustment Proce-
dure ........................................................................ 12
Preparation ............................................................. 12
Setting up the ICC Target Board ............................ 12
ADJUSTING HEIGHT OF THE ICC TARGET
BOARD ............................................................... 12ADJUSTING THE POSITION OF THE ICC TAR-
GET BOARD STRING ......................................... 13
POSITIONING THE ICC TARGET BOARD ........ 13
Sensor Adjustment ................................................. 14
CHECK AFTER THE ADJUSTMENT .................. 17
ELECTRICAL UNITS LOCATION ............................ 18
Component Parts and Harness Connector Location ... 18
WIRING DIAGRAM ................................................... 19
Schematic ............................................................... 19
Wiring Diagram — ICC — ...................................... 20
TERMINALS AND REFERENCE VALUE ................. 25
Terminals and Reference Values for ICC Unit ........ 25
Terminals and Reference Values for ICC Sensor ... 25
TROUBLE DIAGNOSIS — GENERAL DESCRIP-
TION .......................................................................... 26
Work Flow ............................................................... 26
CONSULT-II Function (ICC) ................................... 27
CONSULT-II OPERATION ................................... 27
WORK SUPPORT ............................................... 28
SELF-DIAGNOSTIC RESULTS ........................... 28
DATA MONITOR ................................................. 29
ACTIVE TEST ..................................................... 30
Self-Diagnostic Function ......................................... 32
WITH CONSULT-II .............................................. 32
WITHOUT CONSULT-II ....................................... 32
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY
WILL NOT RUN ................................................... 34
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 36
Diagnostic Trouble Code (DTC) Chart ................... 36
DTC 11 CONTROL UNIT ....................................... 37
DTC 12 VDC CONTROL UNIT ............................... 37
DTC 20 CAN COMM CIRCUIT ............................... 38
DTC 31 POWER SUPPLY CIR 1, DTC 34 POWER
SUPPLY CIR 2 ....................................................... 38
DTC 41 VHCL SPEED SE CIRC ............................ 39
DTC 43 VDC/TCS/ABS CIRC ................................ 39
DTC 45 BRAKE SW/STOP L SW ........................... 40
DTC 46 OPERATION SW CIRC ............................. 41
DTC 74 LASER BEAM OFF CENTER ................... 42

ACS-28
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: August 20072004 QX56
6. Touch “WORK SUPPORT”, “SELF-DIAG RESULTS”, “DATA
MONITOR”, "CAN DIAG SUPPORT MNTR", “ACTIVE TEST” or
“ECU PART NUMBER” on selection screen.
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT” on the "SELECT DIAG MODE"
screen.
2. Touch “CAUSE OF AUTO-CANCEL” on the "SELECT WORK
ITEM screen.
3. Cause of automatic cancellation screen will be shown.
4. The last five causes of automatic cancellation of ICC system will
be displayed.
Possible Causes of "Auto-Cancel"
Laser Beam Adjust
For details, refer to ACS-12, "LASER BEAM AIMING ADJUSTMENT" .
SELF-DIAGNOSTIC RESULTS
For details, refer to ACS-36, "Diagnostic Trouble Code (DTC) Chart" .
WKIA2041E
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
OPE SW VOLT CIRC Voltage outside the standard was detected.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
NO RECORD —

ACS-36
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: August 20072004 QX56
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMSPFP:00000
Diagnostic Trouble Code (DTC) ChartEKS007X2
×:Applicable
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake
assist
(with pre-
view
function)
11 CONTROL UNIT××××

ICC unit internal malfunctionACS-37
12 VDC CONTROL UNIT××××

VDC malfunction

Brake booster signal harness is
open or shortedACS-37
20 CAN COMM CIRCUIT××××
ICC unit detected CAN communi-
cation malfunctionACS-38
31 POWER SUPPLY CIR1××××
ICC unit power supply voltage is
excessively low (less than 8V)ACS-38
34 POWER SUPPLY CIR2××××
ICC unit power supply voltage is
excessively high.ACS-38
41 VHCL SPEED SE CIRC××××

Wheel sensor malfunction

ABS actuator and electric unit
(control unit) malfunction

AT vehicle speed sensor mal-
function

TCM malfunctionACS-39
43 VDC/TCS/ABS CIRC××××
VDC/TCS/ABS system malfunc-
tionACS-39
45 BRAKE SW/ STOP L SW××××

ICC brake switch or stop lamp
switch harness is open or shorted

ICC brake switch or stop lamp
switch is stuck to OFF

ICC brake switch or stop lamp
switch is stuck to ONACS-40
46 OPERATION SW CIRC×××

ICC steering switch harness or
spiral cable is open or shorted

ICC steering switch malfunctionACS-41
74 LASER BEAM OFF CNTR×× ×
Laser beam of ICC sensor is off
the aiming pointACS-42
90 STOP LAMP RLY FIX×× ×
Normally open terminal of stop
lamp relay is stuckACS-43
92 ECM CIRCUIT××××

ECM malfunction

Accelerator pedal position sensor
malfunction

ICC unit malfunctionACS-47
96 NP RANGE×××

Park/neutral position switch har-
ness is open or shorted

Park/neutral position switch mal-
function

TCM malfunctionACS-48
97 AT CIRCUIT××
TCM malfunctionACS-48

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-37
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
DTC 11 CONTROL UNITEKS007X3
1. DIAGNOSTIC CHECK
1. Are any items other than “DTC 11 CONTROL UNIT” indicated on self-diagnosis display?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> Replace ICC unit. Refer to ACS-59, "
ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again.
DTC 12 VDC CONTROL UNITEKS008DH
1. DIAGNOSIS CHECK
With CONSULT-II

Perform self-diagnosis of ABS actuator and electric unit (control unit). Is malfunction indicated?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then per-
form self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK CONNECTOR ICC UNIT AND ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
1. Turn ignition switch OFF.
2. Disconnect connectors of ICC unit and ABS actuator and electric unit (control unit), and connect them
securely again. Then erase DTC. Then, perform self-diagnosis of ICC system again.
OK or NG
OK >> Poor connector connection. Check connector housing for disconnected, loose, bent and col-
lapsed terminals. If any malfunction is detected, repair applicable part. After repair, erase DTC
and perform ICC system running test. Then perform self-diagnosis of ICC system again.
NG >> GO TO 3.
98 GEAR POSITION××

TCM malfunction

AT turbine revolution sensor mal-
function

AT vehicle speed sensor mal-
functionACS-49
102 LASER STAIN×× ×
ICC sensor body window has
contaminationACS-49
103 LASER SENSOR FAIL×× ×
ICC sensor internal malfunctionACS-50
104 LASER AIMING INCMP×× ×
Laser beam aiming of ICC sensor
is not adjustedACS-50
107 LASER COMM FAIL×× ×

CAN data received by ICC sen-
sor is strange (from ICC unit,
combination meter or ECM)ACS-51
109 LASER HIGH TEMP×× ×
Temperature around ICC sensor
is excessively highACS-51
DTC
No.CONSULT-II screen termsICC sys-
tem
warning
lampFail-safe
Malfunctions detected where...Refer-
ence
page Vehicle-
to-vehi-
cle dis-
tance
control
modeConven-
tional
(fixed
speed)
cruise
control
modeBrake
assist
(with pre-
view
function)

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-39
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
3. CHECK GROUND CIRCUIT FOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connectors.
3. Check continuity between ICC unit harness connector B13 ter-
minal 19 (B), 20 (B), B17 terminal 46 (B) and ground.
OK or NG
OK >> Replace ICC unit, Refer to ACS-59, "ICC Unit" . Erase
DTC, and perform ICC system running test. Then per-
form self-diagnosis of ICC system again.
NG >>

Repair ICC unit ground harness.

After repair, erase DTC and perform ICC system running test. Then perform self-diagnosis of
ICC system again.
DTC 41 VHCL SPEED SE CIRCEKS007X6
1. PERFORM ICC UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis. Is “DTC 43 VDC/TCS/ABS CIRC” or “DTC 20 CAN COMM CIRCUIT” indicated in
self-diagnosis item display?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK AT VEHICLE SPEED SENSOR
With CONSULT-II

With data monitor, check “VHCL SPD AT”.
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again.
NG >>

Check TCM.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 43 VDC/TCS/ABS CIRCEKS007X7
1. DIAGNOSIS CHECK 1
With CONSULT-II

Perform self-diagnosis. Is “CAN COMM CIRCUIT” indicated?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> GO TO 2.
2. DIAGNOSIS CHECK 2
With CONSULT-II

Perform self-diagnosis of ABS actuator and electric unit (control unit). Is malfunction indicated?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> Replace ICC unit. Refer to ACS-59, "
ICC Unit" . Erase DTC and perform ICC system running
test. Then perform self-diagnosis of ICC system again. Continuity should exist.
SKIA6650E

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-49
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: August 20072004 QX56
DTC 98 GEAR POSITIONEKS007XJ
1. DIAGNOSTIC CHECK
With CONSULT-II

Is “DTC 43 VDC/TCS/ABS CIRC” or “DTC 41 VHCL SPEED SE CIRC” indicated in self-diagnosis display
item?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform self-diagnosis of ICC system again.
NO >> GO TO 2.
2. CHECK VEHICLE SPEED SIGNAL
With CONSULT-II

With data monitor, check that “VHCL SPEED SE” is normal.
OK or NG
OK >> GO TO 3.
NG >> Replace ICC unit. Refer to ACS-59, "
ICC Unit" . Erase DTC and perform self-diagnosis of ICC
system again.
3. CHECK SHIFT GEAR POSITION

Check that gear positions are correct in A/T.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
4. CHECK TCM GEAR POSITION SIGNAL
With CONSULT-II

With TCM data monitor with CONSULT-II, check that gear positions are correct.
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform self-diagnosis of ICC
system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
5. CHECK TCM TURBINE ROTATION
With CONSULT-II

With TCM diagnosis, check that turbine rpm is normal. Refer to AT-134, "DTC P1716 TURBINE REVOLU-
TION SENSOR" .
OK or NG
OK >> Replace ICC unit. Refer to ACS-59, "ICC Unit" . Erase DTC and perform self-diagnosis of ICC
system again.
NG >>

Perform TCM diagnosis.

After repair, erase DTC and perform self-diagnosis of ICC system again.
DTC 102 LASER STAINEKS007XK
1. VISUAL INSPECTION (1)

Check that there is no contamination and foreign material on ICC sensor body window.
OK or NG
OK >> GO TO 2.
NG >>

Clean ICC sensor.

Erase DTC and perform ICC system running test. Then perform self-diagnosis of ICC system
again.

BRC-1
BRAKE CONTROL SYSTEM
F BRAKES
CONTENTS
C
D
E
G
H
I
J
K
L
M
SECTION BRC
A
B
BRC
Revision: August 20072004 QX56VDC/TCS/ABS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Brake System .................................. 3
Precautions When Using CONSULT-II ..................... 3
CHECK POINTS FOR USING CONSULT-II ......... 3
Precautions for Brake Control .................................. 4
Precautions for CAN System ................................... 4
Wiring Diagrams and Trouble Diagnosis .................. 5
PREPARATION ........................................................... 6
Special Service Tool ................................................. 6
Commercial Service Tools ........................................ 6
SYSTEM DESCRIPTION ............................................ 7
System Components ................................................ 7
ABS Function ........................................................... 8
EBD Function ........................................................... 8
TCS Function ........................................................... 8
VDC Function ........................................................... 8
Fail-Safe Function .................................................... 8
ABS/EBD SYSTEM ............................................... 9
VDC/TCS SYSTEM ............................................... 9
ACTIVE BOOSTER ............................................... 9
Hydraulic Circuit Diagram ........................................ 9
CAN COMMUNICATION .......................................... 10
System Description ................................................ 10
TROUBLE DIAGNOSIS .............................................11
How to Perform Trouble Diagnoses for Quick and
Accurate Repair ......................................................11
INTRODUCTION ..................................................11
WORK FLOW ...................................................... 12
CLARIFY CONCERN .......................................... 13
EXAMPLE OF DIAGNOSIS SHEET ................... 13
Component Parts and Harness Connector Location ... 14
Schematic .............................................................. 15
Wiring Diagram — VDC — ..................................... 16
Basic Inspection ..................................................... 23
BRAKE FLUID LEVEL, FLUID LEAK, AND
BRAKE PAD INSPECTION ................................. 23POWER SYSTEM TERMINAL LOOSENESS
AND BATTERY INSPECTION ............................. 23
ABS WARNING LAMP, SLIP INDICATOR LAMP
AND VDC OFF INDICATOR LAMP INSPECTION ... 23
Warning Lamp and Indicator Timing ....................... 24
Control Unit Input/Output Signal Standard ............. 24
REFERENCE VALUE FROM CONSULT-II ......... 24
CONSULT-II Function (ABS) .................................. 28
CONSULT-II BASIC OPERATION PROCEDURE
... 28
SELF-DIAGNOSIS .............................................. 29
DATA MONITOR ................................................. 32
ACTIVE TEST ..................................................... 36
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ........................................................................ 38
Wheel Sensor System Inspection ........................... 38
Engine System Inspection ...................................... 39
ABS/TCS/VDC Control Unit Inspection .................. 40
Steering Angle Sensor System ............................... 40
Yaw Rate/Side/Decel G Sensor System Inspection ... 41
Solenoid and VDC Change-Over Valve System
Inspection ............................................................... 43
Actuator Motor, Motor Relay, and Circuit Inspection ... 44
Stop Lamp Switch System Inspection .................... 45
ABS/TCS/VDC Control Unit Power and Ground
Systems Inspection ................................................ 46
Brake Fluid Level Switch System Inspection .......... 47
Active Booster System Inspection .......................... 48
Delta Stroke Sensor System Inspection ................. 49
Pressure Sensor System Inspection ...................... 51
Steering Angle Sensor Safe Mode Inspection ........ 53
CAN Communication System Inspection ................ 54
ICC System Inspection ........................................... 54
Inspection For Self-diagnosis Result "ST ANGLE
SEN SIGNAL" ......................................................... 55
Inspection For Self-diagnosis Result "DECEL G
SEN SET" ............................................................... 55
VDC OFF Indicator lamp Does Not Illuminate ........ 55
Component Inspection ............................................ 56
VDC OFF SWITCH ............................................. 56

BRC-2Revision: August 20072004 QX56 TROUBLE DIAGNOSES FOR SYMPTOMS ............. 57
ABS Works Frequently ........................................... 57
Unexpected Pedal Action ....................................... 58
Long Stopping Distance .......................................... 59
ABS Does Not Work ............................................... 59
Pedal Vibration or ABS Operation Noise ................ 59
ABS Warning Lamp Does Not Come On When Igni-
tion Switch Is Turned On ........................................ 60
ABS Warning Lamp Stays On When Ignition Switch
Is Turned On ........................................................... 60
Vehicle Jerks During TCS/VDC Activation .............. 61
ON-VEHICLE SERVICE ............................................ 62
Adjustment of Steering Angle Sensor Neutral Posi-
tion .......................................................................... 62
Calibration of Decel G Sensor ................................ 62WHEEL SENSORS ...................................................64
Removal and Installation .........................................64
REMOVAL ............................................................64
INSTALLATION ....................................................64
SENSOR ROTOR ......................................................65
Removal and Installation .........................................65
ACTUATOR AND ELECTRIC UNIT (ASSEMBLY) ... 66
Removal and Installation .........................................66
REMOVAL ............................................................66
INSTALLATION ....................................................67
STEERING ANGLE SENSOR ...................................68
Removal and Installation .........................................68
G SENSOR ................................................................69
Removal and Installation .........................................69
REMOVAL ............................................................69
INSTALLATION ....................................................69