2004 INFINITI FX35 control

AV-168
NAVIGATION SYSTEM
Revision: 2004 November 2004 FX35/FX45
Operating Screen for Audio and A/C is Not Displayed When Showing NAVI
Screen
AKS00BNX
1. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect display control unit connector and display connector.
3. Check continuity between display control unit harness connector
terminals and display harness connector terminals.
4. Check continuity between display control unit harness connector
M76 terminals 49, 53 (W), 55 (R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK VERTICAL SYNCHRONIZING SIGNAL
1. Connect display control unit connector and display connector.
2. Turn ignition switch ON.
3. Check signal between display control unit harness connector
M76 terminals 53 (W) and 49 with CONSULT-ll or oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> Replace display.
Terminals
Continuity Display control unit Display
ConnectorTe r m i n a l
(Wire color)ConnectorTerminal
(Wire color)
M7649
M6321
Ye s 53 (W) 20 (W)
55 (R) 8 (R)
SKIB0480E
49, 53, 55 – Ground : Continuity should not exist.
SKIB0481E
53 – 49 : Refer to AV- 1 2 3 , "Terminals
and Reference Value for Dis-
play Control Unit" .
SKIA9506E

NAVIGATION SYSTEM
AV-169
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
3. CHECK HORIZONTAL SYNCHRONIZING SIGNAL
1. Check signal between display control unit harness connector
M76 terminals 55 (R) and 49 with CONSULT-ll or oscilloscope.
OK or NG
OK >> Replace display control unit.
NG >> Replace display.
TRIP, FUEL ECON and MAINTENANCE Screens are Not ShownAKS00BNY
1. CHECK IGNITION SIGNAL
Check ignition signal. Refer to AV- 1 5 2 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.
2. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check power supply circuit for display. Refer to AV- 1 4 7 , "
Power Supply and Ground Circuit Check for Display"
.
OK or NG
OK >> GO TO 3.
NG >> Repair malfunctioning parts.
3. CHECK COMMUNICATION LINE
Check display communication line. Refer to AV- 1 5 6 , "
When Malfunctioning Connection Between Display Con-
trol Unit and Display" .
OK or NG
OK >> Replace display.
NG >> Check the malfunctioning parts.
Average Fuel Economy Displayed is Not Shown (“***” is Shown)AKS00BNZ
1. CHECK VEHICLE SPEED SIGNAL
Check vehicle speed signal. Refer to AV- 1 5 0 , "
Vehicle Speed Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.
2. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 5 8 , "
CAN Communication Line Check" .
OK or NG
OK >> GO TO 3.
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-4, "
Precautions When
Using CONSULT-II" . 55 – 49 : Refer to AV- 1 2 3 , "
Te r m i n a l s
and Reference Value for Dis-
play Control Unit" .
PKIA2888E

AV-170
NAVIGATION SYSTEM
Revision: 2004 November 2004 FX35/FX45
3. CHECK COMMUNICATION LINE
Check display communication line. Refer to AV- 1 5 6 , "
When Malfunctioning Connection Between Display Con-
trol Unit and Display" .
OK or NG
OK >> Replace display.
NG >> Repair malfunctioning parts.
Driving Distance or Average Speed is Not Shown (“***” is Shown) AKS00BO0
1. CHECK IGNITION SIGNAL FOR DISPLAY CONTROL UNIT
Check ignition signal for display cntrol unit. Refer to AV- 1 5 2 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.
2. CHECK VEHICLE SPEED SIGNAL FOR DISPLAY CONTROL UINIT
Check vehicle speed signal for display control unit. Refer to AV- 1 5 0 , "
Vehicle Speed Signal Check for Display
Control Unit" .
OK or NG
OK >> Replace display control unit.
NG >> Repair malfunctioning parts.
WARNING DOOR OPEN Screen is Not ShownAKS00BO1
1. CHECK IGNITION SIGNAL FOR DISPLAY CONTROL UNIT
Check ignition signal for display control unit. Refer to AV- 1 5 2 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.
2. CHECK VEHICLE SPEED SIGNAL FOR DISPLAY CONTROL UNIT
Check vehicle speed signal for display control unit. Refer to AV- 1 5 0 , "
Vehicle Speed Signal Check for Display
Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.
3. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 5 8 , "
CAN Communication Line Check" .
OK or NG
OK >> GO TO 3.
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-4, "
Precautions When
Using CONSULT-II" .
TIRE PRESSURE Screen is not ShownAKS00BO2
1. CHECK LOW TIRE PRESSURE WARNING CONTROL UNIT
Check low tire pressure warning control unit. Refer to WT-17, "
Self-Diagnosis" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.

NAVIGATION SYSTEM
AV-171
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
2. CHECK IGNITION SIGNAL FOR DISPLAY CONTROL UNIT
Check ignition signal for display control unit. Refer to AV- 1 5 2 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 3.
NG >> Repair malfunctioning parts.
3. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 5 8 , "
CAN Communication Line Check" .
OK or NG
OK >> GO TO 3.
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-4, "
Precautions When
Using CONSULT-II" .
Unable to Operate All of A/C and AV switch (Unable to start Self-Diagnosis)AKS00BO3
1. A/C AND AV SWITCH SELF-DIAGNOSIS
Start A/C and AV switch self-diagnosis. Refer to AV- 1 4 4 , "
A/C and AV Switch Self-Diagnosis Function" .
OK or NG
OK >> GO TO 3.
NG >> GO TO 2.
2. CHECK A/C AND AV SWITCH POWER SUPPLY AND GROUND CIRCUIT
Check A/C and AV switch power supply and ground circuit. Refer to AV- 1 4 9 , "
Power Supply and Ground Cir-
cuit Check for A/C and AV Switch" .
OK or NG
OK >> Replace A/C and AV switch.
NG >> Repair malfunctioning parts.
3. CHECK DISPLAY CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Check display control unit power supply and ground circuit. Refer to AV- 1 4 6 , "
Power Supply and Ground Cir-
cuit Check for Display Control Unit" .
OK or NG
OK >> GO TO 4.
NG >> Repair malfunctioning parts.
4. CHECK A/C AND AV SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect display control unit connector and A/C and AV switch connector.
3. Check continuity between display control unit harness connector
M76 terminals 28 (B/R), 30 (W/R) and A/C and AV switch har-
ness connector M64 terminals 6 (B/R), 8 (W/R).
4. Check continuity between display control unit connector M76
terminals 28 (B/R), 30 (W/R) and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.28 – 6 : Continuity shold exist.
30 – 8 : Continuity shold exist.PKIA2885E

AV-172
NAVIGATION SYSTEM
Revision: 2004 November 2004 FX35/FX45
5. CHECK A/C AND AV SWITCH CIRCUIT
1. Replace A/C and AV switch.
2. Connect display control unit connector and A/C and AV switch connector.
3. Turn ignition switch ON.
4. Start self-diagnosis of DCU, and check the self-diagnosis result.
OK or NG
OK >> INSPECTION END
NG >> Peplace display control unit.
Position of Current-Location Mark is Not CorrectAKS00BO4
1. SELF-DIAGNOSIS
“Self-diagnosis mode” of the self-diagnosis function. Refer to AV- 1 3 3 , "
Self-Diagnosis Mode (NAVI)" .
OK or NG
OK >> GO TO 2.
NG >> Repair malfunctioning parts.
2. HISTORY OF ERRORS DIAGNOSIS
Was any error stored in AV- 1 3 9 , "
HISTORY OF ERRORS" of the CONFIRMATION/ADJUSTMENT mode?
YES or NO
YES >>AV- 1 4 0 , "DIAGNOSIS BY HISTORY OF ERRORS".
NO >>AV- 1 7 2 , "
Driving Test".
Driving TestAKS007KG
1. DRIVING TEST 1
1. Scroll the map screen to display the area to make correction. Press “ENTER” and select “CURRENT
LOCATION CORRECTION”.
2. Correct direction of the vehicle mark.
3. Perform the distance correction of the CONFIRMATION/ADJUSTMENT mode.
Note: Normally, adjustment is not necessary because this system has automatic distance correction func-
tion. However, when a tire chain is fitted, adjustment in accordance with the tire diameter ratio must be
made.
4. Are symptoms malfunctioning to the AV- 1 7 3 , "
Example of Symptoms Judged Not Malfunction" present
after driving the vehicle?
YES or NO
YES >> Limit of the location detection capacity of the navigation system.
NO >> GO TO 2.
2. DRIVING TEST 2
Did any malfunction occur when the proper test in the following test patterns is performed?

Test pattern
Driving test finds the difference between the symptoms monitored with and without each sensor.
–Test pattern 1: Test method with no GPS location correction
Disconnect GPS antenna connector (GT5) connected to the NAVI control unit. Accurately adjust the cur-
rent location and the direction, then drive the vehicle.
–Test pattern 2: Test method with no map-matching
Accurately adjust the current location and the direction. Eject the map DVD-ROM from the NAVI control
unit with ignition switch turned to OFF, then drive the vehicle. After driving, insert the map DVD-ROM back

NAVIGATION SYSTEM
AV-173
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
in the unit, display the track of the vehicle on the map screen and compare it with the actual road configu-
ration.

Sample tests
– matching or by GPS>
Perform test pattern 1.
–;
Perform test pattern 1 & 2.
Compare the track of the vehicle on the map screen and the actual road configuration. For fairly accurate
tracking, plotting shall be made every several hundred meters.
–;
Perform test pattern 1 & 2.
Drive on a road of which distance is accurately known (by utilizing distance posts on a highway). Calculate
the rate of change (increased/decreased) of the distance by comparing with the actual distance.
Correction = 1 – A/B
A: Distance shown on the screen
B: Actual distance
YES or NO
YES >>
If adjustment is insufficient, perform adjustment again.

If any error is found in the map, please let us know.

Replace NAVI control unit.
NO >> Limit of the location detection capacity of the navigation system.
Example of Symptoms Judged Not MalfunctionAKS007KH
BASIC OPERATION
VEHICLE MARK
Symptom Cause Remedy
No image is shown. Display brightness adjustment is set fully to
DARK side.Adjust the display brightness.
No guide sound is heard.
Audio guide volume is too low or
too high.Volume control is set to OFF, MIN or MAX. Adjust the audio guide volume.
Audio guidance is not available while the vehicle
is driving on a dark pink route.System is not malfunction.
Screen is too dark.
Motion of the image is too slow.Temperature inside the vehicle is low. Wait until the temperature inside the vehicle
reaches the proper temperature.
Small black or bright spots appear
on the screen.Symptom peculiar to a liquid crystal display. System is not malfunction.
Symptom Cause Remedy
Map screen and BIRDVIEW™
Name of the place vary with the
screen.Some thinning of the character data is done to
prevent the display becoming to complex. In
some cases and in some locations, the display
contents may differ.
The same place name, street name, etc. may not
be displayed every time on account of the data
processing.System is not malfunction.
Vehicle mark is not positioned cor-
rectly.Vehicle is transferred by ferry or by towing after its
ignition switch is turned to OFF.Drive the vehicle for a while in the GPS sat-
ellite signal receiving condition.
Screen will not switch to nighttime
mode after the lighting switch is
turned ON.The daytime screen is selected by the “SWITCH
SCREENS” when the last time the screen dim-
ming setting is done.
Switching between daytime/nighttime screen may
be inhibited by the automatic illumination adjust-
ment function.Perform screen dimming and select the
nighttime screen by “SWITCH SCREENS”.
Map screen will not scroll in accor-
dance with the vehicle travel.Current location is not displayed. Press “MAP” button to display the current
location.
Vehicle mark will not be shown. Current location is not displayed. Press “MAP” button to display the current
location.

NAVIGATION SYSTEM
AV-175
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
VOICE GUIDE
ROUTE SEARCH
NOTE:
Except for the ordinance-designated cities and the prefectural capitals (Malfunctioning areas may be changed in the updated map disc.) Symptom Cause Remedy
Voice guide will not operate. Note: Voice guide is only available at intersections
that satisfy certain conditions (indicated by
on
the map). Therefore, guidance may not be given
even when the route on the map changes direc-
tion.System is not malfunction.
The vehicle is not on the recommended route. Return to the recommended route or re-
search the route.
Voice guide is turned OFF. Turn voice guide ON.
Route guide is turned OFF. Turn route guide ON.
Voice guide does not match the
actual road pattern.Voice guide may vary with the direction to which
the vehicle is turn and the connection of the road
to other roads.Drive in conformity to the actual traffic rules.
Symptom Cause Remedy
No route is shown. No road to be searched is found around the des-
tination.Find wider road (orange road or wider)
nearby and reset the destination and passing
points onto it. Take care of the traveling
direction when there are separate up and
down roads.
Starting point and the destination are too close. Set the destination at more distant point.
Conditional traffic regulation (day of the week/
time of the day) is set at the area around the cur-
rent location or the destination.Turn the time-regulating search conditions
OFF. Turn “Avoid regulation time” in the
search conditions OFF.
Indicated route is intermittent. In some areas, highways (gray routes) are not
used for the search
(Note) Therefore, the route to
the current location or the passing points may be
intermittent.System is not malfunction.
When the vehicle has passed the
recommended route, it is deleted
from the screen.A recommended route is controlled by each sec-
tion. When the vehicle has passed the passing
point 1, then the map data from the starting point
up to the passing point 1 will be deleted. (The
data may remain undeleted in some area.)System is not malfunction.
Detouring route is recommended. In some areas, highways (gray routes) are not
used for the search. (Note). Therefore, detour
route may be recommended.Set the route closer to the basic route (gray
route).
A detour route may be shown when some traffic
regulation (one-way traffic, etc.) is set at the area
around the starting point or the destination.Slightly move the starting point or the desti-
nation, or set the passing point on the route
of your choice.
In the area where highways (gray routes) are
used for the search, left turn has priority around
the current location and the destination (passing
points). For this reason, the recommended route
may be detouring.System is not malfunction.
Landmarks on the map do not
match the actual ones.This can be happen due to omission or error in
the map data.As a rule, an updated map DVD-ROM will be
released once a year. Wait until the latest
map has become available.
Recommended route is far from
the starting point, passing points,
and destination.Starting point, passing points, and destination of
the route guide were set far from the desired
points because route searching data around
these area were not stored.Reset the destination onto the road nearby. If
this road is one of the highways (gray
routes), an ordinary road nearby may be dis-
played as the recommended route.

NAVIGATION SYSTEM
AV-181
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
Program Loading of NAVI Control UnitAKS007KI
SKIA0389E