2004 INFINITI FX35 Power supply

ATC-98
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
Low-pressure Side Sometimes Becomes Negative
Low-pressure Side Becomes Negative
DIAGNOSTIC PROCEDURE FOR INSUFFICIENT COOLING
SYMPTOM: Insufficient cooling
1. CHECK POWER SUPPLY FOR ECV (ELECTRONIC CONTROL VALVE)
1. Disconnect compressor (ECV) connector.
2. Turn ignition switch ON.
3. Check voltage between compressor harness connector F6 ter-
minal 2 (G) and ground.
OK or NG
OK >> GO TO 2.
NG >> Check power supply circuit and 10A fuse [No. 12,
located in the fuse block (J/B)]. Refer to PG-83, "
FUSE
BLOCK - JUNCTION BOX (J/B)" .
Gauge indication Refrigerant cycle Probable cause Corrective action
Low-pressure side sometimes
becomes negative.

Air conditioning system
does not function and does
not cyclically cool the com-
partment air.

The system constantly func-
tions for a certain period of
time after compressor is
stopped and restarted.Refrigerant does not dis-
charge cyclically.
↓
Moisture is frozen at expan-
sion valve outlet and inlet.
↓
Water is mixed with refriger-
ant.

Drain water from refrigerant
or replace refrigerant.

Replace liquid tank.
AC354A
Gauge indication Refrigerant cycle Probable cause Corrective action
Low-pressure side becomes nega-
tive.
Liquid tank or front/rear side of
expansion valve′s pipe is
frosted or dewed.High-pressure side is closed
and refrigerant does not flow.
↓
Expansion valve or liquid tank
is frosted.Leave the system at rest until
no frost is present. Start it
again to check whether or not
the malfunction is caused by
water or foreign particles.

If water is the cause, initially
cooling is okay. Then the
water freezes causing a
blockage. Drain water from
refrigerant or replace refrig-
erant.

If due to foreign particles,
remove expansion valve
and remove the particles
with dry and compressed air
(not shop air).

If either of the above meth-
ods cannot correct the mal-
function, replace expansion
valve.

Replace liquid tank.

Check lubricant for contami-
nation.
AC362A
2 – ground : Battery voltage
RJIA2294E

ATC-102
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
Self-diagnosisAJS00152
SYMPTOM: Self-diagnosis cannot be performed.
INSPECTION FLOW
*1 Compressor Clutch, ATC-143,
"REMOVAL" .*2 Compressor Clutch, ATC-145, "INSTALLATION" .*3AT C - 2 7 , "
Maintenance of Lubricant
Quantity in Compressor".
*4ATC-61, "
Operational Check".*5EM-15, "Checking Drive Belts"
(VQ35DE) or EM-169, "
Checking
Drive Belts" (VK45DE).
*1ATC-63, "
Power Supply and Ground
Circuit for Auto Amp.".*2ATC-104, "
Ambient Sensor Circuit".*3ATC-107, "In-vehicle Sensor Circuit".
*4ATC-110, "
Sunload Sensor Circuit".*5ATC-113, "Intake Sensor Circuit".*6AT C - 7 5 , "Air Mix Door Motor PBR
Circuit".
*7ATC-61, "
Operational Check".*8ATC-42, "SYMPTOM TABLE".
RJIA2014E

TROUBLE DIAGNOSIS
ATC-103
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: 2004 November 2004 FX35/FX45
Memory FunctionAJS00153
SYMPTOM: Memory function does not operate.
INSPECTION FLOW
*1AT C - 6 3 , "Power Supply and Ground
Circuit for Auto Amp.".*2ATC-61, "
Operational Check".*3AT C - 5 4 , "FUNCTION CONFIRMA-
TION PROCEDURE".
RJIA2015E

AV-1
AUDIO VISUAL, NAVIGATION & TELEPHONE SYS-
TEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION AV
A
B
AV
Revision: 2004 November 2004 FX35/FX45
AUDIO VISUAL, NAVIGATION & TELEPHONE SYSTEM
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 5
Wiring Diagrams and Trouble Diagnosis .................. 5
PREPARATION ........................................................... 6
Commercial Service Tools ........................................ 6
AUDIO ......................................................................... 7
System Description .................................................. 7
BASE SYSTEM ..................................................... 7
BOSE SYSTEM .................................................... 7
SPEED SENSITIVE VOLUME SYSTEM .............. 8
Component Parts and Harness Connector Location ..... 9
Schematic -Base System- ...................................... 10
WITH NAVIGATION SYSTEM ............................. 10
WITHOUT NAVIGATION SYSTEM ...................... 11
Wiring Diagram -AUDIO- / Base System ............... 12
Schematic -BOSE System- .................................... 19
WITH NAVIGATION SYSTEM ............................. 19
WITHOUT NAVIGATION SYSTEM ..................... 20
Wiring Diagram -AUDIO- / BOSE System .............. 21
Terminals and Reference Value for Audio Unit ....... 30
Terminals and Reference Value for BOSE Speaker
Amp. ....................................................................... 31
Terminals and Reference Value for A/C and AV
Switch ..................................................................... 33
Terminals and Reference Value for Woofer ............ 34
A/C and AV Switch Self-Diagnosis Function .......... 35
STARTING THE SELF-DIAGNOSIS MODE ....... 35
DIAGNOSIS FUNCTION ..................................... 35
EXITING THE SELF-DIAGNOSIS MODE ........... 35
Trouble Diagnosis .................................................. 35
MALFUNCTION WITH RADIO, TAPE AND CD
(BASE SYSTEM) ................................................ 35
MALFUNCTION WITH RADIO, TAPE AND CD
(BOSE SYSTEM) ................................................ 36
FOR RADIO ONLY .............................................. 37
FOR CASSETTE PLAYER ONLY ....................... 37
FOR CD ONLY .................................................... 37
Noise Inspection ..................................................... 38TYPE OF NOISE AND POSSIBLE CAUSE ........ 38
Power Supply Circuit Inspection ............................. 39
Audio Steering Wheel Switch Inspection ................ 40
A/C and AV Switch Inspection ................................ 41
BOSE Speaker Amp. Inspection ............................ 42
Vehicle Speed Signal Inspection ............................ 42
Locking CD Auto-changer Mechanism ................... 44
DAMPER LOCK PROCEDURE .......................... 44
Removal and Installation of Audio Unit ................... 44
REMOVAL ........................................................... 44
INSTALLATION ................................................... 44
Disassembly and Assembly for Audio Unit ............. 45
DISASSEMBLY ................................................... 45
ASSEMBLY ......................................................... 45
Removal and Installation for A/C and AV Switch .... 45
REMOVAL ........................................................... 45
INSTALLATION ................................................... 46
Removal and Installation for Front Door Speaker ... 46
REMOVAL ........................................................... 46
INSTALLATION ................................................... 46
Removal and Installation for Rear Door Speaker ... 46
REMOVAL ........................................................... 46
INSTALLATION ................................................... 46
Removal and Installation for Instrument Speaker ... 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 47
Removal and Installation for Tweeter ..................... 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 47
Removal and Installation for Woofer (BOSE Sys-
tem) ........................................................................ 47
REMOVAL ........................................................... 47
INSTALLATION ................................................... 47
Removal and Installation for BOSE Speaker Amp. ... 48
REMOVAL ........................................................... 48
INSTALLATION ................................................... 48
AUDIO ANTENNA .................................................... 49
System Description ................................................. 49
Wiring Diagram — M/ANT — ................................. 50
Terminals and Reference Value for Audio Unit ....... 51

AV-2Revision: 2004 November 2004 FX35/FX45Antenna Amp. Inspection ....................................... 51
Location of Antenna ................................................ 52
Window Antenna Repair ......................................... 52
CHECK ELEMENT .............................................. 52
Removal and Installation of Roof Antenna ............. 54
REMOVAL ........................................................... 54
INSTALLATION .................................................... 54
INTEGRATED DISPLAY SYSTEM ............................ 55
System Description ................................................. 55
A/C AND AV SWITCH SYSTEM .......................... 55
PRECAUTION OF LCD MONITOR ..................... 55
POWER SUPPLY AND GROUND ....................... 55
DRIVE COMPUTER ............................................ 56
E/M SWITCH ....................................................... 57
SETTING SCREEN ............................................. 58
WARNING INDICATIONS ................................... 59
AV COMMUNICATION LINE ............................... 59
CAN Communication System Description .............. 60
CAN Communication Unit ....................................... 61
Component Parts and Harness Connector Location ... 61
Schematic ............................................................... 62
Wiring Diagram — INF/D — ................................... 63
Schematic ............................................................... 68
Wiring Diagram — COMM — ................................. 69
Terminals and Reference Value for Display Unit .... 72
Terminals and Reference Value for A/C and AV
Switch ..................................................................... 73
On Board Self-Diagnosis Function ......................... 74
DESCRIPTION .................................................... 74
DIAGNOSIS ITEM ............................................... 74
Self-Diagnosis Mode .............................................. 74
OPERATION PROCEDURES ............................. 74
NETWORK CHECK ............................................. 75
PARTS CHECK ................................................... 76
HVAC DETAIL SCREEN ...................................... 76
VERSION CHECK ............................................... 76
CAN DIAG MNTR (CAN DIAG MONITOR) ......... 76
A/C and AV Switch Self-Diagnosis Function ........... 77
STARTING THE SELF-DIAGNOSIS MODE ........ 77
DIAGNOSIS FUNCTION ..................................... 77
EXITING THE SELF-DIAGNOSIS MODE ........... 77
Trouble Diagnosis Chart by Symptom .................... 78
Power Supply and Ground Circuit Check for Display
Unit ......................................................................... 79
Power Supply and Ground Circuit Check for A/C and
AV Switch ................................................................ 80
Vehicle Speed Signal Inspection ............................ 80
Illumination Signal Inspection ................................. 81
Ignition Signal Inspection ........................................ 82
Audio Communication Line Inspection ................... 82
A/C and AV Switch Does Not Operate .................... 84
CAN Communication Line Inspection ..................... 85
Audio Steering Wheel Switch Inspection ................ 85
Removal and Installation of Display ........................ 87
REMOVAL ........................................................... 87
INSTALLATION .................................................... 87
Removal and Installation of A/C and AV Switch ..... 87
NAVIGATION SYSTEM ............................................. 88
System Description ................................................. 88TRAVEL DISTANCE ............................................ 88
TRAVEL DIRECTION .......................................... 88
MAP-MATCHING ................................................. 88
GPS (GLOBAL POSITIONING SYSTEM) .......... 89
COMPONENT DESCRIPTION ............................ 90
BIRDVIEW™ ........................................................ 90
MAP DISPLAY ..................................................... 91
FUNCTION OF CENTER SWITCH ..................... 92
“VIEW” MODE ...................................................... 98
“HEADING” MODE .............................................. 99
“NEARBY DISPLAY ICONS” MODE .................... 99
“SAVE CURRENT LOCATION” MODE ................ 99
“ADJUST CURRENT LOCATION” MODE ........... 99
“AUTO RE-ROUTE” MODE ...............................100
“AVOID AREA SETTING” MODE ......................100
“CLEAR MEMORY” MODE ................................100
“EDIT ADDRESS BOOK” MODE .......................101
“GPS INFORMATION” MODE ...........................101
“QUICK STOP CUSTOMER SETTING” MODE .101
“SET AVERAGE SPEED” MODE ......................101
“TRACKING” MODE ..........................................102
GUIDANCE VOLUME ........................................102
DISPLAY WITH PUSHED “TRIP” BUTTON .......102
TRIP 1 OR TRIP 2 .............................................103
FUEL ECONOMY ..............................................103
MAINTENANCE .................................................103
ENGINE OIL OR TIRE ROTATION ....................103
TIRE PRESSURE ..............................................104
WARNING INDICATIONS ..................................104
CAN Communication System Description ............105
CAN Communication Unit .....................................105
Component Parts Location and Harness Connector
Location ................................................................105
Schematic—NAVI— ..............................................106
Wiring Diagram —NAVI— .....................................107
Schematic — COMM — ........................................115
Wiring Diagram — COMM — ................................116
Terminals and Reference Value for NAVI Control
Unit ........................................................................121
Terminals and Reference Value for Display Control
Unit ........................................................................123
Terminals and Reference Value for Display ..........127
Terminals and Reference Value for A/C and AV
Switch ...................................................................129
On Board Self-Diagnosis Function ........................130
DESCRIPTION ..................................................130
DIAGNOSIS ITEM .............................................130
Self-Diagnosis Mode (DCU) ..................................131
OPERATION PROCEDURE ..............................131
SELF–DIAGNOSIS RESULT .............................133
Self-Diagnosis Mode (NAVI) .................................133
OPERATION PROCEDURE ..............................133
SELF–DIAGNOSIS RESULT .............................135
Confirmation/Adjustment Mode .............................136
OPERATION PROCEDURE ..............................136
DISPLAY DIAGNOSIS .......................................136
VEHICLE SIGNALS ...........................................137
AUTO CLIMATE CONTROL ..............................137
NAVIGATION .....................................................138

AV-3
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45DISPLAY DIAGNOSIS ...................................... 138
VEHICLE SIGNALS .......................................... 139
HISTORY OF ERRORS .................................... 139
DIAGNOSIS BY HISTORY OF ERRORS ......... 140
NAVIGATION .................................................... 141
Can Diag Support Monitor .................................... 143
OPERATION PROCEDURE ............................. 143
A/C and AV Switch Self-Diagnosis Function ........ 144
DESCRIPTION .................................................. 144
Power Supply and Ground Circuit Check for NAVI
Control Unit .......................................................... 145
Power Supply and Ground Circuit Check for Display
Control Unit .......................................................... 146
Power Supply and Ground Circuit Check for Display . 147
Power Supply and Ground Circuit Check for A/C and
AV Switch ............................................................. 149
Vehicle Speed Signal Check for NAVI Control Unit . 149
Vehicle Speed Signal Check for Display Control Unit . 150
Illumination Signal Check for NAVI Control Unit ... 151
Illumination Signal Check for Display Control Unit . 152
Ignition Signal Check for NAVI Control Unit ......... 152
Ignition Signal Check for Display Control Unit ..... 152
Reverse Signal Check for NAVI Control Unit ....... 152
Reverse Signal Check for Display Control Unit .... 153
When Malfunctioning Connection Between Display
Control Unit and NAVI Control Unit ...................... 153
When Malfunctioning Connection Between Display
Control Unit and Audio Unit .................................. 154
When Malfunctioning Connection Between Display
Control Unit and Display ...................................... 156
CAN Communication Line Check ......................... 158
If NAVI Control Unit Detects That DVD-ROM Map
is not Inserted ....................................................... 158
If NAVI Control Unit Detects that Inserted DVD-ROM
Map Malfunctioning or if it is Impossible to Load Data
from DVD-ROM Map ............................................ 158
If Connection Between NAVI Control Unit and GPS
Antenna is Malfunctioning .................................... 159
Color of RGB Image is Not Proper (NAVI Screen
Looks Bluish) ........................................................ 159
Color of RGB Image is Not Proper (NAVI Screen
Looks Reddish) .................................................... 160
Color of RGB Image is Not Proper (NAVI Screen
Looks Yellowish) ................................................... 161
Color of RGB Image is Not Proper (All screens Looks
Bluish) .................................................................. 162
Color of RGB Image is Not Proper (All Screens
Looks Reddish) .................................................... 163
Color of RGB Image is Not Proper (All Screens
Looks Yellowish) ................................................... 164
NAVI Screen is Rolling ......................................... 166
Guide Sound is Not Heard ................................... 167
Screen is Not Shown ............................................ 167
Operating Screen for Audio and A/C is Not Dis-
played When Showing NAVI Screen .................... 168
TRIP, FUEL ECON and MAINTENANCE Screens
are Not Shown ..................................................... 169
Average Fuel Economy Displayed is Not Shown
(“***” is Shown) ..................................................... 169Driving Distance or Average Speed is Not Shown
(“***” is Shown) .....................................................170
WARNING DOOR OPEN Screen is Not Shown ...170
TIRE PRESSURE Screen is not Shown ...............170
Unable to Operate All of A/C and AV switch (Unable
to start Self-Diagnosis) .........................................171
Position of Current-Location Mark is Not Correct . 172
Driving Test ...........................................................172
Example of Symptoms Judged Not Malfunction ...173
BASIC OPERATION ..........................................173
VEHICLE MARK ................................................173
DESTINATION, PASSING POINTS, AND MENU
ITEMS CANNOT BE SELECTED/SET ..............174
VOICE GUIDE ...................................................175
ROUTE SEARCH ..............................................175
EXAMPLES OF CURRENT-LOCATION MARK
DISPLACEMENT ..............................................176
CURRENT LOCATION MARK SHOWS A POSI-
TION WHICH IS COMPLETELY WRONG ........179
CURRENT-LOCATION MARK JUMPS .............179
CURRENT LOCATION MARK IS IN A RIVER OR
SEA ...................................................................180
WHEN DRIVING ON SAME ROAD, SOME-
TIMES CURRENT-LOCATION MARK IS IN
RIGHT PLACE AND SOMETIMES IT IS WRONG
PLACE ...............................................................180
LOCATION CORRECTION BY MAP-MATCH-
ING IS SLOW ....................................................180
ALTHOUGH GPS RECEIVING DISPLAY IS
GREEN, VEHICLE MARK DOES NOT RETURN
TO CORRECT LOCATION ................................180
NAME OF CURRENT PLACE IS NOT DIS-
PLAYED .............................................................180
CONTENTS OF DISPLAY DIFFER FOR BIRD-
VIEW™ AND THE (FLAT) MAP SCREEN ........180
Program Loading of NAVI Control Unit .................181
Removal and Installation of NAVI control Unit ......182
REMOVAL .........................................................182
INSTALLATION .................................................182
Removal and Installation of GPS Antenna ...........182
REMOVAL .........................................................182
INSTALLATION .................................................182
Removal and Installation of A/C and AV Switch ...183
Removal and Installation of Display Unit ..............183
Removal and Installation of Display Control Unit . 183
REMOVAL .........................................................183
INSTALLATION .................................................183
INFINITI MOBILE ENTERTAINMENT SYSTEM .....184
System Description ...............................................184
Component Parts and Harness Connector Location .185
Wiring Diagram – MES – ......................................186
Terminals and Reference Value for DVD Player ...188
Terminals and Reference Value for DVD Display . 189
DVD Player Is Not Work .......................................191
Screen Is Not Shown (While Sounds Come Out of
an Audio Speaker, Did not do of a Head Phone) ..193
Screen is not Shown (Sounds Come Out of Both
an Audio Speaker and a Head Phone) .................194
Head Phone Does Not Sound ..............................195

PRECAUTIONS
AV-5
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2004 November 2004 FX35/FX45
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS007X5
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Wiring Diagrams and Trouble DiagnosisAKS007X6
When reading wiring diagrams, refer to the following:

Refer to GI-15, "How to Read Wiring Diagrams" .
Refer to PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
When performing trouble diagnosis, refer to the following:

Refer to GI-11, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" .
Refer to GI-27, "
How to Perform Efficient Diagnosis for an Electrical Incident" .

AV-30
AUDIO
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for Audio UnitAKS00BMN
Terminal
(Wire color)
ItemSignal
input/
outputCondition
Reference valueExample of symp-
tom
+–Ignition
switchOperation
2 (W)
*1 ,
(L)*21 (B)*1 ,
(B/W)*2
Audio sound
signal front
LHOutput ON
Receive audio
signalNo sound from
front door speaker
LH and instru-
ment speaker LH.
4 (G)*
1 ,
(G/B)*23 (R)*1 ,
(B/R)*2
Audio sound
signal front
RHOutput ONNo sound from
front door speaker
RH and instrument
speaker RH.
5 (R/W) GroundAntenna
signalOutput ON – Approx. 12VAntenna amp.
does not work
properly.
6 (W/L) GroundBattery
power sup-
plyInput OFF – Battery voltageSystem will not
work properly.
9*
1– Shield – ON – Approx.0V –
10
(LG/R)GroundACC power
supplyInput ACC – Battery voltageSystem does not
work properly.
11 *
1– Shield – ON – Approx.0V –
12*
3
(G/W)GroundAmp ON sig-
nalOutput ON – Approx. 12VBOSE speaker
amp. does not
work properly.
14
(BR)*
1 ,
(L/W)*2
13 (Y)*1 ,
(B/Y)*2
Audio sound
signal rear
LHOutput ON
Receive audio
signalNo sound from
rear door speaker
LH.
16 (L)*
1 ,
(R/G)*215 (P)*1 ,
(L/B)*2
Audio sound
signal rear
RHOutput ONNo sound from
rear door speaker
RH.
21
(B/Y)GroundAudio TX
signal (AUD
- DCU) Output ONOperate audio
volumeAudio does not
operate properly.
22
(W/L)GroundVehicle
speed signal
(2 pulse)Input ONWhen vehicle
speed is
approx. 40
km/h (25MPH)Speed sensitive
volume system
dose not work
properly.
23 (LG) GroundAudio RX
signal (DCU
- AUD)Input ONOperate audio
volumeAudio does not
operate properly.
25 – Shield – ON – Approx.0V –
SKIA0177E
SKIA0177E
SKIA4402E
ELF1080D
SKIA4403E