2004 Hyundai Terracan display

FEATURES OF YOUR HYUNDAI 1- 45
B990A01HP-GAT MULTIMETER(If installed)
1. Digital Clock
2. Azimuth Compass
3. Altimeter/Relative altimeter/Barometer
4. Azimuth adjustment switch5. Up switch
6. Down switch
7. Road display responsive to vehicle speed
8. Mode conversion switch
9. Light switch
1
23
456 7 8 9 B990B01HP-GAT HOW TO ADJUST MULTIMETER Switch function
Switch
Mode
(Up),
(Down) LightAdjust Function
Selecting of time adjustment mode (more than 2 sec)Altimeter correctionSetting altitude to "0"Time adjustmentIllumination on/off Selecting correction mode of azimuth indicator
B990C01HP-GAT Electrical azimuth compass
B990C01HP
B990A01HP
Azimuth Comass
Altimeter Relative Altimeter
Barometer

FEATURES OF YOUR HYUNDAI
1- 46
It displays 16 azimuths according to the vehicle driving direction and the angle of one graduationis 22.5°.
NOTE: If new vehicle is first driven or if the batteryhas been disconnected, correct the azimuthindicator before driving. Correcting azimuth indicator This is need to correct the error between a current azimuth of terrestrial magnetism sensorand the displayed azimuth in the vehicle position. How to correct azimuth indicator
1. If you push the "ADJ" switch and hold for less
than 3 sec, the azimuth indicator will start to blink.
2. Slowly rotate the vehicle one turn within 128 sec. B990D01HP-GAT ALTIMETER
B990C02HP 3. After the rotation is finished, the azimuth
compass indicator will stop blinking and now correcting error is made.
NOTE:It is normal if the azimuth is displayed abnor-mally in specific places(tunnel, parking lot inbuilding, basement garage, area in the vicin-ity of a transformer station, etc.). The azimuthis displayed normally after escaping thoseplaces. Altimeter is operated by atmospheric pressure. The air pressure variation is converted to thealtitude on the basis of the sea level(0m, it isequal to 1013.25hpa) by the 50m.The measurement range is 0~2,800m. And whenthe altitude is under 50m, it is displayed to 0m. B990D01HP
Altitude Correction Displayed altitude could vary even at same place because of air pressure variation at sea level(0mpoint). So you can correct this display error in±300m range by pushing " (up)", " (down)"as listed in following table.
Switch (UP) (DOWN)
Pushing time Less than 0.5 sec More than 0.5 secLess than 0.5 secMore than 0.5 sec Altitude
Increasing by 50m Increasing by 50m gradually Decreasing by 50mDecreasing by 50m gradually
B990E01HP-GAT RELATIVE ALTIMETER Relative altimeter is used when you want to know the altitude of the specific location. And it dis-plays by comparing the altitude of the specificlocation with the current altitude which the ve-hicle is located in.When the "MODE" switch is pressed for lessthan 2 sec, the relative altimeter mode is se-lected. B990E01HP

FEATURES OF YOUR HYUNDAI 1- 47
When you want to know the difference of altitude between the destination and the starting point.
1. Press the " (UP)" and " (DOWN)" switchsimultaneously for more than 1 sec to reset the current altitude to 0m.
2. After arriving, the displayed altitude is the difference of altitude between the destinationand the starting point.
Destination
B990E02HP
B990F01HP-GAT BAROMETER The current air pressure is displayed in hpa units
where the measurement range is from 720hpa to1,045hpa.(The minimum is 1hpa)If the "MODE" switch is pressed for less than 2sec from "Relative Altimeter" mode, the atmo-spheric pressure will be displayed on the displaywindow.
B990F01HP
B990G01HP-GAT DIGITAL CLOCK If you press "MODE" switch for more than 2 sec, the mode that you can adjust the time is dis-played. How to adjust the time
1. In time adjustment mode, push the "MODE" switch briefly, and you can adjust "minute". And if you push "MODE" switch once more
briefly, you can adjust "hour".
2. Adjust the time by pushing " (UP)"," (DOWN)" switch when the time blinks.
3. After adjusting the time, push "MODE" switch for more 2sec, and the mode for adjusting thetime is cancelled. B990G01HP
B990H01HP-GAT ROAD DISPLAY RESPONSIVE TO VE- HICLE SPEED
B990H01HP
The road display indicator blinks according to the vehicle speed.Vehicle speed
Below 2.8 km/h
2.8 ~ 40 km/h
41 ~ 60 km/h 61 ~ 80 km/h
81 ~ 100 km/h
Above 100 km/h Blinking cycle
Total Lightening
1 sec
0.8 sec0.5 sec 0.3 sec0.2 sec
The difference of altitude between the destinationand the starting point : 1000 m
Starting point

FEATURES OF YOUR HYUNDAI
1- 52
B420A02A-AAT CIGARETTE LIGHTER
For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position.To use the cigarette lighter, push it all the way intoits socket. When the element has heated, thelighter will pop out to the "ready" position.Do not hold the cigarette lighter pressed in. Thiscan damage the heating element and create afire hazard.If it is necessary to replace the cigarette lighter,use only a genuine Hyundai replacement or itsapproved equivalent. CAUTION: Do not use electric accessories or equipmentother than the Hyundai genuine parts in thesocket.
B410A01A-AAT INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT) (If installed)
B410A01HP
The instrument panel lights can be made brighter or dimmer by turning the instrument panel lightcontrol knob.
B420A01HPB500D01HP
4. MODE - Push "MODE" button to display a 12-
or 24-hour clock.
When the 12-hour clock is in use, the letters AM or PM appear with the time.
5. - The time is displayed on the LCD by pushing in on the switch and is turned off by pushing in on the switch again.
If your vehicle is equipped with the multimeter,see the page 1-46. B500D07O-AAT POWER OUTLET (If installed) These supply 12V electric power to operate electric accessories or equipment only when thekey is in the "ON" or "ACC" position. CAUTION: Do not use the power outlet to connect elec-tric accessories or equipment other thanthose designed to operate on 12 volts.

FEATURES OF YOUR HYUNDAI
1- 74
B970A01Y-AAT AUTOMATIC HEATING AND COOLING CONTROL SYSTEM (If lnstalled) Your Hyundai is equipped with an automatic heating and cooling control system controlled bysimply setting the desired temperature. B970B01HP-GAT Heating and Cooling Controls
1. Blower Fan Control Switch
2. AUTO (Automatic Control)Switch
3. OFF Switch
4. Display Window
5. Temperature Control Button
6. Defroster Switch
7. Rear Window Defroster Switch (If installed) 8. Air Flow Control Switch
9. Air Conditioning Switch
10. Ambient Temperature Switch
11. Air Intake Control Switch
(Recirculation air)
12. Air Intake Control Switch (Fresh air) B970B01HP
1
2
3 45
67 891
0
1112

FEATURES OF YOUR HYUNDAI 1- 75
B970C02L-AAT Automatic Operation
B970C01HP
The FATC (Full Automatic Temperature Control) system automatically controls heating and cool-ing as follows:
1. Push the "AUTO" switch. The indicator light will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blowerspeed and, air conditioner will be controlledautomatically. 2. Push the "TEMP" button to set the desired
temperature.The temperature will increase to the maxi-mum 32°C(90°F) by pushing on the button. Each push of the button will cause the tem- perature to increase by 0.5°C(1°F).The temperature will decrease to the mini-mum 17°C(62°F) by pushing on the button.Each push of the button will cause the tem-perature to decrease by 0.5°C(1°F).
NOTE:If the battery has been discharged or discon-nected, the temperature mode will reset toCentigrade degrees.This is a normal condition and you can changethe temperature mode from Centigrade toFahrenheit as follows;Press the TEMP down ( ) button 3 secondsor more with the AMB button held down.
Photo sensor
B970C02HP
NOTE: Never place anything over the sensor whichis located on the instrument panel to ensurebetter control of the heating and coolingsystem.
The display shows that the unit of tempera- ture is adjusted to Centigrade or Fahrenheit(°C °F or °F °C).
HHP062A

FEATURES OF YOUR HYUNDAI
1- 76
B980A01Y-AAT MANUAL OPERATIONThe heating and cooling system can be con- trolled manually as well by pushing buttons otherthan the "AUTO" button. In this state, the systemsequentially works according to the order ofbuttons selected.The function of the buttons which are not select-ed will be controlled automatically.Press the "AUTO" button in order to convert toautomatic control of the system.
B995A01HP
Pressing the AMB button displays the ambient temperature on the display.
B980B01Y-AAT Fan Speed Control Switch
B980B01HP
The fan speed can be set to the desired speed by pressing the appropriate fan speed control but-ton. The higher the fan speed is, the more air isdelivered. Pressing the "OFF" button turns offthe fan.
B995A01Y-AAT AMBIENT TEMPERATURE SWITCHB980C01HP
B670C02HP-GAT Air Intake Control Switch This is used to select fresh outside air or recircu- lation inside air.To change the air intake control mode, push thecontrol button. FRESH MODE ( ) : The indicator light on the button is illuminated when the air intakecontrol is in fresh mode.
RECIRCULATION MODE ( ) :
The indica-
tor light on the button is illuminated when the air
intake control is in recirculation mode. With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooledaccording to the function selected. With the "Recirculation" mode selected, air from within the passenger compartment will be drawnthrough the heating system and heated or cooledaccording to the function selected.

FEATURES OF YOUR HYUNDAI 1- 83
FM/AM
FAD (Fader Control) Knob Pull the treble control knob further out. Turn the control knob counterclockwise to em-phasize front speaker sound (rear speaker soundwill be attenuated).When the control knob is turned clockwise, rearspeaker sound will be emphasized (front speakersound will be attenuated). 4. TUNE (Manual) Select Button Press the side or side to increase or to decrease the frequency. Press either button andhold down to continuously scroll. Release buttononce the desired station is reached. SEEK Operation (Automatic Channel Selection) Press the TUNE select button 0.5 sec or more. Releasing it will automatically tune to the nextavailable station with a beep sound.When the side is pressed longer than 0.5second, releasing will automatically tune to thenext higher frequency and when the side ispressed longer than 0.5 second, releasing willautomatically tune to the next lower frequency. 5. BAND Selector Pressing the button changes the AM, FM1 and FM2 bands. The mode selected is displayedon LCD.6. PRESET STATION SELECT Button Six (6) stations for AM, FM1 and FM2 respective- ly can be preset in the electronic memory circuiton this unit. HOW TO PRESET STATIONS Six AM and twelve FM stations may be pro- grammed into the memory of the radio. Then, bysimply pressing the band select button and/orone of the six station select buttons, you mayrecall any of these stations instantly. To programthe stations, follow these steps:
o Press band selector to set the band for AM,
FM1, or FM2.
o Select the desired station to be stored by seek or manual tuning.
o Determine the preset station select button you wish to use to access that station.
o Press the station select button for more than two seconds. A select button indicator will show in the display indicating which selectbutton you have depressed. The frequencydisplay will flash after it has been stored intothe memory with a beep sound. You shouldthen release the button, and proceed to pro-gram the next desired station. A total of 18stations can be programmed by selecting oneAM and two FM stations per button.
o When completed, any preset station may be recalled by selecting AM, FM1 or FM2 bandand the appropriate station button.
H240B03O-AAT
1. POWER ON-OFF Control KnobThe radio unit may be operated when the ignition key is in the "ACC" or "ON" position. Press theknob to switch the power on. The LCD shows theradio frequency in the radio mode or the tapedirection indicator in the tape mode. To switchthe power off, press the knob again. VOLUME Control Rotate the knob clockwise to increase the vol- ume and turn the knob counterclockwise to re-duce the volume. 2. BASS Control Knob Press to pop the knob out and turn to the left or right for the desired bass tone. BAL (Balance Control) Knob Pull the bass control knob further out. Turn the control knob clockwise to emphasize rightspeaker sound (left speaker sound will be at-tenuated).When the control knob is turned counterclock-wise, left speaker sound will be emphasized(right speaker sound will be attenuated). 3. TREB (Treble Control) Knob Press to pop the knob out and turn to the left or right for the desired treble tone.