2004 HONDA INSIGHT reset

This indicator comes on with the
high beam headlights. See pagef or inf ormation on the headlight
controls.
On Canadian models, this indicator
comes on with reduced brightness
when the Daytime Running Lights
(DRL) are on (see page ).
This indicator comes on when you
turn the ignition switch to ON (II)
with the headlight switch off and the
parking brake set. It should go of f if
youturnontheheadlightsorrelease
the parking brake. If it comes on at
any other time, it means there is a
problem with the DRL. There may
also be a problem with the high
beam headlights. This indicator comes on f or a f ew
seconds when you turn the ignition
switch to ON (II). It will go of f if you
have inserted a properly-coded
ignition key. If it is not a properly-
coded key, the indicator will blink
and the engine will not start (see
page ).
This indicator also blinks several
times when you turn the ignition
switch f rom ON (II) to ACCESSORY
(I) or LOCK (0).
This indicator comes on if either
door or the hatch is not closed
tightly.
This indicator comes on as a
reminder that you must ref uel soon.This indicator normally comes on
when you turn the ignition to ON (II)
and goes off after the engine starts.
If it comes on at any other time,
there is a problem in the Electric
Power Steering system. If this
happens, stop the vehicle in a saf e
place, and turn of f the engine. Reset
the system by restarting the engine,
and watch the EPS indicator. If it
does not go of f , or comes back on
again while driving, take the vehicle
to your dealer to have it checked.
With the indicator on, the EPS is
turned off, making the vehicle
harder to steer.
54
5458
Canadian models only
Instrument Panel Indicators
High Beam Indicator
‘‘Daytime Running
Lights’’ Indicator Immobilizer System
Indicator
Door and Hatch Open
Indicator
Low Fuel IndicatorElectric Power Steering
(EPS) Indicator
Inst rument s and Cont rols44

This indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance.
Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages and .
When the distance driven since the
last scheduled maintenance reaches
6,000 miles (9,600 km), the indicator
starts blinking. If you exceed 7,500
miles (12,000 km), the indicator
stays on.
Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Honda dealer, reset the indicator as
f ollows.Turn of f the engine. Press and hold the TRIP button in
the instrument panel, then turn
the ignition switch to ON (II).
Hold the button for about 10
seconds until the indicator resets.
1. 2.
3.
127 128
Instrument Panel Indicators
Inst rument s and Cont rols
Maintenance Required
Indicator
45
TRIP BUTTON

This shows how much f uel you have.
It may show slightly more or less
than the actual amount.This shows the temperature of the
engine’s coolant. During normal
operation, the reading should be in
the middle of the gauge. In severe
driving conditions, the reading may
reach near the red mark. If it
reaches the red mark, pull saf ely to
thesideof theroad.Turntopage
f or instructions and precautions
on checking the engine’s cooling
system. The odometer shows the total
distance your vehicle has been
driven in miles and kilometers. It is
illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles and kilometers
indicated.
Push the Display Change button to
switch the speedometer, trip meter,
and odometer reading between miles
per hour and kilometers per hour.
175
Gauges
Inst rument s and Cont rols
Fuel Gauge
T emperature GaugeOdometer
Display Change Button
47
NOTICE:Avoid driving with an
extremely low f uel level. Running out
of f uel could cause the engine to
misf ire, damaging the catalytic
converter.

This display shows the current, or
instantaneous fuel mileage you are
getting. (U.S.: miles per hour and
mpg, Canada: kilometer per hour
and l/100 km)
You can turn off this display at any
time. See page .The trip meters show the number of
miles or kilometers driven since you
last reset them.
There are two trip meters: Trip A
and Trip B. Each trip meter works
independently, so you can keep track
of two dif f erent distances. To change
the display to show Trip A, Trip B, or
the odometer, press the Trip button
repeatedly.
To reset a trip meter, display it, then
press and hold the Trip button until
the numbers reset to 0.0.
When you reset a trip meter, the
average fuel mileage for that trip
meter also resets. When a trip meter is displayed, the
average fuel mileage you have been
getting during that trip is shown in
the Fuel Mileage display. This
number is updated once per minute.
This display can be turned of f at any
time. See page .
50
50
Gauges
Inst rument s and Cont rols
Current Fuel MileageT rip Meters T rip Mileage
48
CURRENT FUEL MILEAGE
TRIP MILEAGE (TRIP A)TRIP BUTTON

Press the FCD select button to
display the distance and average fuel
mileage f or a segment of a trip. The
Segment Display indicator will come
on to remind you that this is the
segment distance and f uel mileage
display.To reset the display, press and hold
the FCD Select button until the
display resets to zero and dashes.
The system then begins displaying
the distance and average f uel
mileage f rom that point. The display
is updated once per minute.
To switch between the segment
display and the Trip Meter/
Odometer display, press and release
the FCD Select button.When the odometer is displayed, the
Fuel Mileage display shows the
lif etime f uel mileage. This is the
average f uel mileage your vehicle
has gotten since the last time the
display was reset.
CONT INUED
Gauges
Inst rument s and Cont rols
Segment Distance and Fuel
Mileage
Lifetime Fuel Mileage
49
LIFETIME FUEL MILEAGE
FUEL CONSUMPTION DISPLAY (FCD)
SELECT BUTTON SEGMENT
DISPLAY
INDICATOR

To reset this display, turn the
ignition switch to ON (II), the
transmission is in neutral or Park
(CVT),andtheparkingbrakeisset.
Use the Trip button to display the
odometer. Then press and hold the
Trip button until the Lif etime Fuel
Mileage Display begins to blink
(approximately f ive seconds).
Release the Trip button, then press it
again while the display is blinking
andholdituntilthedisplayclearsto
dashes.You can temporarily turn of f the
Current Fuel Mileage and Fuel
Mileage displays.
To turn them off:
Turn the ignition switch to ON (II),
the transmission is in neutral or
Park (CVT), and the parking
brake is set.
Use the Trip button to select Trip
A, Trip B, or the odometer.
Press and hold the FCD Select
button f or approximately three
seconds. The Current Fuel
Mileage display will turn of f .
Press and hold the FCD Select
button again. The Fuel Mileage
display f or the meter you are
displaying (Trip A, Trip B, or
odometer) will turn of f . Use the Trip button to select
another mileage display.
To turn of f the other trip meters,
select the meter with the Trip
button, and hold the FCD select
button.
Although the displays are turned off,
the average fuel mileages continue
to be calculated. The displays will
turn back on when you press and
hold the FCD Select button again.
1.
3.
4. 2. 5.
6.
Gauges
Inst rument s and Cont rols
T urning Of f the Mileage Displays
50

Playing the Radio
Comf ort and Convenience Feat ures78
SEEK BAR
PWR/VOL KNOB TUNE KNOB
STEREO INDICATOR
SCAN BUTTON
PRESET BUTTONS
AM/FM BUTTON
SCAN INDICATOR
AUTO SELECT INDICATOR AUTO SELECT BUTTON

µµ
µ
µ
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
PWR/VOL knob or the AM/FM
button. Adjust the volume by turning
thesameknob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction on
AM is not available.
You can use any of f ive methods to
f ind radio stations on the selected
band:
the
preset buttons, and .
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a lower f requency.
The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
bar, then release it. Each preset button can
store one f requency on AM, and two
f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
Pick a preset button, and hold it
until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
stations on FM.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan f or
a station with a strong signal. When
it f inds one, it will stop and play that
station for about 5 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 5 seconds. When it plays a
station you want to listen to, press
the SCAN button again. 1.
2.
3.
4.
CONT INUED
Playing the Radio
Comf ort and Convenience Feat ures
To Play the Radio
To Select a Station
TUNE,SEEK,SCAN, AUTO SELECT
TUNE SEEK
Preset
SCAN
79