2004 HONDA ACCORD clock

On models without Navigation SystemOn models with Navigation System
If your vehicle’s battery is
disconnected or goes dead, you will
need to set the clock.You can quickly set the time to the
nearest hour. Pressing and holding
the SOUND button, then pressing
theR(Preset6)sideof thebarsets
the clock back to the previous hour.
If the displayed time is after the half
hour, the clock sets the clock
f orward to the beginning of the next
hour.For example:
1:06 would RESET to 1:00.
1:52 would RESET to 2:00.
Ref er to the Navigation System
Owner’s Manual to set up the time.
Press and hold the SOUND button.
Change the hours by pressing the
until you hear a beep. The displayed
time begins to blink H (Preset 4)
side of the bar until the numbers
advance to the desired time. Change
the minutes by pressing the M
(Preset 5) side of the bar until the
numbers advance to the desired time.
When you are f inished, press the
SOUND button again to set the time.
Setting the Clock
Features153
DIGITAL CLOCK
SOUND BUTTON PRESET BARS
EX, EX-V6 and LX-V6 Models
without Navigation System shown
——y


y
(
y
y

When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill. Clean
up any spill immediately; it could
damage components in the engine
compartment.
Put the radiator cap back on and
tighten it.Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.
4. 5.
1. 2. 3.
Engine Coolant
Maint enance220
6-cylinder models RADIATOR CAP
RADIATOR CAP
4-cylinder models
——y

y
(
yy

CONT INUED
Open the hood. To change a bulb
on the passenger’s side, undo the
two fasteners and remove the air
intake cover.Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Install the new bulb and turn it
one-quarter turn clockwise to lock
it in place.
1.
3.
2.
4.
Lights
Maint enance
High Beam Headlight
229
FASTENERS
4-cylinder models 6-cylinder models TAB
BULB
AIR INTAKE
COVER AIR INTAKE
COVER
FASTENERS
4-cylinder models
——y
y
(
yy

Push the electrical connector onto
the bulb.To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
Remove the electrical connector
fromthebulbbysqueezingthe
connector to unlock the tab, then
slide the connector of f the bulb.
Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Turn on the headlights to test the
new bulb.
(Passenger’s side)
Reinstall the air intake cover.
Reinstall the two fasteners and
secure them by pushing on the
heads until they lock.
6.
5.
3. 4. 5.
1. 2.
7.
Lights
Maint enance
L ow Beam Headlight
230
HOLDING CLIPS
TAB BULB
6-cylinder models BULB
——y
y
(
yy

Install the new bulb and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector onto
the bulb.
Put the inner f ender cover in place.
Install the two holding clips. Lock
each one in place by pushing on
the center.
Turn on the headlights to test the
new bulb.
Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.
Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
1.
3.
2. 4.
8.
7.
6. 9.
CONT INUED
Lights
Maint enance
Replacing the Front Side Marker/
Turn Signal and Parking L ightBulb
231
HOLDING CLIPS
BULB
——y

y
(
yy

To remove the burned out bulb,
push it in and turn it
counterclockwise until it unlocks.
Install the new bulb and turn it
clockwise to lock it in place.
Insert the socket into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.
5. 6. 7. 8. 9.
Lights
Maint enance232
——y
y
(
yy

Open the trunk.
Remove the light assembly cover
by pulling its outside edge.
Remove the socket by turning it
one-quarter turn counterclockwise
and pull the bulb straight out of its
socket.Push a new bulb straight into the
socket until it bottoms, and
reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Open the trunk.
Remove the trim clips f rom the
right or lef t corner of the trunk lid
trim by caref ully prying them
using a small, f lat-tip screwdriver
wrapped with tape.
Testthelightstomakesurethe
new bulb is working.
Reinstall the light assembly cover.
1. 3.
2. 4. 5.
1. 2.
6.
6-cylinder models
CONT INUED
Lights
Maint enance
Replacing Rear Bulbs
(in Fenders)
Replacing Rear Bulbs
(in T runk L id)
233
BULBS
COVER SOCKETS
TRIM CLIPS
——y
y
(
yy

Caref ully bend back the corner of
the trunk lid trim to expose thebulbs.
Remove the socket by turning it
one-quarter turn counterclockwise
and pull the bulb straight out of its
socket.Install a new bulb into the socket
and reinstall the socket into the
light assembly.
Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket.
Press the trim clips back into their
holes.
Push the trunk lid trim back into
position.
Test the lights.
3. 4. 5.6. 7.1. 2. 3.
8.
Lights
Maint enance
Replacing a High-mount Brake
Light Bulb
234
BULBS
SOCKETS BULBS SOCKETS
BULBSOCKET
——y
y
(
yy