2004 DODGE INTREPID turn signal bulb

•To avoid drawing exhaust gases into the vehicle, close
the trunk while driving. However, if for some reason it
must remain open, close all windows. Adjust the
heating or cooling system to force outside air into the
vehicle. Set the blower at high speed.
Safety Checks You Should Make Inside the
Vehicle
Seat Belts
Inspect the belt system periodically, checking for cuts,
frays and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.
Safety belt assemblies must be replaced after an accident
if they have been damaged (bent retractor, torn webbing,
etc.). If there is any question regarding belt or retractor
condition, replace the belt.
Airbag Light
The light should come on and remain on for 6 to
8 seconds as a bulb check when the ignition
switch is first turned ON. If the bulb is not lit
during starting, have it replaced. If the light stays on or
comes on while driving, have the system checked by an
authorized dealer.
Defrosters
Check operation by selecting the defrost mode and place
the blower control on high speed. You should be able to
feel the air directed against the windshield.
Periodic Safety Checks You Should Make Outside
the Vehicle
Tires
Examine tires for excessive tread wear or uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread. Inspect for tread cuts or sidewall
cracks. Check wheel nuts for tightness and tires (includ-
ing spare) for proper pressure.
Lights
Have someone observe the operation of exterior lights
while you work the controls. Check turn signal and high
beam indicator lights on the instrument panel.
Fluid Leaks
Check area under vehicle after overnight parking for
brake fluid, fuel, water, oil, or other fluid leaks. Also, if
gasoline fumes are present, the cause should be corrected
immediately.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Turn Signals
The arrows on each side of the instrument cluster flash to
show operation of the front and rear turn signal lights. If
either light flashes at an extremely fast rate, check for a
defective outside light bulb. If both of the indicators fail
to light when the lever is moved, it would suggest that
the fuse or indicator bulbs are defective.
Headlight Dimmer Switch
Pull the multi-function control lever toward the steering
wheel to switch the headlights from high or low beam.
Passing Light
You can signal another vehicle with your headlights by
lightly pulling the multi-function lever toward the steer-
ing wheel. This will cause the headlights to turn on at
high beam and remain on until the lever is released.
Windshield Wipers And Washers
The wipers and washers are operated by a switch in the
control lever. Turn the end of the handle to select the
desired wiper speed.To use the washer, push the knob in when spray is
desired. If the button is pushed while in the delay range,
the wiper will operate for several seconds after the knob
is released, and then resume the intermittent interval.
If the button is pushed and held while in the OFF
position, the wiper will operate for several wipes then
turn off.
If the button is pushed while in the OFF position, the
wipers will cycle twice.
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫Fuel System Hoses....................194
▫Automatic Transaxle...................194
▫Appearance Care And Protection From
Corrosion...........................197
Fuses...............................201
▫Fuse Block Relays.....................201
▫Underhood Fuses.....................202
Replacement Bulbs.....................204
Exterior Light Bulb Service...............204
▫Headlight Replacement.................204
▫Front Park, Turn Signal And Side
Marker Light........................205▫Fog Light...........................206
▫Center Stop Light.....................206
▫Tail, Stop, Back Up, And Turn Signal Lights . . 207
▫License Plate Light....................207
Specifications.........................208
Fluid Capacities.......................208
Recommended Fluids, Lubricants And Genuine
Parts
...............................209
▫Engine.............................209
▫Chassis............................209
▫Body..............................210
166 MAINTAINING YOUR VEHICLE

REPLACEMENT BULBS
Interior Light Bulbs Bulb No.
Cluster Illumination.....................PC194
Turn Signal...........................PC194
Climate Control.......................... 330
Overhead Console, Front Reading, Courtesy, Grab
Handle................................ 192
Trunk................................. 906
Exterior Light Bulbs Bulb No.
Low Beam Headlights....................9006
High Beam Headlights....................9005
Park, Turn, & Side Marker................3157A
Fog Light.............................. H-3
Center Stop Light........................ 922
Tail, Stop, & Turn........................3157
Rear Side Marker........................ 168
Back-Up..............................3157
License................................ 168
EXTERIOR LIGHT BULB SERVICE
Headlight Replacement
1. Open the hood and remove the headlight assembly
mounting screws.
2. Pull the headlight assembly forward to access the
bulbs.
3. Turn the bulb assembly retaining ring counterclock-
wise and pull the bulb and socket assembly from the
housing.
204 MAINTAINING YOUR VEHICLE

4. Remove the bulb from the socket and replace the bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life.
If the bulb comes into contact with any oily surface,
clean the bulbs with rubbing alcohol.
5. Reinsert the bulb and socket assembly and turn the
retaining ring clockwise to secure the bulb.
6. Reinstall the headlight assembly.
Front Park, Turn Signal and Side Marker Light
1. Open the hood and remove the headlight assembly
mounting screws.2. Pull the headlight assembly forward to access the
bulbs.
3. Turn the bulb and socket assembly counterclockwise
and remove it from the housing.
4. Pull the bulb from the socket, install the new bulb,
reinstall the bulb and socket assembly. Reinstall the
headlight assembly.
MAINTAINING YOUR VEHICLE 205
7

Tail, Stop, Back Up, and Turn Signal Lights
1. Open the trunk and remove the fasteners securing the
light housing to the body.
2. Pull the light housing from the body to expose the
wiring socket.
3. Turn the bulb socket counterclockwise to remove from
the housing. Pull the bulb from the socket.
4. Replace the bulb, reinstall the socket, and reattach the
light housing.
License Plate Light
1. Remove the screws securing the light to the rear fascia.
2. Remove the bulb and socket assembly and pull the
bulb from the socket.
3. Replace the bulb and reinstall the bulb and socket
assembly.
MAINTAINING YOUR VEHICLE 207
7