2004 DAEWOO NUBIRA airbag off

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 23
DAEWOO V–121 BL4
DTC 6
Passenger Airbag Deployment Loop Resistance Is Low
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of driv-
er belt pretensioner. Is the wiring damaged?–Replace the
wiring.Go to Step 3
31. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of driver belt preten-
sioner.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal 1
and 2 of driver belt pretensioner. Is the resist-
ance ?ΩGo to Step 4Go to Step 5
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
passenger airbag module.–––
5Replace the airbag wiring.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 25
DAEWOO V–121 BL4
DTC 7
Passenger Airbag Deployment Loop Is Shorted To
Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of pas-
senger airbag. Is the airbag wiring damaged?–Replace the
airbag wiring.Go to Step 3
31. Confirm the ignition switch ”OFF”.
2. Remove the passenger airbag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the SDM and
the high, low wiring of passenger airbag mod-
ule and the ground. Is the resistance 10KΩ?10 KΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
passenger airbag.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 27
DAEWOO V–121 BL4
DTC 8
Passenger Airbag Deployment Loop Is Shorted To Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of pas-
senger airbag. Is the airbag wiring damaged?–Replace the
airbag wiring.Go to Step 3
31. Confirm the ignition switch ”OFF”.
2. Remove the passenger airbag module.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the SDM and
the high, low wiring of passenger airbag mod-
ule and the battery. Is the resistance 10KΩ?10 KΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
passenger airbag module.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 29
DAEWOO V–121 BL4
DTC 9
Driver Belt Pretensioner Deployment Loop Resistance Is
High
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury
Step
ActionValue(s)YesNo
1Visually inspect the connector and the wiring of pas-
senger belt pretensioner. Is the connector discon-
nected?–Connect the
connector.Go to Step 2
21. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the passenger belt
pretensioner.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal 1,2
of SDM and the terminal 1,2 of passenger belt
pretensioner. Is the resistance 10KΩ?10K ΩGo to Step 3Replace the
airbag wiring.
31. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
driver belt pretensioner.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 31
DAEWOO V–121 BL4
DTC 10
Driver Belt Pretensioner Deployment Loop Resistance Is
Low
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of driv-
er belt pretensioner. Is the wiring damaged?–Replace the
wiring.Go to Step 3
31. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of driver belt preten-
sioner.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal 1
and 2 of driver belt pretensioner. Is the resist-
ance ? ΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
If the DTC is not removable, then replace the driver
belt pretensioner.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 33
DAEWOO V–121 BL4
DTC 11
Driver Belt Pretensioner Deployment Loop Is Shorted To
Ground
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of air-
bag. Is the airbag wiring damaged?–Go to Step 3Go to Step 4
31. Replace the airbag wiring–––
4Check the resistance between the SDM and the
high, low wiring of driver belt pretensioner and the
ground. Is the resistance 10KΩ?
10K ΩGo to Step 5Replace the
airbag wiring.
51. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
driver belt pretensioner.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 35
DAEWOO V–121 BL4
DTC 12
Driver Belt Pretensioner Deployment Loop Is Shorted To
Power
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
11. Confirm the ignition switch ”OFF”.
2. Wait for a minute to discharge the SDM char-
ger.–Go to Step 2–
2Visually inspect the connector and the wiring of air-
bag. Is the airbag wiring damaged?–Replace the
airbag wiring.Go to Step 3
3Check the resistance between the SDM and the
high, low wiring of driver belt pretensioner and the
battery. Is the resistance 10KΩ?
10K ΩGo to Step 4Replace the
airbag wiring.
41. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
5. If the DTC is not removable, then replace the
driver belt pretensioner.–––

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B – 37
DAEWOO V–121 BL4
DTC 13
Passenger Belt Pretensioner Deployment Loop
Resistance Is High
CAUTION : The sensing and diagnostic module(SDM)
can maintain sufficient voltage to deploy the airbags
and pretensioners for 1 minute after the ignition is
OFF and the fuse has been removed. If the airbags
and pretensioners are not disconnected, do not be-
gin service until one minute has passed after discon-
necting power to SDM. Otherwise, injury could result.
CAUTION : During service procedure, be very careful
when handling the SDM. Never strike or jar the SDM.Never power the supplemental inflatable re-
straints(SIR) when the SDM is not rigidly attached to
the vehicle. All SDM mounting bolts must be carefully
tightened , and the arrow on the SDM must be point
toward the front of the vehicle to ensure proper op-
eration of the SIR. The SDM could be activated if it is
powered when it is not rigidly attached to the vehicle,
resulting in unexpected deployment and possible in-
jury.
Step
ActionValue(s)YesNo
1Visually inspect the connector and the wiring of pas-
senger belt pretensioner. Is the connector discon-
nected?–Connect the
connector.Go to Step 2
21. Confirm the ignition switch ”OFF”.
2. Disconnect the connector of the passenger belt
pretensioner.
3. Disconnect the connector of SDM wiring.
4. Check the resistance between the terminal 1,2
of SDM and the terminal 1,2 of passenger belt
pretensioner.Is the resistance 10KΩ?
10K ΩGo to Step 3Replace the
airbag wiring.
31. Replace the SDM.
2. Confirm the ignition switch ”ON”.
3. Erase the DTC using scan tool.
4. Perform the SIR Diagnostic System Check.
Does the DTC still exist?–Go to Step 4System is OK.
4Replace the passenger belt pretensioner.–––