2004 DAEWOO LACETTI aisin automatic transaxle

AISIN AUTOMATIC TRANSAXLE 5A2 – 189
DAEWOO V–121 BL4
5. Install the forward clutch return spring and clutch
balancer.
Notice : Be careful not to damage the lip seal of forward
clutch return spring.
6. Place brake/clutch spring compressor DW240–020
and forward clutch adapter DW240–030 on the
clutch balancer and compress the piston return
spring.
7. Using a snap ring expander, install the snap ring.
Notice : Stop the press when the clutch balancer is low-
ered to the place 1–2 mm (0.039–0.078 in.) from the snap
ring groove, preventing the clutch balancer from being de-
formed.
Notice : Do not expand the snap ring excessively.
8. Install the 3 plates, 3 discs and flange.
S Install in order: P
D
P
D
P
D – F
(P = Plate, D = Disc, F = Flange)
9. Using a screwdriver, install the snap ring.
10. Check that the end gap of the snap ring is not
aligned with one of the cutouts.

5A2 – 190IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
11. Install the plate, 2 discs and 2 flanges.
S Install in order: F
D
P
D – F
(P = Plate, D = Disc, F = Flange)
12. Using a screwdriver, install the snap ring.
13. Check that the end gap of the snap ring is not
aligned with one of the cutouts.
WARNING : USE CAUTION WHEN CHECKING COM-
PONENTS WITH COMPRESSED AIR OR PERSONAL
INJURY MAY RESULT.
14. Install the forward and reverse clutch and thrust
needle roller bearing on the transaxle rear cover.
15. Using a dial indicator, measure the reverse clutch
pack clearance while applying and releasing 392
kPa (57 psi) of compressed air.
S Pack clearance: 0.40
1.00 mm (0.0157

0.0394 in.) If the pack clearance is less than the
limit of pack clearance, parts may have been
assembled incorrectly, so check and reassemble
again.
If the pack clearance is non–standard, select
another flange.
There are 4 flanges in different thickness.
S Flange Thickness: mm (in.)
No
ThicknessNoThickness
13.0 (0.118)33.4 (0.134)
23.2 (0.126)43.6 (0.142)

AISIN AUTOMATIC TRANSAXLE 5A2 – 191
DAEWOO V–121 BL4
16. Install the forward and reverse clutch and thrust
needle roller bearing on the transaxle rear cover.
17. Using a dial indicator and measuring terminal
DW240–120, measure the forward clutch pack
clearance while applying and releasing 392 kpa (57
psi) of compressed air.
S The forward and reverse clutch will come out as
you apply the compressed air. Therefore, while
the checking is being done, press on the input
shaft of the forward and reverse clutch using
stamping machine or alike so that the pressure
is not applied on the forward and reverse clutch.
S Pack clearance: 1.1–1.5 mm (0.043
0.059 in.)
If the pack clearance is less than the limit of
pack clearance, parts may have been as-
sembled incorrectly, so check and reassemble
again.
If the pack clearance is non–standard, select
another flange.
There are 4 flanges in different thickness.
S Flange Thickness: mm (in.)
No
ThicknessNoThickness
13.0 (0.118)33.4 (0.134)
23.2 (0.126)43.6 (0.142)

5A2 – 192IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
COUNTER DRIVEN GEAR
1. Outer Tapered Roller Bearing Race
2. Tapered Roller Bearing
3. Counter Drive Pinion4. Counter Driven Gear
5. Tapered Roller Bearing
6. Outer Tapered Roller Bearing Race

AISIN AUTOMATIC TRANSAXLE 5A2 – 193
DAEWOO V–121 BL4
Tools Required
DW240–160 Transaxle Case Outer Tapered Roller Bear-
ing Race Adapter
DW240–170 Adapter Handle
Disassembly Procedure
1. Using a suitable puller, remove the tapered roller
bearing from the transaxle case side.
2. Using a press, remove the counter driven gear.
3. Using a suitable puller, remove the tapered roller
bearing.
4. Using a suitable puller, remove the outer tapered
roller bearing race and shim from the transaxle
case.
5. Using a suitable puller, remove the outer tapered
roller bearing race from the transaxle housing.
Assembly Procedure
1. Install a new outer tapered roller bearing race into
the transaxle housing.
Notice : Press–fit the outer tapered roller bearing race un-
til it contacts the transaxle housing.

5A2 – 194IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
2. Install the shim to the transaxle case.
S First install a shim of the same thickness as be-
fore.
3. Using transaxle case outer tapered roller bearing
race adapter DW240–160 and adapter handle
DW240–170, press in a new outer tapered roller
bearing race into the transaxle case.
Notice : Press–fit the shim until it contacts the transaxle
case.
4. Using a press, install the counter driven gear.
5. Using a press, install a new tapered roller bearing
of the transaxle case side.
6. Using a press, install a new tapered roller bearing
of .the transaxle housing side.

AISIN AUTOMATIC TRANSAXLE 5A2 – 195
DAEWOO V–121 BL4
VALVE BODY
1. Manual Valve
2. Upper Valve Body
3. Valve Body Plate
4. No1. Solenoid Valve
5. O–Ring
6. No2. Solenoid Valve7. O–Ring
8. Pressure Control Solenoid Valve
9. Lower Valve Body
10. Timing Solenoid Valve
11. O–Ring
12. Lock–up Solenoid Valve

5A2 – 196IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
1. Cover
2. Gasket
3. Cover Plate
4. Gasket
5. Pressure Relief Valve Spring Seat6. Spring
7. Ball
8. Check Ball
9. Spring
10. Check Valve