2004 DAEWOO LACETTI speed sensor

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 119
DAEWOO V–121 BL4
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
3rd gear.
S High line pressure
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction hasnot occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Check for intermittent input speed sensor or output
speed sensor circuit problems.
S Check for possible incorrect calibration.
DTC P0732 – Gear 2 Incorrect Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
2Visually inspect the transaxle cooling system for
fluid leaks.
Was condition found and corrected?–Go to Step 7Go to Step 3
3Has the transaxle fluid checking procedure been
performed?–Go to Step 4Go to Trans-
axle fluid check
procedures
41. Using the scan tool record each transaxle drive
range.
2. Drive the vehicle in transaxle gear ranges 1,2,3
and D with TP greater than 15% and vehicle
speed greater than 16km/h(10mph) for five
seconds.
Does commanded gear ratio match ranges as
shown?1st = 2.719
2nd = 1.487
3rd = 1.000
4th = 0.717Refer to Diag-
nostic AidsGo to Step 5
5Perform line pressure check.
Was the condition found and corrected?–Go to Step 7Go to Step 6
6Check for possible clutch slippage.
Was the condition found and corrected?–Go to Step 7–
71. After the repair, use a scan tool
clear info"
function and road test the vehicle.
2. Review the
DTC info".
Has the last test failed or is the current DTC dis-
played?Replace trans-
axle assemblyRepair verified
exit DTC chart

5A1 – 120IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0733
GEAR 3 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716, and
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 121
DAEWOO V–121 BL4
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear.
S High line pressure
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction hasnot occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Check for intermittent input speed sensor or output
speed sensor circuit problems.
S Check for possible incorrect calibration.
DTC P0733 – Gear 3 Incorrect Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
2Visually inspect the transaxle cooling system for
fluid leaks.
Was condition found and corrected?–Go to Step 7Go to Step 3
3Has the transaxle fluid checking procedure been
performed?–Go to Step 4Go to Trans-
axle fluid check
procedures
41. Using the scan tool record each transaxle drive
range.
2. Drive the vehicle in transaxle gear ranges 1,2,3
and D with TP greater than 15% and vehicle
speed greater than 16km/h(10mph) for five
seconds.
Does commanded gear ratio match ranges as
shown?1st = 2.719
2nd = 1.487
3rd = 1.000
4th = 0.717Refer to Diag-
nostic AidsGo to Step 5
5Perform line pressure check.
Was the condition found and corrected?–Go to Step 7Go to Step 6
6Check for possible clutch slippage.
Was the condition found and corrected?–Go to Step 7–
71. After the repair, use a scan tool
clear info"
function and road test the vehicle.
2. Review the
DTC info".
Has the last test failed or is the current DTC dis-
played?Replace trans-
axle assemblyRepair verified
exit DTC chart

5A1 – 122IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
RangePark/
Neutr
alRever
seD321
GearNR1st2nd3rd4th1st2nd3rd1st2nd1st
Solenoid Valve
1ONON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFFON/
OFF
Solenoid Valve
2ONONONOFFOFFOFFONOFFOFFONOFFON
Line Pressure
Control Sole-
noid Valve 3
(EDS 3)OFFOFFOFFONON/
OFFON/
OFFOFFONON/
OFFOFFONOFF
Line Pressure
Control Sole-
noid Valve 4
(EDS 4)ONOFFONONONOFFONONONONONON
Line Pressure
Control Sole-
noid Valve 5
(EDS 5)OFFOFFONONOFFOFFONONOFFONONON
Line Pressure
Control Sole-
noid Valve 6
(EDS 6)ONOFFONONONOFFONONONONONON
Brake BAAAAAAAA
Brake CH
Brake DH
Clutch EAAAAAA
Brake FHHHHHHH
Lock–up
ClutchA
A = Applied
H = Holding
ON = The solenoid is energized.
OFF = The solenoid is de–energized.
** = Manual Second–Third gear is only available above approximately 100 km/h (62 mph).
*** = Manual First–Second gear is only available above approximately 60 km/h (37 mph).
Note : Manual First–Third gear is also possible at high vehicle speed as a safety feature.
DIAGNOSTIC TROUBLE CODE(DTC) P0734
GEAR 4 INCORRECT RATIO
Circuit Description
The TCM uses transaxle input speed information and out-
put speed sensor to control line pressure, TCC apply and
release and transaxle shift patterns. This information is
also uses to calculate the appropriate operating gear ra-
tios and TCC slippage. Conditions for Setting the DTC.
Conditions for Setting The DTC
S Time since TCM reset is greater than 500 msec.
S Time since shift end is greater than 500 msec.S Transmission oil temperature is greater than –10°C
(14°F).
S System voltage is greater than 9 volts.
S No input speed error DTCs P0715, P0716, and
P0717.
S Output speed is greater than 256 rpm.
S Input speed is greater than 400 rpm.
S No gear shift active.
Action Taken When The DTC Sets
S The Malfunction Indicator Lamp(MIL) will illuminate.

ZF 4 HP 16 AUTOMATIC TRANSAXLE 5A1 – 123
DAEWOO V–121 BL4
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
S High line pressure
Conditions for Clearing the MIL/DTCS The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycle.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.
Diagnostic Aids
S Check for intermittent input speed sensor or output
speed sensor circuit problems.
S Check for possible incorrect calibration.
DTC P0734 – Gear 4 Incorrect Ratio
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to ”On–
Board Diagnos-
tic System
Check”
2Visually inspect the transaxle cooling system for
fluid leaks.
Was condition found and corrected?–Go to Step 7Go to Step 3
3Has the transaxle fluid checking procedure been
performed?–Go to Step 4Go to Trans-
axle fluid check
procedures
41. Using the scan tool record each transaxle drive
range.
2. Drive the vehicle in transaxle gear ranges 1,2,3
and D with TP greater than 15% and vehicle
speed greater than 16km/h(10mph) for five
seconds.
Does commanded gear ratio match ranges as
shown?1st = 2.719
2nd = 1.487
3rd = 1.000
4th = 0.717Refer to Diag-
nostic AidsGo to Step 5
5Perform line pressure check.
Was the condition found and corrected?–Go to Step 7Go to Step 6
6Check for possible clutch slippage.
Was the condition found and corrected?–Go to Step 7–
71. After the repair, use a scan tool
clear info"
function and road test the vehicle.
2. Review the
DTC info".
Has the last test failed or is the current DTC dis-
played?Replace trans-
axle assemblyRepair verified
exit DTC chart

5A1 – 134IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1671
CAN TRANSMIT MESSAGE FAILURE
Circuit Description
The transaxle control module(TCM)is an electronic device
which monitors inputs to control various transaxle func-
tions including shift quality and transaxle sensors,
switches, and components to process for use within its’
control program. Based on this input information, the TCM
controls various transaxle output functions and devices.
Information is transmitted between the TCM and ECM
through the CAN. Information is as follows:
S Engine Malfunction Signal.
S Engine Speed.
S Engine Output Torque Reduction Signal.
S Engine Coolant Temperature.
Conditions for Setting the DTC
S System voltage is too high or too low.
S CAN transmitting wiring harness shortage or open.S TCM or ECM is defective.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The malfunction indicator lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycles.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.

5A1 – 136IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1672
CAN BUS OFF FAILURE
Circuit Description
The transaxle control module(TCM)is an electronic device
which monitors inputs to control various transaxle func-
tions including shift quality and transaxle sensors,
switches, and components to process for use within its’
control program. Based on this input information, the TCM
controls various transaxle output functions and devices.
Information is transmitted between the TCM and ECM
through the CAN. Information is as follows:
S Engine Malfunction Signal.
S Engine Speed.
S Engine Output Torque Reduction Signal.
S Engine Coolant Temperature.
Conditions for Setting the DTC
S System voltage is too high or too low.
S CAN transmitting wiring harness shortage or open.S TCM or ECM is defective.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The malfunction indicator lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycles.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.

5A1 – 138IZF 4 HP 16 AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE(DTC) P1673
CAN RECEIVE ECM MESSAGE FAILURE
Circuit Description
The transaxle control module(TCM) is an electronic de-
vice which monitors inputs to control various transaxle
functions including shift quality and transaxle sensors,
switches, and components to process for use within its’
control program. Based on this input information, the TCM
controls various transaxle output functions and devices.
Information is transmitted between the TCM and ECM
through the CAN. Information is as follows:
S Engine Malfunction Signal.
S Engine Speed.
S Engine Output Torque Reduction Signal.
S Engine Coolant Temperature.
Conditions for Setting the DTC
S System voltage is too high or too low.
S CAN transmitting wiring harness shortage or open.S TCM or ECM is defective.
S Immediately after the above condition occurs.
Action Taken When The DTC Sets
S The malfunction indicator lamp(MIL) will illuminate.
S The TCM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Failure Records buffer.
S Adopt Emergency/ Substitute mode and constant
4th gear by hydraulic control.
S After ignition OFF/ON : 3rd gear by hydraulic con-
trol. Possible P, R and N also possible.
Conditions for Clearing the MIL/DTC
S The MIL will turn OFF when the malfunction has
not occurred after three–ignition cycles.
S A history DTC will clear after 40 consecutive warm
up cycles without a fault.
S Using a scan tool can clear history DTCs.