2004 DACIA SOLENZA gearbox

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 28
C.V. 1175
C.V. 31-01
Mount the 5-th gear fix pinion on the sec-
ondary shaft by means of the C.V. 1175 de-
vice. Dismount the C.V. 1175 device and mount
the secondary shaft screw, oiled with 3 drops
of LOCTITE FRENBLOC.
Remount on the primary shaft, observing
the following sequence :
- the support washers (with the larger side
towards the pinion ) - the bushing under the pinion;
- the fre e 5 th pinion equipped with its
synchroni ser ring ;
- the 5-th gear hub equipped with its spring
- the fork together with the 5 th sliding
collar. Engage the 1-st gear with the gear lever and
the 5 th gear by sliding the 5-th gear fork on its
axle. Mount the nut and the screw and tighten them
at the required moment: - primary shaft nut : 19 daNm;
- secondary shaft screw : 7 daNm.
Mount the pin of the 5 th gear fork by means
the CV 31 01 device.
Gearb ox dismounting
vnx.su

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 29
Observe the mounting direction, the pin slot must be oriented towards the back cap.
Bring the gearbox in the neutral position
M ount a new gasket to ensure the back cap sealing.
Mount the back cap with the A groove in the primary shaft, and the oiling collector in the B
oil collecting groove, and tighten the screws at the required moment of 2,5 daNm .
Check the correct gears shifting.
Mount the reverse driving connector.
Mount the clutch control fork and the pressure bearing.
G earbox dismounting
vnx.su

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 30
Replacement of the planetary
sealing gasket (on the vehicle)
SDV-uri SPECIALE NECESARE
C. V. 945 Mandrin montare garniturã etanºare planetarã
TIGHTENING MOMENTS (d aNm)
Shoc k absorber attachment
nut on steering knuckle 7.5
Wheel attachment screws 7.5
Oil draining plug 2.5
1
DISMOUNTIN G
Place the vehicle on a two-columns
elevator.
Dismount the right front wheel.
Drain the oil off the gearbox.
Dismou nt :
- the wheel protector
- the shock absorber attachment nuts
(1) on steering knuckle.
REMOUNTING
Lubricate with oil the new sealing gasket.
Mount the sealing gasket by means of the
C.V. 945 device.
M ount the protector (A) lubricated with
oil, on the planetary shaft and position the
gasket (C) by means of the device (B).
Rock the steering knuckle and disconnect
the planetary transmission from the gearbox.Remove
the “O” ring off the planetary shaft,
then, by means of a pins mandrel and a
hammer,
is gently hit in order to make it pivoting in its place.
Remove the sealing gasket by means of a
pliers, taking c are not t o damage the planetary
pinion grooves.
vnx.su

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 31
Replacement of the planetary
sealing gasket (on the vehicle)
Position and mount the planetary transmission on the planetary pinion.
Perform the dismounting operations in the reverse order
Tighten at the required moment the screws and the nuts.
Perform the oil filling of the gearbox.
Check the gearbox sealing.
vnx.su

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 32
Replacement of the 5-th gear synchroniserand pinion (on the vehicle
)
1
NECESSARY SPECIAL TOOLS
C. V. 22 – 01 Bearings extractor body
C. V. 31 - 01 Mandrels set for elastic pins
C. V. 1000 Extractor for the 5-th gear fix pinion C.V.
1 170 Extractor for the 5-th gear hub.
C. V. 1 175 Screw for mounting the 5-th gear fix pinion
Tightening moments (daNm)
Primary shaft nut 19
S econdary shaft screw 7
Wheel attachment screws 7.5
Back cap attachment screws 2.5
Oil draining plug 2.5
DISMOUNTIN G
Place the vehicle on a two columns
elevator.
Dismount the front left wheel.
Drain the oil off the gearbox.
Disconnect the connector of the reverse
driving contact. Dismount the cross-tie rod (1).
Dismount the attachment screws of the
back cap. Re m ove t he ba c k c a p on t he ge a rbox
horizontal axle direction, because the cap is
provided with an oiling groove ( A), which is
penetrating into the primary shaft.
Engage the 1-st gear.
Dismount the elastic pin of the 5-th gear fork
by means of the m andrel C.V. 31 – 01.
Engage the 5-th gear by hand.
Dismo unt :
- the nut from the primary shaft and t he
screws from the secondary shaft. - the 5-th gear fork and sliding collar.
vnx.su

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 33
Replacement of the 5-th gear synchroniserand pinion (on the vehicle
)
C.V. 1170 C.V. 1000
C.V.
22-01
C.V. 1175
C.V. 31-01
Bring the gearbox in the neutral position.
Extract the synchroniser hub by means of the
extractor C.V. 1170.
Dismount the 5-th gear assembly
Dismount the 5-th gear fix pinion by means of
the extractor C.V. 1000 and the body extractor
C.V. 22 - 01.
REMOU NT I NG
Mount on the secondary shaft the 5-th gear
fix pinion by means of the C.V. 1175 device
Dismount the C.V. 1175 device.
A pply three drops of Loctite
FRENBLOC on t he scre w thread of the
secondary shaft. Mount the secondary shaft screw.
vnx.su

CV JH3 - 05121
MECHANICAL GEARBOX
21 - 34
Replacement of the 5-th gear synchroniserand pinion (on the vehicle
)
C.V. 31-01
Mount on t he pri m a ry sha ft , i n t he
following sequence: - the support washer (with the l arger side
towards the pinion ) - the bushing under the pinion;
- the free 5 th pinion equipped with its
synchroni ser ring ;
- the fork together with the 5-th gear sliding
collar;
- the primary shaft nut.
Engage t he 1-st gear with the ge ar l ever
and the 5-th gear by sliding the 5-th gear fork
on its axle. Tighten at the required moment:
- the primary shaft nut: 19 daNm;
- the secondary shaft screw: 7 daNm.
Mount the pin of the 5-th gear fork by
means the CV 31 01 device.
The pin slot must be oriented towards the
back cap. Bring the gearbox in the neutral position
and check the engagement of all speed gears. M
ount a new tore gasket to ensure the back
cap sealing. Mount the back cap with the ( A) groove in
the primary shaft, and the oiling collector in the
(B) oil collecting gr o ove.
Tighten the back cap screws at the re quired
moment of 2,5 daNm .
Mount the reverse driving contact connector.
Check the correct gears shifting.
Perform the filling with oil of the gearbox .
Check the gearbox sealing.
M ount the two cross-tie rods.
Mount the right front wheel.
T ighten the screws and the nuts at the required
moment.
vnx.su

TRANSM ISSION
29
29 - 1
Front transversal transmission
DISMOUNTING - THE SIDE TO W HEEL
Loosen the left wheel screws.
Lift the vehicle on an elevator with two columns.
Dismount the wheels.
Dismount the screws that attach the brake disk assembly on the steering knuckle.
U nscrew the transmission nut by means of the RO 604 – 01 device.
Dismou nt :
- the nut of the steering ball joint;
- steering ball j oint from the steering knuckle, by means of the PF 476 extractor;
- the attachment screws of the steering knuckle on the shock absorber end. SPECIAL TOOLS
RO 604-01 Hub immobilizing device
PF 476 Ball joint extractor
TIGHTENING MOMENTS (daN/m)
T ransmission nut 28
S crew for fixing the bellows lid on the gearbox 2,5
Wheels attachment screw 7,5
Screws, nuts for fixing the stee ring knuckle on the shock absorber 10,5
S crew for fi xing the caliper on the steering knuckle 6,5
Nut for steering ball joint 4
Push the transmission in the steering knuckle and incline the latter.
Dismount the transmission, the wheel side.
vnx.su