2004 Citroen XSARA Kfw engine

Downloaded from www.Manualslib.com manuals search engine 288
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Clutch cable.
Removing.
Uncouple the cable from the lever (1).
Unclip the cable from the gearbox by actioning
the side tabs
(2).
Detach the cable from the bulkhead.
Remove the clip
(3).
Uncouple the cable from the clutch pedal.
B2BP001CB2BP002C
XSARA XSARA PICASSO
B2BP02VC
B2BP02WC
«PUSH» clutch
«PULL» clutch
B2BP03BCB2BP002C

Downloaded from www.Manualslib.com manuals search engine 289
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Refitting.
Place the pedal in the high position (contact at “a”).
Attach the cable yoke on the hook of the clutch pedal.
Fit a new clip
(3).
Fit the endpiece (4)to the bulkhead (fit with G6grease).
Clip the endpiece (5)on the gearbox.
Couple the cable to the lever (1).
Depress the clutch cable several times to lodge the cable in place.
Check that the endpiece (4) is correctly lodged on the bulkhead.
Check the operation of the automatic adjusting system.
After fitting the cable, pull the clutch lever in the inverse direction
(direction F), the lever should
move back when pulled by hand.
Press the clutch pedal very lightly and repeat the same operation. The lever should not move
back.
WARNING:If a system blockage is detected when checking, or if the pedal has been removed,
the pedal position must be adjusted. The correct positioning of the pedal is obtained by the
angular displacement of the stop supports
"a"and "b".
B2BP03CD
XSARA XSARA PICASSO
«PUSH» clutch
«PULL» clutch
B2BP03DD

Downloaded from www.Manualslib.com manuals search engine 290
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH CONTROLS: FEATURES / CHECKS AND ADJUSTMENTS
Engines: KFW NFU 6FZ RFN RFS 8HX 9HZ 9HY WJY RHY RHZ
Adjusting the pedal height.
Loosen the nut (6)and the screw (7).
Using a lever, raise the stop support (8)to its highest position. In this position, there should be a substantial free
play in the pedal.
Lower the support until there is a free play of
2 ± 1 mm.
Tighten the nut (6) and the screw (7).
Check that the clutch cable sleeve can move freely.
At rest, the clutch cable sleeve should be free and able to lengthen and shorten.
Clutch pedal travel.
The automatic clutch wear adjustment system has no manual adjustment.
Pedal travel is identical on all models:154 ± 5 mm.
The adjustment is achieved by reducing the length of the cable sleeve.
WARNING:Automatic adjustment of the pedal travel is accompanied by a modification of the curvature of the
cable sleeve. Do not add any supplementary fixing points or alter the routing in any way.
«c»Routing of new cable.«b»Routing after adjustment of play.«x» Clutch wear.
B2BP03ECB2BP03FD
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 298
CLUTCH
GEARBOX
TRANSMISSION
GEARBOX AND TYRE SPECIFICATIONS
Petrol
XSARA
Engine type
Tyresrolling Circumference
Speedometer ratio Gearbox type
Gearbox ident. plate
Reduction box torque
Engine type
Tyresrolling Circumference
Speedometer ratio Gearbox type
Gearbox ident. plate
Reduction box torque1.4i1.6i 16V
AUTOMATIC AUTOMATIC
2.0i 16V
KFW NFU RFN RFS
195/55 R15 1,815 m
MA/5 AL4 BE4/5 AL4 BE3/5
20 CP 13
(1)20 CP 51 (2)20 TP 49
20 DL 40
20 TP 4720 TE 47
16x65 21x73 19x72 23x73 14x62
21x18 24x21 22x19 24x21 22x19
Diesel
1.9 D
1.4 HDi2.0 Hdi
WJY 8HZ RHY (3) RHZAUTOMATIC
195/55 R15 – 1,815 m
BE4/5
AL4
20 DL 41
19x75
22x19 20 DM 54 20 DL 42
19x7020 DM 10
17x6120 TP 48
14x62
22x19
NOTE:(RHY engine BE4/5 gearbox) (1) Estate = 20 CP 44 (16x65) (21x18) (2) DAIC = 20 CP 52 (14x60) (21x18) (3)XSARA DAIC RHD = 20 DM 08Right hand drive: 6FZRFN= 20 DM 03 WJY= 20 DM 05 8HZ= 20 DM 53 RHY = 20 DM 07 RHZ= 20 DM 11

Downloaded from www.Manualslib.com manuals search engine 304
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX
Engines: KFW NFU
«a»Identification label.
«b»Location for engraving of serial and gearbox nos.
B2CP3HTC
XSARA

Downloaded from www.Manualslib.com manuals search engine 305
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX
Engines: KFW NFU
(1)Primary shaft.(2)Clutch bearing guide.(3)Clutch housing.(4) Gearbox casing.(5) Intermediate plate.(6)Bearing retaining clip.(7) Drive pinion (5th gear).(8) Secondary shaft.(9)5th gear synchroniser.(10)Driven pinion (5th gear).(11)Driven pinion (4th gear).(12)3rd / 4th gear synchroniser.(13)Driven pinion (3rd gear).(14)Driven pinion (2nd gear).(15) 1st / 2nd gear synchroniser and reverse gear driven pinion.(16) Driven pinions (1st gear).(17)Differential gearwheel.(18)Satellite pinions.(19)Planet pinions.(20)Counter drive.(21)Speedometer screw.(22) Differential housing.B2CP167P
XSARA

Downloaded from www.Manualslib.com manuals search engine 306
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX
Engines: KFW NFU
Tightening torques (m.daN).
(23)
Clutch bearing guide (3 fixing screws): 0,6 ± 0,15.
(24)
Intermediate plate (11 fixing screws): 5 ± 0,5.
(25)
Rear cover (3 fixing screws):2,2 ±0,2.
(26)
Bearing retaining clip (4 fixing screws): 1,8 ± 0,2.
(27)
Secondary shaft nut (1 nut):14 ± 1.
(28)
Gearbox casing (15 fixing screws):1,8 ±0,2.
B2CP167P
XSARA

Downloaded from www.Manualslib.com manuals search engine 307
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX
Engines: KFW NFU
(29)Topup plug (x1): 2,5 ± 0,5.
(30)Drain plug (x1): 2,5 ± 0,5.
(31)Reverse gear switch (x1): 2,5 ± 0,5.
Strengthened MA gearboxes are marked with the letter «B»or «C»:«B»= Differential diameter 77 mm+ strengthened bearings.«C»= Differential diameter 77 mm+ strengthened bearings + strengthened
intermediate plate.
NOTE:All vehicles are equipped with clutch control by cable.
Features.
This gearbox:
has no adjustment.
has a reverse gear braking device
(5th gear synchroniser).
has a device for prohibiting a change from 5th gear into reverse gear.
The clutch control has a balljoint mounted declutch fork.
Lubrication.
Oil capacity : 2 ± 0,15 Litres.
Checking the oil level : Every 37,500 miles.
Lubrication interval : Lubricated «for life».
B2CP169D
XSARA