Page 431 of 523
Downloaded from www.Manualslib.com manuals search engine 427
BRAKES
B3FP161D
BRAKE SPECIFICATIONS
Braking circuit without ABS REF (drum brakes at the rear)
Braking system specifications
Braking circuit at «X».
Front brakes with ventilated discs
(*).
Rear brakes with eitther drums or discs
(*).
Handbrake lever controlling cables acting on the rear
wheels.
The compensator and main brake limiter functions are
assured by the
ABS EBD system.
NOTE: REF= Electronic Brakeforce Distribution.
(*)= according to version.
C3 C3 PLURIEL
Page 484 of 523
Downloaded from www.Manualslib.com manuals search engine 480
ELECTRICAL
SYSTEM
CHARGING CIRCUIT ALTERNATOR WITH MONO FUNCTION REGULATOR
Checking the alternator output.
Connect as shown in the diagram opposite, using an ammeter (A), a voltmeter (V),
and a rheostat
(R)or a Volt/Ammeter/Rheostat combination.
Referring to the vehicle’s equipment specification
(see table opposite), adjust the
engine speed and rheostat charge to obtain
U = 13.5 V.
Reminder:The excitation energising current will flow through the warning lamp;
check that the warning lamp comes on when the ignition is switched on. It shouldgo out when the engine has started
(accelerate slightly).
Checking the voltage regulator.
Set the rheostat to zero and disconnect all the electrical consumers.
Display
3000alternator rpm. If U alternator is > 14.7 V, the regulator is faulty.
Note:These tests should be performed with the engine hot and the battery fully
charged.
Method of reading the alternator speed.
Fit a reflecting shim on the pulley of the alternator.
Adjust a stroboscope to the frequency equivalent to the control speed.
(e.g. 2000 rpm = 2000/60 = 83 Hz).
Adjust the engine speed so that the shim appears fixed.
D1AP025C
A: Ammeter.B:Battery.G: Generator.L: Warning lamp.K1and K2:Switch.R: Electric charge.S:Shunt 200mV/200A.V:Voltmeter.1 : Alternator.
Page 486 of 523
Downloaded from www.Manualslib.com manuals search engine 482
ELECTRICAL
SYSTEMNAGARES 960411 P
CARTIER 735068
NAGARES 960411 P
CARTIER 735068
NAGARES 960411 P
NAGARES 960411 P
CARTIER 735068
NAGARES 960411 P
NAGARES 960411 P
CARTIER 735068
CARTIER 735068
NAGARES 960411 P
CARTIER 735068
NAGARES 960411 P
CARTIER 735068
NAGARES 960411 P NGK YE04
NGK YE04
NGK YE04
BERU 0 100 226 371
CHAMPION CH 185
NGK YE04
CHAMPION CH170
CHAMPION CH 170
CHAMPION CH 170
PRE HEATING AND STARTING SYSTEMSTOUS TYPES
Vehicles models
Pre heater plugs Pre heater control unitPre/Post heating (pre-heating duration at 20°C)
C2
C3
XSARA
PICASSO1.4 HDi
1.4 HDi
1.4 HDi 16V
1.9 D
1.4 HDi
2.0 HDi
2.0 HDi
2.0 HDi8HX
8HW
8HX
8HV
8HY
WJY
8HZ
RHY
RHZ
RHY
Controlled by the diesel injection ECU.
10s / 150s
Controlled by the diesel injection ECU.
Page 502 of 523
Downloaded from www.Manualslib.com manuals search engine 498
AIRCONAIRCON
AIR CONDITIONING SYSTEM R 134.a
Testing procedure
Conditions inside the vehicle.
Positions of the air conditioning controls:
Maximum cold.
Maximum blower power.
Air distribution on
«ventilation»with the air vents open.
Position the air inlet flap to outside air.
WARNING:For RFTA (1), disconnect the air inlet motor connector, first
ensuring that it is in the outside air position.
(1) RFTA= Fully automatic air conditioning.
Test procedure.When all these conditions are met, proceed in the following order:
Measure the temperature in the workshop approx. one metre in front of
the vehicle’s air inlet grille.
Start the engine
(without the air conditioning, or the blower, operating)and wait for the cooling fan slow speed to trigger (should the engine tem
perature not rise sufficiently, it is permissable to increase the engine
speed to 2000 rpm)
.
Once it is sufficiently hot in the engine compartment, return the engine
to idle and commence the test.Switch on the air conditioning and adjust the engine speed to
2500 rpm.
In an ambient temperature of 40°C, the engine speed will be brought
down to 2000 rpm, in order for the pressure safety threshold to cut off the
compressor.
For further temperatures/pressures: see Tables and Graphs on following
pages
221, 222 and 226.
After
3 minutesof operation, note down the following 3 parameters:
The temperature of the blown air coming out of the 2 central air vents
(take the average).
The high pressure, via the intermediary of the clickfit union (at the
pressure reducer inlet).
The low pressure, via the intermediary of the clickfit union (at the pressure
reducer outlet).NOTE:The low and high pressures are absolute pressures.
When measuring the blown air temperatures, avoid any contact between
the thermocouple and the air vents.
At the conclusion of the test involving vehicles with
«RFTA»
ALL TYPES
