2004 Citroen C3 PLURIEL Rod

Downloaded from www.Manualslib.com manuals search engine 86
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines: 8HV 8HY
RH engine support
Screw (1) : 6 ± 0,6
Screw (2) : 6 ± 0,6
RH lower engine support
Screw (3) : 5,7 ± 0,5
LH upper engine support
Screw (7):6 ±0,6
Screw (8) : 5,5 ± 0,5
LH lower engine support
Screw (6) : 5,4 ± 0,5
Torque reaction rod
Screw (4) : 6 ± 0,6
Screw (5) : 6 ± 0,6
B1BP2MNP
C3

Downloaded from www.Manualslib.com manuals search engine 89
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
CYLINDER HEAD (mm)
Engine types KFW NFV NFU
Maximum permissible bow0,05
Gasket surface regrinding 0,20
TIGHTENING TORQUES (m.daN)
Crankshaft bearing Pretightening 2 ± 0,2 2 ± 0,2
screws Angular tighten 45° 50° ± 5°
Connecting rod screwsTightening3,8 ±0,4
Flywheel screw Tightening 6,5 ± 0,7
Crankshaft pinion screw Pretightening
Angular tighten10 ±1
Camshaft pulley screw Pretightening
Angular tighten 8 ± 0,8
Camshaft hubs 8 ± 0,8
Camshaft hub screwTightening1 ± 0,1
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 90
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
CYLINDER HEAD (mm)
Engine types 6FZ RFN RFS WJY RHY RHZ
Maximum permissible bow 0,05 0,03
Gasket surface regrinding 0,30 0,20 0,40
TIGHTENING TORQUES ( m.daN)
Pretightening (1) Ø 11 : 1 ± 0,1 2 ± 0,1 2,5 ± 0,3
(2) Ø 6 : 1 ± 0,1
Slackening Ø 11 (only)
Tightening Ø 11 to 1 ± 0,1 8,5 ± 0,8 7 ± 0,7
Crankshaft then to 2 ± 0,1
bearing screws Tightening Angular Ø 11 at 70° ± 5° 60° ± 6° 60° ± 6°
Tightening Ø 6 to 1 ± 0,1
Pretightening 1 ± 0,1 4 ± 0,4 2 ± 0,2
ConnectingSlackening 180° (1/2 turn)
rod screws Tightening 2,3 ± 0,2 2,3 ± 0,2 2± 0,2
Angular tightening46°±5°46° ±4,6° 70° ± 7° 70° ± 7°
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 91
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines: 9HZ 9HY
Torque reaction rod
1 : 5,4 ± 0,8
2 : 5,4 ± 0,8
13 : 6 ± 0,9
LH upper engine support
3 : 2,1 ± 0,2
4 : 5 ± 0,5
LH lower engine support
5 : 2,1 ± 0,2
6 : 5,7 ± 0,8
RH lower engine support
7 : 5,5 ± 0,5
RH engine support
8:4,5 ±0,4
9 : 4,5 ± 0,6
10:2,5 ±0,6
11:2,1 ± 0,2
12 : 6,1 ± 0,6
B1BP2Z4P
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 92
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines9HZ 9HY
Crankshaft
Bearing cap fixing screw
Pretightening1 ± 0,2
Slackening180°
Tightening3 ± 0,3
Angular tightening140°
Con rod screws
Tightening1 ±0,1
Angular tightening100 ±5°
Accessories drive pulley
Pretightening3,5 ± 0,4
Angular tightening190 ± 5°
Cylinder block
Sump 1,3 ± 0,1
Timing belt guide roller3,7 ± 0,3
Timing belt tensioner roller2,7 ± 0,2
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 220
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY RHZ N° RPO 9128 #
Remove:
The fixings of the pipe linking the power steering pump with the rotary valve.
The clutch lower closing plate.
Lock the engine flywheel, using tool
[6].
Remove the screw (8).
Refit the screw (8)without its thrust washer.
Remove:
The accessories pulley
(9), using tool[8].
Tool [6].
The lower torque reaction rod.
Support the engine by means of a workshop hoist.
Remove:
The bearing shell fitting
(10).
The nut (12).
Screws (11).
The bracket (13).
NOTE:Lift then lower the engine with the workshop hoist, to have access to the
timing cover fixing screws.
Remove:
The intermediate timing cover.
The lower timing cover.
B1CP04BCB1BP2R3CB1BP2R4C
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 269
INJECTION
CHECKING THE AIR SUPPLY CIRCUIT
Engines: RHY RHZ
XSARA PICASSO
Tools.
[1]Manual vacuum pump : FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness requirements.
Vacuum pump.
Connect the tool [1]on the vacuum pump (1).
Start the engine.
Pressure should be
0.8 barat 780 rpm.Boost pressure regulator electrovalve. Connect the tool [1]between the electrovalve (2)and the valve (3)of the boost pressure
regulator.
Compare readings with the values in the table below.
Pressure regulator valve. Connect the tool [1]on the valve (3).
Appy a pressure of 0.5 barto activate the rod "a":
Rod "a"should be moved 12 mm.
Engine speed (rpm) Pressure (Bar)
780 0,6
4000 0,25
B1HP12FD

Downloaded from www.Manualslib.com manuals search engine 270
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: 8HX 8HW
Engines: 8HV 8HY
Tools.
[1]
Manual pressurevacuum pump: FACOM DA 16
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel
injection (HDi) engines.
EGR v
alve.Connect tool [1]on the capsule takeoff (2).
Apply a vacuum of approx.0,6 barseveral times to activate the rod «a».
In abruptly suppressing the vacuum, the valve should click and lock itself back on its seating.
Regulation electrovalve (EGR).(Engine:8HX8HW).Check to be performed between the electrovalve (1)and the EGR valve (2).
Link the tool [1]in series, between the electrovalve (1)and the capsule (2).
Compare the values noted with those in the table below.
Regulation electrovalve (EGR).(Engine:8HV8HY).Check to be performed between the electrovalve (2)and the EGR valve (1).
Link the tool [1] in series, between the electrovalve (2)and the capsule (1).
Compare the values noted with those in the table below.
Engine speed (rpm) Vacuum value
780 0,5
2500 0
B1HP15GD
B1HP1K6D
C2 C3