2004 Citroen C2 clock

Downloaded from www.Manualslib.com manuals search engine ENGINE
185
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
B1EP18EC
Checking the setting (continued).
Remove:
the accessories drive belt.
the accessories drive pulley.
the lower timing cover
(3).IMPERATIVE: The magnetic track should show no signs of damage
and should not be approached by any other source of magnetism.
Reposition the screw (2).
Remove tool [3].
Rotate the engine by means of the crankshaft pinion screw (2)(clock
wise), to bring it to the pegging position.
Position the tool [4].
Peg the crankshaft pinion (1), using tool [5].
Peg the high pressure pump pinion, using tool [5].NOTE:Index «a»of the roller tensioner must be centred within the
area «b».
Check the correct positioning of index «a».
Remove tools [4]and [5].
Rotate the engine ten times.Fit the tools
[4]and [5].
If pegging is not possible, carry out the operation to remove/refit the
timing belt
(see corresponding operation).
B1JP03SCB1EP18DCB1EP18FC
C2 C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine ENGINE
187
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HX 8HW 8HZ
Setting the timing (contin
ued).
Remove the tool [3].
Rotate the engine by means of the crankshaft pinion screw
(2)(clock
wise), to bring it to the pegging position.
Peg the camshaft pulley, using tool
[4].
Peg:
The crankshaft pinion
(6), using tool [5].
The high pressure pump pinion, using tool [5].
Support the engine with the aid of a roller jack equipped with a chock.
Remove:
The RH engine support
(7).
The intermediate engine support (right hand side)(8).
B1JP03SCB1EP18DCB1EP195CB1BP2LYC
C2 C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 194
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18YD
Checks (continued).
Refit the screw (8).
Rotate the crankshaft six times
(clockwise).
IMPERATIVE: Never rotate the engine backwards.
Peg:
The camshaft, using tool
[2](oil the pegs).
The fuel high pressure pump pulley (14), using tool [3]at «c».
WARNING:The magnetic track should show no signs of damage and should not be
approached by any source of magnetism.
Peg the crankshaft at
«b», using tool [3].
IMPERATIVE:Should it be impossible to peg the camshaft, check that the
offset between the hole in the camshaft pinion and the pegging hole is not
greater than 1 mm.Otherwise repeat the operation to position the timing belt
(see corresponding
operation)
.
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
197
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18VD
Setting the timing.
Perform the preliminary operations for checking the timing up to removing tool [1]at «a»for immobiling the
engine flywheel.
Refit screw
(8).
Rotate the crankshaft to bring the camshaft towards its pegging point.
Peg the camshaft, using tool
[2](oil the pegs).
WARNING: Do not press or damage the track which is the target for the engine speed sensor (14).
Peg the crankshaft at «b», using tool [3].
Remove:
The timing protector
(13).
The engine speed sensor
(14).
Slacken the screw
(12)of the tensioner roller, keeping it slack with the aid of a hexagonal spanner at
«c».
Detension the belt by pivoting the tensioner roller
(clockwise).
Remove the timing belt, commencing with the coolant pump pinion.
Peg the pulley
(15), using a 5 mmdiameter peg at «d».
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
199
CHECKING AND SETTING THE VALVE TIMING
Engines: 8HY 8HV
B1EP18XC
Setting the timing (continued).
Chec
ks (continued).
Reposition the timing belt, belt at «e»well tensioned, in the following order:
Guide roller
(17).
Camshaft pulley
(16).
Fuel high pressure pump pulley
(15).
Coolant pump pinion
(18).
Tensioner roller
(19).
Remove the
5 mmdiameter peg at «d».
Adjusting the fitting tension of the belt.
Action the tensioner roller (19)to align the marks «f»and «g», avoiding detensioning the timing belt,
with the aid of a male hexagonal spanner, at
«c».
If this is not successful, repeat the operation to tension the belt.Hold the tensioner roller in position
(19).
Tighten the tensioner roller, tightening to
3,7 ±0,3 m.daN.
Check the position of the tensioner roller
(the alignment of the marks «f»and «g»should be correct).
Remove tools
[2]and [3].
Turn the crankshaft
six rotations(clockwise).
C3

Downloaded from www.Manualslib.com manuals search engine 203
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
Refit the screw (10).
Rotate the crankshaft six times (clockwise).
IMPERATIVE: Never turn it backwards.
Peg the camshaft at «c», using tool [2](oil the peg).WARNING:The magnetic track should not show any sign of damage and should not be
approached by any other magnetic source.
Peg the crankshaft at
«d», using tool [3].
ESSENTIAL: Should it not be possible to peg the camshaft, check that the offset bet
ween the camshaft pinion hole and the pegging hole is not more than 1 mm.If it is
more,repeat the operation to position the timing belt
(see corresponding operation).
Note:
The index «e»of the dynamic tensioner roller should be centred in the interval «d»Check the correct positioning of the index «e».
If it is not correct, repeat the operation to tension the timing belt (see corresponding operation).
Remove tools [2]and [3].
B1EP1E4DB1EP1E5C
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 207
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1EP1E6D
Refit the screw (10).
Turn the crankshaft to bring the camshaft towards its pegging point.
Peg the camshaft at
«c», using tool [2](oil the pegs).WARNING: Do not press or damage the track of the engine speed sensor target
(13).
Peg the crankshaft at «e», using tool [3].
Remove:
The timing belt protector
(13).
The engine speed sensor (14).
Slacken the screw (15)of the tensioner roller, and keep it slackened using an allen
spanner at «d».
Detension the timing belt by pivoting the tensioner roller (clockwise).
Remove the timing belt, starting with the coolant pump pinion.
Checks.
ESSENTIAL: Just prior to refitting, proceed to the checks as below.
Check:
That the rollers and the coolant pump pulley turn freely (without play and without tight
spot).
That there are no signs of oil leaks (at the crankshaft and camshaft seals).
That there are no leaks of coolant fluid(at the coolant pump).
That the track of the engine speed sensor target (15)is not damaged or scratched.
Replace any components that are defective (if necessary).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 209
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1EP1E8C
Adjusting the timing belt tension.
Act on the tensioner roller (18)to align the marks «g»and «h», avoiding detensioning the
timing belt, using an allen spanner at «d».
Should this fail, repeat the operation to tension the timing belt.Hold the tensioner roller
(18).
Tighten the tensioner roller fixing nut to 3,7 ± 0,3 m.daN.
Check the position of the tensioner roller (the alignment of the marks «g»and «h»should
be correct).
Remove tools [2]and [3].
Rotate the crankshaft six times(clockwise).
IMPERATIVE:Never rotate the engine backwards.
WARNING:
Do not touch or damage the track of the target of the engine speed sensor (14).
Peg the crankshaft, using tool
[3].
Check the position of the tensioner roller (the alignment of the marks «g»and «h»should
be correct).
If this is not the case, repeat the operation to tension the timing belt.
Peg the camshaft pulley, using tool
[2].
IMPERATIVE: Should it be impossible to peg the camshaft, check that the offset bet
ween the camshaft hole and the pegging hole is not more than 1 mm. If the offset is
too great, repeat the operation.
Remove tools [2]and [3].
XSARA PICASSO