2004 Citroen C2 wheel bolts

Downloaded from www.Manualslib.com manuals search engine 218
ENGINECHECKING AND SETTING THE VALVE TIMING
NOTE: Checking and setting the valve timing on engines: RHYRHZ N° ⁄ RPO 9127
See Mechanic’s Handbook 2003: pages 193 to196
Tools.
[1]
Belt tension measuring equipment :4122T
[2]
Tension lever:().0188.J2
[3]
Engine flywheel peg: ().0188.Y
[4]
Belt clamp: ().0188.AD
[5]
Camshaft pulley peg: ().0188.M
[6]
Engine flywheel lock: ().0188.F
[7]
Set of blocking plugs:().0188.T
[8]
Pulley extractor:().0188.P
[9]
2 mm dia.peg: ().0188.Q2Removing.
IMPERATIVE: Respect the safety and cleanliness requirements
that are specific to high pressure diesel injection (HDi) engines.
Undo the front RH wheel bolts.
Raise and support the vehicle on the front RH side.
Disconnect the battery negative terminal.
Remove:
The underengine sounddeadening.
The front RH wheel.
The front RH splashshield. The engine cover.
Unclip and move aside the cooling hose.
Remove the accessories drive belt
(see corresponding operation).
XSARA XSARA PICASSO
Engines: RHY RHZ N° RPO 9128 #

Downloaded from www.Manualslib.com manuals search engine 354
CLUTCH
GEARBOX
TRANSMISSION
DRIVESHAFTS GEARBOX
Tightening torques (m.daN)
Driveshaft
bearing Engines
V ehiclesGearboxRH side LH side Tool kitGearbox oil seal mandrels
24,5 ± 0,5
32 ± 1,5
32,5 ± 2,57114T.W
Seal extractor
RH / LH
() 0338 C
() 0338 J1
+ () 0338 J3() 0338 H1
+ () 0338 H2
() 0338 J1
+ () 0338 J2() 0338 H1
+ () 0338 H2() 0338 7114T.X
7116T Driveshaft
nut
HFX KFV KFU
8HX 8HW
NFU
KFW NFU
NFV RFS RFN 6FZ WJY
8HZ 9HZ 9HY RHY RHZ
8HV 8HY
NFU RFN RHZ
KFV MA/5
XSARA
XSARA PICASSOC2 C3 C3 Pluriel
XSARANO
2 ± 0,2
1,8 ± 0,1
2 ±0,2
1,8 ±0,1
1 ±0,1
C3
C3
XSARA PICASSO
XSARA
Tightening torque (m.daN) for wheel bolts: XSARA = 8,5 ± 0,8 XSARA PICASSO = 10 ± 1 C2 C3 C3 PLURIEL = 9 ± 1BE4/5
AL 4
C2 C3 C3 PLURIEL XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine AXLES
SUSPENSION
STEERING
356
C2 AXLE GEOMETRY
B3CP07SD
Measuring front height Measuring rear height
[1]
Gauge for measuring the wheel radius, 4 bolts, tool 8006T
Z1
= Measuring zone underneath the front subframe.Z2= Measuring zone underneath the rear sill.
Measure the radius of the front wheel
R1 Calculate dimension H1 = R1 – L1Measure the radius of the rear wheel R2 Calculate dimension H2 = R2 + L2
Value at referenceExcept CRD (*)Value at referenceExcept CRD (*)heightHFX KFV 8HX NFUheightHFX KFV 8HX NFU
(+ 6 8 mm)L1 = 142,5 mmL1 = 152,5 mm(+ 10 6 mm)L2 = 52 mm L2 = 42 mm
Compress the suspension to obtain the calculated values.
The height difference between the two axle dimensions should be less than 10 mm.(*) = CRD: Difficult road conditions.

Downloaded from www.Manualslib.com manuals search engine 366
AXLES
SUSPENSION
STEERING
C3 AXLE GEOMETRY
B3CP07SD
Measuring front height Measuring rear height
[1]
Gauge for measuring the wheel radius, 4 bolts, tool4003T or8006T (according to version).
Z1 = Measuring zone underneath the front subframe.Z2 = Measuring zone underneath the rear sill.
Measure the radius of the front wheel
R1 Calculate dimension H1 = R1 – L1Measure the radius of the rear wheel R2 Calculate dimension H2 = R2 + L2
Value at reference All types Except CRD (*) Vehicle CRD (*) Value at reference All types Except CRD (*) Vehicle CRD (*)
heightRaised suspensionRaised suspensionheightRaised suspensionRaised suspension
(+ 6 8 mm)Sports Sports
(+ 10 6 mm)Sports Sports
L1 = 142,5 mm L1 = 132,5 mm L2 = 52 mm L2 = 62 mm
(*) = CRD: Difficult road conditions.
Definition for a type of vehicle whose axles and suspensions are adapted for driving on rough roads.
Compress the suspension to obtain the calculated values. The height difference between the two axle dimensions should be less than
10 mm.
Checks at reference height

Downloaded from www.Manualslib.com manuals search engine 369
AXLES
SUSPENSION
STEERING
C3 PLURIEL
AXLE GEOMETR Y
B3CP07SD
Measuring front height Measuring rear height
[1]
Gauge for measuring the wheel radius, 4 bolts, tool 4003T
Z1
= Measuring zone underneath the front subframe.Z2 = Measuring zone underneath the rear sill.
Measure the radius of the front wheel
R1 Calculate dimension H1 = R1 – L1Measure the radius of the rear wheel R2 Calculate dimension H2 = R2 + L2
Value at referenceAll TypesValue at referenceAll Typesheight height
(+ 6 8 mm)L1 = 132,5 mm(+ 10 6 mm)L2 = 47 mm
(*) = CRD: Difficult road conditions.
Definition for a type of vehicle whose axles and suspensions are adapted for driving on rough roads.
Compress the suspension to obtain the calculated values. The height difference between the two axle dimensions should be less than
10 mm.
Checks at reference height

Downloaded from www.Manualslib.com manuals search engine 381
AXLES
SUSPENSION
STEERING
Front axle Rear axle
AXLE GEOMETRY
Reference heights
: 4300T N°RPO 9429
# Tools. [1] Gauge for measuring the radius of wheels with 4 bolts
Setting the reference height.
Front
Fr ont
Measure the dimension «R1».
Calculate the dim.
H1 = R1 L1.Measure the dimension
«R2».
Calculate the dim.
H2 = R2 + L2.
Compress the suspension until the values
(H1)and (H2)are obtained.
NOTE:The difference in height between the two sides should be less than10 mm.
XSARA
Reference heights
(in mm)115,5
90,575,5 73
8388 103 Engines2.0i 16V
(RFS)All engines (except
2.0 i 16V and CRD)All CRD
engines 2.0i 16V
(RFS)All Saloon (except
2.0i 16V and CRD)EstateAll CRD
engines
B3CP04AD

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
XSARA
Steering wheel Manual steering
MANUAL STEERING SPECIFICATIONS
(a): LHD/RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAG to steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5) Steering column to support fixing:2.3 (6)Steering cardan joint fixing:2.3
(b) = Locating bush.
The locating bush must be centred in the reference window before
tightening the cardan bolts
(6).
B3EP08PD

Downloaded from www.Manualslib.com manuals search engine 396
AXLES
SUSPENSION
STEERING
XSARA POWERASSISTED STEERING SPECIFICATIONS
Steering wheel Powerassisted steering
(a): LHD = Blue.
: RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAGto steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5)Steering column to support fixing: 2.3 (6)Steering cardan joint fixing: 2.3
(b) = Locating bush.
The locating bush must be centred in the reference
window before tightening the cardan bolts
(6).
B3EP08QD