2004 Citroen C2 locking

Downloaded from www.Manualslib.com manuals search engine 329
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Principles of adjusting the gear controls.
WARNING: Cables should be adjusted each time the gearbox, gear controls or power unit are
removed.
Principles.
Lock the gear lever in neutral position, using tool:9607T.
Place the gearbox in neutral.
Couple the cables on the lever.
Fit the balljoints on the gearbox lever.
Lock the cable lengths with the balljoint locking keys.
WARNING: Do not use any tool to unclip the balljoints.
To unlock the balljoint, press at the centre «a», then pull the balljoint upwards.
NOTE:Changing an individual balljoint is possible as long as the locking key is removed.
Unclip at «b», using two small screwdrivers.
Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3BXCB2CP3BYC

Downloaded from www.Manualslib.com manuals search engine 330
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Tools.
[1] Tool for positioning the gear lever: 9607T.
Adjustements.
WARNING: Cables should be adjusted each
time the gearbox, gear controls or power unit
are removed.
Inside the vehicle:
Remove the trim under the gear lever.
Lock the gear lever in neutral position,
using tool
[1].
Under the bonnet: Remove the air filter assembly.
Unlock the balljoint keys at «a».
Place the gear selection and control levers on
neutral.
Lock the cable lengths with the balljoint locking
keys.
Checks.
Remove the tool [1].
Check that all the gears engage without
«tightness ».
Check that the gear lever moves identically
forwards and backwards and to right and left. If it
does not, repeat the adjustment.
Refit the trim under the gear lever.
Refit the air filter assembly.
Adjusting the gear controls Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3C6CB2CP3C0C

Downloaded from www.Manualslib.com manuals search engine 332
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
Precautions to be taken.
Towing.
The front of the vehicle must be raised in order to be towed.
If the front of the vehicle cannot be raised:
IMPERATIVE: Put gear lever in position «N».
Do not add any oil.
Do not exceed
30 mphover a distance of 30 milesof maximum.
Driving.
Never drive with the ignition switched off.
Never push the vehicle to try to start it
(impossible with an automatic gearbox).
NOTE:The automatic gearbox is only lubricated when the engine is
running.
Repairs on electrical components.
Do not disconnect:
The battery when the engine is running.
The ECU when the ignition is switched on.
Before reconnecting a switch,check: The condition of the various contacts (for deformation, corrosion etc).
The presence and condition of the mechanical locking.
When performing electrical checks: The battery should be correctly charged.
Never use a voltage source higher than 16V.
Never use a test lamp.
C3 XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 335
CLUTCH
GEARBOX
TRANSMISSION
Engines: KFV NFU RFN RHZ
Updating the value of the oil usage counter.
Using PROXIA.
Access to reading and recording of the oil counter is via the menu:
«Configuration
(integrated circuit button)/ Oil counter».
Adjustment of the oil counter value is done in incremental steps of
2750units.
Using LEXIA or ELIT.Access to reading and recording of the oil counter is via the menu:
«Oil counter».
Adjustment of the oil counter value is done by entering directly the
5 figures of the oil counter.
Downloading.
ECU downloading procedure:
Follow the diagnostic tool procedure.
A new ECU or downloaded update is always configured with the
following options:
SHIFT LOCK gear selection lever position.
Without OBD outlet
(depollution L4).
If the ECU is to be fitted to a vehicle with depollution
L4or not
equipped with gear lever locking safety: Perform a configuration operation.
Pedal initialisation.
A pedal initialisation must be carried out in the following cases:
Replacement of the automatic gearbox ECU.
Replacement of the automatic gearbox.
Downloading of the ECU configuration.
Adjustment or replacement of the accelerator cable.
Replacement of the butterfly potentiometer.
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOXC3 XSARA XSARA PICASSO
Procedure for initialising the automatic gearbox ECU

Downloaded from www.Manualslib.com manuals search engine 340
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
In passenger compartment.The gear selector is guided by the shape of the stepped gate and by a retaining spring which
pulls it to the left hand side.
The gear selector control has
5 positions:
Position
«P»: Park (locking and immobilisation of the vehicle).
Position «R»:Reverse gear.
Position «N»: Neutral.
Position «D»: Drive (use of the 4 gears in their autoadaptive automatic function).
Position «M»: Manual (this position lets the driver select his own gears in sequential mode
by pulling the gear selector to «M-»or pushing it to «M+»).
NOTE:Only the positions «P»or «N»authorise the starting of the engine.
In position
«M», selection is by an electronic sensor located close to the gear lever.
The variation of flux necessary to the movement of the sensor cells is obtained by a magnet
located on the lever itself. This enables the change of status.
Engines: KFV RFN
C3 XSARA PICASSO
B2CP3H7DB2CP3MUD
XSARA PICASSOC3

Downloaded from www.Manualslib.com manuals search engine 342
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Gearbox end.
The automatic gearbox is controlled by a cable.
«c»or «d»Pushbutton.
(1)Control lever with balljoint.
(2)Automatic adjustment (pull out the button to adjust the control, push it in to lock the
adjustment of the control).
(3)Sleeve stop.
(4)Selection control locking clip (5)on the sleeve stop(3).
Engines: KFV RFN
C3 XSARA PICASSO
B2CP3H8CB2CP3N7C
XSARA PICASSOC3

Downloaded from www.Manualslib.com manuals search engine 345
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
NOTE:The «shift lock»«P».
Unlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed.
Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch. Automatic gearbox ECU.
Electrical harnesses.
Battery voltage.
Remove:
The gear lever knob
(1)(pull upwards).
The cover (2)(Unclip).
The top of the central console (3).
Unlock the «shift lock» (4)with the aid of a screwdriver.
Move the gear selection lever out of position «P».
Engine: KFV
C3
C5FP0ETCB2CP3GZC

Downloaded from www.Manualslib.com manuals search engine 346
CLUTCH
GEARBOX
TRANSMISSION
XSARAAL4 AUTOMATIC GEARBOX
Engines: NFU RFN RHZ
SHIFT LOCK.
NOTE:
The «shift lock»«P».
U
nlocking the «SHIFT LOCK»(normal operation).
Switch on the ignition.
Press the brake pedal and keep it pressed. Move the gear selection lever out of position
«P».
Unlocking the «SHIFT LOCK»(with an operating fault).NOTE:It is impossible to unlock the «shift lock»
«Shift lock».
Gear lever position switch.
Automatic gearbox ECU.
Electrical harnesses. Battery voltage.
Remove:
The cover
(1).
Unlock the «shift lock» (2) with the aid of a screwdriver.
Move the gear selection lever out of position «P».
C5FP06ZC
C5FP06YC