2004 Citroen BERLINGO pluriel

Downloaded from www.Manualslib.com manuals search engine 108
ENGINECYLINDER HEAD
Engines: 8HX 8HW 8HZ 8HV 8HY
Cylinder head tightening (m.daN) One Cylinder head bolts
X =MAX.reusable length
Pretightening: 2 ± 0,2 m.daN
Tightening: 4 ± 0,4 m.daN
Angular tightening: 230° ± 5°
The bolts should have been tho
roughly cleaned and dried with a
dry metal brush.
Oil the threads and under the
heads of the bolts
(use engine oil
or Molykote G Rapid Plus).
Pass a tap into the holes in the
cylinder block.
8HX 8HW 8HZ 8HV 8HY
8HX 8HW 8HZ 8HV 8HY
X = 149 mm
B1DP1CLC
B1DP1DBC
NOTE:Retightening of the cylinder head
after a completed repair is prohibited.
The cylinder head gasket is dryfitted.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 115
ENGINE
115
PETROL
A UXILIARY EQUIPMENT DRIVE BELT
TU
1
JP
3
JP +
J47
J410
J4RS ET EW
Engine type
C2
C3
C3 Pluriel
XSARA
See pages:
See pages:
See pages:
See pages:
HFX KFV KFW KFU NFV NFU 6FZ RFN RFS
1.1i 1.4i 1.6i 16V
118 to 119118 to 119
1.1i 1.4i 1.4i 16V 1.6i 16V
118 to 119 123 to 124 118 to 119
1.4i1.6i 16V
118 to 119 118 to 119
1.4i 1.6i 16V 2.0i 16V 2.0i 16V
122 125 128 126 to 127
1.6i1.8i 16V 2.0i 16V
120 to 121 128
TUXU
35
JP4
XSARA
Picasso
See pages:

Downloaded from www.Manualslib.com manuals search engine 116
ENGINEDIESEL AUXILIARY EQUIPMENT DRIVE BELT
DV
TD
4
TED48
B10
ATED
Engine type
C2
C3
C3 Pluriel
XSARA
See pages:
See pages:
See pages:
See pages:
8HX 8HW 8HZ 8HV 8HY 9HZ 9HY WJY RHY RHZ
1.4 HDi
135 to 136
1.4 HDi 1.4 HDi 1.4 HDi 16V 1.4 HDi 16V
135 to 136 139
1.4 HDi
135 to 136
1.4 HDi 1.9 D 2.0 HDi 2.0 HDi
137 to 138 129 to 134 141 to 144
1.6 HDi 16V1.6 HDi 16V 2.0 HDi
140 141 to 144
DW
6
XSARA
Picasso
See pages:
TD

Downloaded from www.Manualslib.com manuals search engine 118
ENGINE
B1BP2LSCB1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: HFX KFV NFU
Tools.
[1]
Pliers for removing plastic pegs: 7504 –T
[2] Belt tension measuring instrument: 4122T
V
ehicle without air conditioning.
Refit.
Refit the belt.
Respect the following sequence:
Crankshaft pinion.
Alternator pulley.Place tool
[2]on the belt.
Tighten screw (1)to achieve a tension of:55 ± 3 SEEM units.Tighten:
Screw (3).
Screw (2).
Remove tool [2]and complete the refitting.
Remove.
Slacken:
Screw
(2). Screw (3). Tensioning screw (1).
Push the alternator back towards the engine.
Remove the belt.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 119
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines: HFX KFV NFU
B1BP10XC
Vehicle with air conditioning.
Remove
Slacken:
Screws (6), (4)and (5).
Fully detension the belt by acting on the tensioner roller.
Remove the accessories drive belt.
Refit.Respect the following sequence:
Crankshaft pinion.
Aircon compressor pulley.
Guide roller.
Alternator pulley.
Tensioner roller.Place tool
[2]on the belt.
Tighten screw (5)to achieve a belt tension of:120 ± 3 SEEM units. Tighten screws (4)and (6) Remove tool [2].
Complete the refitting.
B1BP10VC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 135
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HX 8HW
With compressor and alternator .
B1BP2MKCB1BP2MJD
Tools.
[1]
Pliers for removing plastic pegs: 7504T
[2]Tensioner roller compression lever:().0194.E
[3]Tensioner roller setting peg Ø4 mm: ().0194.F
Removing.
Disconnect the battery negative cable.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel.
Move aside the splashshield, using tool
[1].
IMPERATIVE: In the case of belt reuse, mark the
direction of rotation of the belt. If the index on the
tensioner roller is outside the marks, change
the auxiliary equipment drive belt.
The alternator (1).
The aircon compressor (2).
Detension the auxiliary belt tensioner roller, using tool [2].
Position the peg [3].
Remove the auxiliary drive belt.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 136
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HX 8HW
Markings on the dynamic tensioner roller.
«a»
Position of «maximum wear» of the auxiliary drive belt.«b»Normal position.
Refitting.
NOTE:
Check that the tensioner roller moves freely (no tight spot). If this is not the
case, replace the tensioner roller.
Respect the direction of fitting of the drive belt.
Complete the setting of the belt, of both sides, by means of the tensioner roller.
Make sure that the drive belt is correctly positioned in the
«V»grooves of the
various pulleys.
Move the tool
[2]on the tensioner roller to remove the peg [3].
B1EP18UD
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine ENGINE
PETROL
CHECKING AND SETTING THE VALVE TIMING
TU
1
JP
3
JP +
J47
J410
J4RS ET EW
Engine type
C2
C3
C3 Pluriel
XSARA
See pages:
See pages:
See pages:
See pages:
HFX KFV KFW KFU NFV NFU 6FZ RFN RFS
1.1i 1.4i 1.6i 16V
148 to 157148 to 157
1.1i 1.4i 1.4i 16V 1.6i 16V
148 to 157 165 to 170 148 to 157
1.4i1.6i 16V
148 to 157 148 to 157
1.4i 1.6i 16V 2.0i 16V 2.0i 16V
148 to 157 161 to 164 171 to 178 179 to 183
1.6i1.8i 16V 2.0i 16V
158 to 160 171 to 178
TUXU
35
JP4
XSARA
Picasso
See pages:
145