2004 CHRYSLER VOYAGER hood open

material on the condenser fins that might obstruct
air flow. Also, any factory-installed air seals or
shrouds must be properly reinstalled following radia-
tor or condenser service.
The A/C condenser cannot be repaired or adjusted,
and if faulty or damaged, it must be replaced.
REMOVAL
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
FRONT - WARNING - A/C PLUMBING) and (Refer to
24 - HEATING & AIR CONDITIONING/PLUMBING -
FRONT - CAUTION - A/C PLUMBING).
NOTE: Before removing the condenser, note the
location of each of the radiator and condenser air
seals. These air seals are used to direct air through
the condenser and radiator. The air seals must be
reinstalled in their proper locations in order for the
air conditioning and engine cooling systems to per-
form as designed.
(1) Recover the refrigerant from the refrigerant
system (Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING - FRONT/REFRIGERANT - STAN-
DARD PROCEDURE - REFRIGERANT
RECOVERY).
(2) Remove the two large screws that secure the
front fascia and the outboard ends of the radiator
sight shield to the radiator closure panel crossmem-
ber (Fig. 8).(3) Remove the five small screws that secure the
front fascia grille inserts to the radiator sight shield.
(4) Remove the radiator sight shield from the radi-
ator closure panel crossmember.
(5) Remove the two screws that secure the hood
latch unit to the front of the radiator closure panel
crossmember and move the latch out of the way over
the top of the crossmember. Mark the location of
latch for reinstallation.
(6) Disconnect the hoses from the transmission oil
cooler fittings on the left side of the cooling module
(Refer to 7 - COOLING/TRANSMISSION/TRANS
COOLER LINES - REMOVAL).
(7) Remove the nut that secures the discharge line
fitting to the A/C condenser on the right side of the
cooling module.
(8) Disconnect the discharge line fitting from the
condenser inlet port.
(9) Remove the O-ring seal and gasket from the
discharge line fitting and discard.
(10) Install plugs in, or tape over the opened dis-
charge line fitting and the condenser inlet port.
(11) Remove the nut that secures the liquid line
fitting to the condenser on the right side of the cool-
ing module.
(12) Disconnect the liquid line fitting from the con-
denser outlet port.
(13) Remove the O-ring seal and gasket from the
liquid line fitting and discard.
(14) Install plugs in, or tape over the opened liquid
line fitting and the condenser outlet port.
(15) Remove the screw that secures the top of the
mounting bracket on each side of the condenser to
the cooling module (Fig. 9).
(16) Lift the condenser, transmission oil cooler, and
mounting brackets as a unit far enough to disengage
the locating pin that secures the mounting brackets
in the lower mount rubber isolators on each side of
the cooling module.
(17) Remove the condenser, transmission oil cooler,
and mounting brackets from the vehicle as a unit.
(18) Remove the two screws that secure each
mounting bracket to the sides of the A/C condenser.
(19) Remove the one screw that secures the left
mounting bracket to the side of the transmission oil
cooler.
(20) Remove the left mounting bracket from the
side of the condenser and transmission oil cooler.
(21) Remove the condenser from the right mount-
ing bracket and transmission oil cooler unit.
Fig. 8 Radiator Air Seals
1 - LARGE SCREWS (2)
2 - SMALL SCREWS (5)
3 - RADIATOR SIGHT SHIELD
4 - GRILLE INSERTS
5 - FRONT FASCIA
RSPLUMBING - FRONT24-77
A/C CONDENSER (Continued)

STANDARD PROCEDURE - REFRIGERANT OIL
LEVEL
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
FRONT - WARNING - A/C PLUMBING) and (Refer to
24 - HEATING & AIR CONDITIONING/PLUMBING -
FRONT - CAUTION - A/C PLUMBING).
CAUTION: Use only PAG oils that are designed to
work with R-134a refrigerant and the A/C compres-
sor in the vehicle. Refer to the underhood A/C Sys-
tem Specification Label.
It is important to have the correct amount of lubri-
cant in the A/C refrigerant system to ensure proper
lubrication of the A/C compressor. Too little lubricant
will result in damage to the compressor. Too much
lubricant will reduce the cooling capacity of the A/C
system and consequently result in higher discharge
air temperatures.
The lubricant used in the compressor is polyalka-
lene glycol PAG lubricant. Only the refrigerant lubri-
cant approved for use with this vehicle should be
used to service the system. Do not use any other
lubricant. The lubricant container should be kept
tightly capped until it is ready for use. Refrigerant
lubricant will quickly absorb any moisture it comes
in contact with.
It will not be necessary to check the oil level in the
A/C compressor or to add oil, unless there has been
an oil loss. An oil loss may occur due to a rupture or
leak from a refrigerant line, connector fitting, compo-
nent or component seal. If a leak occurs, add 30 mil-
liliters (1 fluid ounce) of the recommended
refrigerant oil to the refrigerant system after the
repair has been made. Refrigerant oil loss will be evi-
dent at the leak point by the presence of a wet, shiny
surface around the leak.
REFRIGERANT OIL LEVEL CHECK
When an air conditioning system is first assembled
at the factory, all components (except the A/C com-
pressor) are refrigerant oil free. After the refrigerant
system has been charged with (R-134a) refrigerant
and operated, the oil in the A/C compressor is dis-
persed through the lines and components. The A/C
evaporator, A/C condenser, and receiver/drier will
retain a significant amount of oil. Refer to the A/C
Component Refrigerant Oil Capacities table. When a
component is replaced, the specified amount of refrig-
erant oil must be added. When the compressor is
replaced, the amount of oil that is retained in the
rest of the system must be drained from the replace-ment A/C compressor. The oil capacity of the system,
minus the amount of oil still in the remaining com-
ponents (refer to the oil capacity chart below) can be
measured and poured into the suction port of the A/C
compressor. When a line or component has ruptured
and oil has escaped, the receiver/drier must be
replaced along with the ruptured component.
Example: On an A/C system the A/C evaporator
retains 60 ml. (2 oz.). The A/C condenser retains 30
ml. (1 oz.) of oil, and system capacity may be 150 ml.
(5.00 oz.) of oil.
150 ml. minus 90 ml. equals 60 ml. (2.00 oz.).
A/C COMPONENT REFRIGERANT OIL
CAPACITIES
Front A/C Front & Rear
A/C
COMPONENT ml fl oz ml fl oz
Total System Fill 180 6.1 300 10.14
Receiver/Drier 25 0.9 25 0.9
A/C Condenser 50 1.8 50 1.8
Front Evaporator 50 1.8 50 1.8
Rear Evap. (including
underbody lines)N/A N/A 50 1.8
A/C Compressor Drain and measure the oil
from the old compressor -
See text above.
VERIFY REFRIGERANT LUBRICANT LEVEL
(1) Recover the refrigerant from the system.
(2) Disconnect the refrigerant lines from the A/C
compressor. Cap open lines to prevent moisture from
entering the system.
(3) Remove A/C compressor from the vehicle.
(4) From the suction and discharge ports on the
A/C compressor, drain the lubricant from the com-
pressor.
(5) Add the system capacity minus the capacity of
the components that have not been replaced. Refer to
the A/C Component Refrigerant Oil Capacities chart.
Add lubricant through the suction and discharge
ports on the A/C compressor.
(6) Install the A/C compressor and connect the
refrigerant lines. Then evacuate and charge refriger-
ant system.
(7) Most reclaim/recycling equipment will measure
the lubricant being removed. This amount of lubri-
cant should be added back to the system. If a new
A/C compressor is being installed, drain the lubricant
from the used compressor, measure the amount
drained and discard the used lubricant. Drain the
lubricant from the new A/C compressor into a clean
container. Return the amount of lubricant measured
from the used compressor, plus the amount reclaimed
RSPLUMBING - FRONT24-93
REFRIGERANT OIL (Continued)

HEATED SEAT SWITCH - INSTALLATION,
DRIVER............................8G-10
HEATED SEAT SWITCH - INSTALLATION,
PASSENGER........................8G-14
HEATED SEAT SWITCH - OPERATION,
DRIVER.............................8G-8
HEATED SEAT SWITCH - OPERATION,
PASSENGER........................8G-12
HEATED SEAT SWITCH - REMOVAL,
DRIVER............................8G-10
HEATED SEAT SWITCH - REMOVAL,
PASSENGER........................8G-14
HEATED SEAT SYSTEM - DESCRIPTION....8G-7
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SYSTEM - OPERATION.....8G-8
HEATER - DESCRIPTION, CABIN........24-112
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-20
HEATER - DIAGNOSIS AND TESTING,
DIESEL SUPPLEMENTAL CABIN........24-113
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-20
HEATER - OPERATION, ENGINE BLOCK....7-20
HEATER - REMOVAL, ENGINE BLOCK......7-20
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-4
HEATER CONTROL - DESCRIPTION, A/C . . . 24-20
HEATER CONTROL - INSTALLATION, A/C . . 24-21
HEATER CONTROL - REMOVAL, A/C.......24-21
HEATER CORE - DESCRIPTION....24-101,24-83
HEATER CORE - INSTALLATION . . . 24-103,24-85
HEATER CORE - OPERATION......24-101,24-83
HEATER CORE - REMOVAL.......24-102,24-84
HEATER CORE FILLING - STANDARD
PROCEDURE, REAR..................24-101
HEATER CORE TUBES - INSTALLATION . . . 24-85
HEATER CORE TUBES - REMOVAL.......24-83
HEATER HOSES - INSTALLATION.......24-104
HEATER HOSES - REMOVAL...........24-103
HEATER INLET HOSE - INSTALLATION....24-86
HEATER INLET HOSE - REMOVAL........24-85
HEATER LINES - INSTALLATION, REAR . . 24-111
HEATER PERFORMANCE TEST -
DIAGNOSIS AND TESTING.............24-10
HEATER RETURN HOSE - INSTALLATION . . 24-87
HEATER RETURN HOSE - REMOVAL......24-86
HEATER TESTING - DIAGNOSIS AND
TESTING, ENGINE BLOCK...............7-20
HEATER TUBES - REMOVAL,
UNDERBODY.......................24-109
HEATER UNIT - INSTALLATION.........24-119
HEATER UNIT - REMOVAL.............24-118
HEATER WIRING - INSTALLATION,
SUPPLEMENTAL DIESEL..............24-119
HEATER WIRING - REMOVAL,
SUPPLEMENTAL DIESEL..............24-119
HEAVY DUTY, CARGO - INSTALLATION,
AWD ...............................2-36
HEAVY DUTY, CARGO - REMOVAL, AWD . . . 2-36
HEIGHT ADJUSTER-BORC-PILLAR -
INSTALLATION, SEAT BELT.............8O-13
HEIGHT ADJUSTER-BORC-PILLAR -
REMOVAL, SEAT BELT................8O-13
HEIGHT ADJUSTER KNOB -
INSTALLATION, SEAT BELT.............8O-14
HEIGHT ADJUSTER KNOB - REMOVAL,
SEAT BELT .........................8O-14
HEIGHT MEASUREMENT - STANDARD
PROCEDURE, CURB...................2-55
HIGH AND LOW LIMITS - DESCRIPTION . . . 25-8
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION
.......................24-73
HIGH PRESSURE RELIEF VALVE -
OPERATION
.........................24-73
HIGH SPEED OPERATION - STANDARD
PROCEDURE, TIRE PRESSURE
.....22-17,22s-9
HINGE - INSTALLATION
......23-18,23-40,23-60
HINGE - INSTALLATION, CENTER
........23-24HINGE - INSTALLATION, LOWER........23-28
HINGE - INSTALLATION, UPPER.........23-36
HINGE - REMOVAL.........23-17,23-40,23-60
HINGE - REMOVAL, BENCH SEAT BACK . . 23-102
HINGE - REMOVAL, CENTER............23-24
HINGE - REMOVAL, LOWER............23-28
HINGE - REMOVAL, UPPER.............23-36
HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - INSTALLATION, SEAT
BACK.............................23-101
HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - REMOVAL, SEAT BACK . . 23-101
HOISTING - STANDARD PROCEDURE......0-27
HOLD OPEN LATCH - INSTALLATION.....23-25
HOLD OPEN LATCH - REMOVAL.........23-25
HOLD OPEN LATCH CABLE -
INSTALLATION.......................23-38
HOLD OPEN LATCH CABLE - REMOVAL . . . 23-38
HOLD OPEN LATCH STRIKER -
INSTALLATION.......................23-26
HOLD OPEN LATCH STRIKER -
REMOVAL..........................23-26
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-15
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-16
HOLDDOWN - OPERATION, BATTERY.....8F-15
HOLDDOWN - REMOVAL, BATTERY . 8F-15,8F-16
HOLDER - INSTALLATION, CUP.........23-64
HOLDER - REMOVAL, CUP.............23-64
HOLDING CLUTCHES - DESCRIPTION . . . 21-207,
21s-106
HOLDING CLUTCHES - OPERATION.....21-207,
21s-106
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-5
HONING - STANDARD PROCEDURE,
CYLINDER BORE.................9-112,9-35
HOOD - INSTALLATION................23-61
HOOD - REMOVAL....................23-60
HOOD AJAR SWITCH - EXPORT -
INSTALLATION.......................8Q-3
HOOD AJAR SWITCH - EXPORT -
REMOVAL...........................8Q-3
HORN - DIAGNOSIS AND TESTING.......8H-3
HORN - INSTALLATION.................8H-5
HORN - REMOVAL....................8H-4
HORN CHIRP PREFERENCE - STANDARD
PROCEDURE....................8N-42,8N-5
HORN SWITCH - DESCRIPTION..........8H-5
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - INSTALLATION, HEATER INLET....24-86
HOSE - INSTALLATION, HEATER RETURN . 24-87
HOSE - REMOVAL, HEATER INLET.......24-85
HOSE - REMOVAL, HEATER RETURN.....24-86
HOSE CLAMPS - DESCRIPTION...........7-1
HOSE CLAMPS - OPERATION.............7-2
HOSES - DESCRIPTION, BRAKE TUBES....5-14,
5s-13
HOSES - INSPECTION, BRAKE TUBES.....5-14,
5s-13
HOSES - INSTALLATION, HEATER.......24-104
HOSES - INSTALLATION, WASHER.......8R-13
HOSES - OPERATION, BRAKE TUBES . 5-14,5s-13
HOSES - REMOVAL, HEATER..........24-103
HOSES - REMOVAL, WASHER..........8R-13
HOSES AND CLAMP - STANDARD
PROCEDURE.........................14-7
HOUSING - INSTALLATION, AIR
CLEANER........................9-24,9-99
HOUSING - INSTALLATION, HVAC........24-61
HOUSING - INSTALLATION, LOCK
CYLINDER..........................19-19
HOUSING - REMOVAL, AIR CLEANER . . 9-24,9-99
HOUSING - REMOVAL, HVAC...........24-60
HOUSING - REMOVAL, LOCK CYLINDER . . 19-17
HOUSING FLUID CHANGE - STANDARD
PROCEDURE, OVERRUNNING CLUTCH.....3-41
HOUSING FLUID LEAKAGE - DIAGNOSIS
AND TESTING, TORQUE CONVERTER . . . 21-123,
21s-31
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION
.....................8W-01-1
HUB / BEARING - DESCRIPTION
.......2-30,2-4
HUB / BEARING - INSTALLATION
......2-33,2-6
HUB / BEARING - OPERATION
........2-30,2-4
HUB / BEARING - REMOVAL
..........2-31,2-5HUB AND BEARING - DIAGNOSIS AND
TESTING.........................2-31,2-5
HVAC - LWB - INSTALLATION, SEAT
BELT & RETRACTOR - SECOND ROW -
RIGHT OUTBOARD WITH REAR.........8O-16
HVAC - LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR...............8O-16
HVAC HOUSING - INSTALLATION........24-61
HVAC HOUSING - REMOVAL............24-60
HVAC LOUVER - INSTALLATION, REAR . . . 23-81
HVAC LOUVER - REMOVAL, REAR.......23-81
HYDRAULIC CIRCUITS AND VALVES -
OPERATION..........................5-83
HYDRAULIC LASH ADJUSTER NOISE
DIAGNOSIS - DIAGNOSIS AND
TESTING............................9-34
HYDRAULIC LASH ADJUSTERS -
INSTALLATION........................9-34
HYDRAULIC LASH ADJUSTERS -
REMOVAL...........................9-34
HYDRAULIC LIFTERS - DIAGNOSIS AND
TESTING...........................9-113
HYDRAULIC LIFTERS (CAM IN BLOCK) -
DESCRIPTION.......................9-113
HYDRAULIC LIFTERS (CAM IN BLOCK) -
INSTALLATION.......................9-114
HYDRAULIC LIFTERS (CAM IN BLOCK) -
REMOVAL..........................9-114
HYDRAULIC PRESSURE TESTS -
DIAGNOSIS AND TESTING.......21-120,21s-28
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS - 41TE TRANSAXLE....21-169
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS - 4XTE TRANSAXLE....21s-75
HYDROSTATIC LOCKED ENGINE -
STANDARD PROCEDURE............9-10,9-85
ICU - ASSEMBLY......................5-94
ICU - DISASSEMBLY...................5-93
ICU (INTEGRATED CONTROL UNIT) -
DESCRIPTION........................5-89
ICU (INTEGRATED CONTROL UNIT) -
OPERATION..........................5-90
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-2
IDENTIFICATION - DESCRIPTION,
VEHICLE............................23-1
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION, DIAGNOSIS AND
TESTING - SEAL......................21-3
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-9
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-28
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-29
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-28
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-29
IGNITION COIL - DESCRIPTION...........8I-6
IGNITION COIL - OPERATION.............8I-7
IGNITION INTERLOCK - DESCRIPTION....19-17
IGNITION SENSE - PCM INPUT -
OPERATION.........................8E-15
IGNITION SWITCH - INSTALLATION......19-16
IGNITION SWITCH - REMOVAL..........19-14
IGNITION SYSTEM - DESCRIPTION........8I-1
IGNITION SYSTEM - OPERATION..........8I-1
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-13
IIITSTATE DISPLAY TEST MODE,
OPERATION - DRB....................25-9
ILLUMINATION LAMPS - INSTALLATION,
CLUSTER...........................8L-21
ILLUMINATION LAMPS - REMOVAL,
CLUSTER...........................8L-21
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY
........................8E-18
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY
........................8E-19
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY
........................8E-18
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY
........................8E-18
INBOARD - 50/50 BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW
.......................8O-13
RSINDEX17
Description Group-Page Description Group-Page Description Group-Page

STRIKER - REMOVAL, LATCH . 23-19,23-41,23-62
STRIKER - REMOVAL, REAR LATCH......23-29
STRIPPED THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD..............9-145
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS....................23-156
STRUCTURAL COLLAR - INSTALLATION....9-48
STRUCTURAL COLLAR - REMOVAL.......9-47
STRUT ASSEMBLY - ASSEMBLY..........2-23
STRUT ASSEMBLY - DESCRIPTION.......2-19
STRUT ASSEMBLY - DIAGNOSIS AND
TESTING............................2-20
STRUT ASSEMBLY - DISASSEMBLY.......2-21
STRUT ASSEMBLY - INSTALLATION.......2-25
STRUT ASSEMBLY - OPERATION.........2-20
STRUT ASSEMBLY - REMOVAL...........2-21
STUDS - FRONT - INSTALLATION,
WHEEL MOUNTING...................22-21
STUDS - FRONT - REMOVAL, WHEEL
MOUNTING.........................22-20
STUDS - REAR - INSTALLATION, WHEEL
MOUNTING.........................22-22
STUDS - REAR - REMOVAL, WHEEL
MOUNTING.........................22-21
SUCTION LINE - INSTALLATION . . . 24-107,24-95
SUCTION LINE - REMOVAL.......24-106,24-94
SUN VISOR - INSTALLATION...........23-82
SUN VISOR - REMOVAL...............23-82
SUN VISOR SUPPORT - INSTALLATION.....23-83
SUN VISOR SUPPORT - REMOVAL.......23-83
SUNROOF - DESCRIPTION............23-116
SUNROOF - DIAGNOSIS AND TESTING . . . 23-116
SUNROOF ASSEMBLY - INSTALLATION . . 23-120
SUNROOF ASSEMBLY - REMOVAL......23-120
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-120
SUNROOF MOTOR - INSTALLATION.....23-121
SUNROOF MOTOR - REMOVAL.........23-121
SUNROOF SWITCH - INSTALLATION.....23-123
SUNROOF SWITCH - REMOVAL........23-123
SUNSHADE - INSTALLATION...........23-121
SUNSHADE - REMOVAL..............23-120
SUPPLEMENTAL CABIN HEATER -
DIAGNOSIS AND TESTING, DIESEL......24-113
SUPPLEMENTAL DIESEL HEATER
WIRING - INSTALLATION.............24-119
SUPPLEMENTAL DIESEL HEATER
WIRING - REMOVAL.................24-119
SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT ..............................8E-15
SUPPLY - PCM OUTPUT - SBEC
CONTROLLER - OPERATION, 8-VOLT.....8E-15
SUPPORT - INSTALLATION, LUMBAR....23-106
SUPPORT - INSTALLATION, SUN VISOR . . . 23-83
SUPPORT - REMOVAL, LUMBAR.......23-106
SUPPORT - REMOVAL, SUN VISOR......23-83
SUPPORT CYLINDER - INSTALLATION....23-43
SUPPORT CYLINDER - REMOVAL........23-43
SUPPORT PLATE - DRUM BRAKE -
INSTALLATION...................5-56,5s-58
SUPPORT PLATE - DRUM BRAKE -
REMOVAL......................5-56,5s-58
SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO NOISE...........8A-11
SUPPRESSION COMPONENTS -
OPERATION, RADIO NOISE.............8A-12
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET.......9-11,9-85
SUSPENSION - DESCRIPTION, FRONT......2-2
SUSPENSION - DESCRIPTION, REAR
......2-27
SUSPENSION - OPERATION, FRONT
........2-2
SUSPENSION - OPERATION, REAR
........2-28
SUSPENSION AND STEERING -
DIAGNOSIS AND TESTING
..............2-50
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - FRONT
................2-3
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - REAR
................2-28
SUSPENSION, SPECIAL TOOLS - FRONT
....2-3
SUSPENSION, SPECIAL TOOLS - REAR
....2-28
SWITCH - DESCRIPTION
................8P-6
SWITCH - DESCRIPTION, AUTOSTICK
. . . 21-189
SWITCH - DESCRIPTION, BRAKE FLUID
LEVEL
..........................5-10,5s-9
SWITCH - DESCRIPTION, BRAKE LAMP
....8L-4
SWITCH - DESCRIPTION, DOOR
CYLINDER LOCK
.....................8N-40SWITCH - DESCRIPTION, DRIVER
HEATED SEAT ........................8G-8
SWITCH - DESCRIPTION, DRIVER SEAT . . 8N-10,
8N-53
SWITCH - DESCRIPTION, EXTERIOR
HANDLE...........................8N-11
SWITCH - DESCRIPTION, FULL OPEN....8N-12,
8N-31
SWITCH - DESCRIPTION, HORN..........8H-5
SWITCH - DESCRIPTION, LEFT B-PILLAR . 8N-32
SWITCH - DESCRIPTION, MEMORY SET . . 8N-12,
8N-55
SWITCH - DESCRIPTION, OIL PRESSURE . 9-141
SWITCH - DESCRIPTION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - DESCRIPTION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - DESCRIPTION, REAR
WINDOW DEFOGGER..................8G-4
SWITCH - DESCRIPTION, REAR
WIPER/WASHER.....................8R-11
SWITCH - DESCRIPTION, RIGHT
B-PILLAR..........................8N-32
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP........................8L-4
SWITCH - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK...............8N-40
SWITCH - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
SWITCH - DIAGNOSIS AND TESTING,
DRIVER HEATED SEAT.................8G-9
SWITCH - DIAGNOSIS AND TESTING,
DRIVER SEAT...................8N-11,8N-54
SWITCH - DIAGNOSIS AND TESTING,
FAILED PARK........................8R-2
SWITCH - DIAGNOSIS AND TESTING,
FRONT WIPER/WASHER................8R-2
SWITCH - DIAGNOSIS AND TESTING,
HEADLAMP.........................8L-12
SWITCH - DIAGNOSIS AND TESTING,
MEMORY.....................8N-13,8N-56
SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-18
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER HEATED SEAT.............8G-13
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER SEAT..............8N-14,8N-57
SWITCH - DIAGNOSIS AND TESTING,
REMOTE...........................8N-49
SWITCH - DIAGNOSIS AND TESTING,
TRACTION CONTROL...................5-82
SWITCH - DIAGNOSIS AND TESTING,
WINDOW...........................8N-64
SWITCH - EXPORT - DESCRIPTION,
DOOR CYLINDER LOCK................8N-3
SWITCH - EXPORT - DESCRIPTION,
POWER FOLDAWAY MIRROR...........8N-48
SWITCH - EXPORT - DIAGNOSIS AND
TESTING, DOOR CYLINDER LOCK........8N-3
SWITCH - EXPORT - INSTALLATION,
DOOR CYLINDER LOCK................8N-4
SWITCH - EXPORT - INSTALLATION,
HOOD AJAR.........................8Q-3
SWITCH - EXPORT - INSTALLATION,
POWER FOLDAWAY MIRROR
...........8N-49
SWITCH - EXPORT - OPERATION, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - OPERATION,
POWER FOLDAWAY MIRROR
...........8N-48
SWITCH - EXPORT - REMOVAL, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - REMOVAL, HOOD
AJAR
...............................8Q-3
SWITCH - EXPORT - REMOVAL, POWER
FOLDAWAY MIRROR
..................8N-48
SWITCH - INSTALLATION
...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE
PEDALS
............................5s-10
SWITCH - INSTALLATION, BACK-UP
LAMP
..............................21-62
SWITCH - INSTALLATION, BRAKE FLUID
LEVEL
.........................5-11,5s-10
SWITCH - INSTALLATION, BRAKE LAMP
. . . 8L-5
SWITCH - INSTALLATION, CENTER
CONSOLE LAMP
.....................8L-21
SWITCH - INSTALLATION, CLUTCH
PEDAL INTERLOCK
....................6-14SWITCH - INSTALLATION, CLUTCH
PEDAL UPSTOP.......................6-16
SWITCH - INSTALLATION, DOOR
CYLINDER LOCK.....................8N-41
SWITCH - INSTALLATION, DOOR LOCK....8N-4,
8N-42
SWITCH - INSTALLATION, DRIVER
HEATED SEAT .......................8G-10
SWITCH - INSTALLATION, DRIVER SEAT . . 8N-12,
8N-55
SWITCH - INSTALLATION, EXTERIOR
HANDLE...........................8N-12
SWITCH - INSTALLATION, FULL OPEN....8N-13
SWITCH - INSTALLATION, GLOVE BOX
LAMP..............................8L-22
SWITCH - INSTALLATION, HEADLAMP....8L-13
SWITCH - INSTALLATION, IGNITION......19-16
SWITCH - INSTALLATION, LEFT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, MEMORY SET . 8N-13,
8N-56
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-18
SWITCH - INSTALLATION, OIL
PRESSURE.....................9-141,9-54
SWITCH - INSTALLATION, PASSENGER
HEATED SEAT .......................8G-14
SWITCH - INSTALLATION, PASSENGER
SEAT.........................8N-15,8N-57
SWITCH - INSTALLATION, REMOTE......8N-49
SWITCH - INSTALLATION, RIGHT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, SUNROOF....23-123
SWITCH - INSTALLATION, WASHER
FLUID LEVEL........................8R-12
SWITCH - INSTALLATION, WINDOW.....8N-65
SWITCH - OPERATION.................8P-6
SWITCH - OPERATION, AUTOSTICK.....21-189
SWITCH - OPERATION, BRAKE FLUID
LEVEL..........................5-10,5s-9
SWITCH - OPERATION, BRAKE LAMP......8L-4
SWITCH - OPERATION, DOOR CYLINDER
LOCK..............................8N-40
SWITCH - OPERATION, DRIVER HEATED
SEAT ...............................8G-8
SWITCH - OPERATION, DRIVER SEAT....8N-11,
8N-54
SWITCH - OPERATION, EXTERIOR
HANDLE...........................8N-11
SWITCH - OPERATION, FULL OPEN . 8N-12,8N-31
SWITCH - OPERATION, LEFT B-PILLAR . . . 8N-32
SWITCH - OPERATION, MEMORY SET . . . 8N-13,
8N-56
SWITCH - OPERATION, OIL PRESSURE . . . 9-141
SWITCH - OPERATION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - OPERATION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - OPERATION, REAR WINDOW
DEFOGGER..........................8G-4
SWITCH - OPERATION, REAR WIPER/
WASHER...........................8R-11
SWITCH - OPERATION, RIGHT B-PILLAR . . 8N-32
SWITCH - REMOVAL...................8P-6
SWITCH - REMOVAL, ADJUSTABLE
PEDALS............................5s-10
SWITCH - REMOVAL, BACK-UP LAMP....21-62
SWITCH - REMOVAL, BRAKE FLUID
LEVEL.........................5-11,5s-10
SWITCH - REMOVAL, BRAKE LAMP.......8L-5
SWITCH - REMOVAL, CENTER CONSOLE
LAMP..............................8L-21
SWITCH - REMOVAL, CLUTCH PEDAL
INTERLOCK..........................6-13
SWITCH - REMOVAL, CLUTCH PEDAL
UPSTOP.............................6-15
SWITCH - REMOVAL, DOOR CYLINDER
LOCK..............................8N-41
SWITCH - REMOVAL, DOOR LOCK . . 8N-4,8N-42
SWITCH - REMOVAL, DRIVER HEATED
SEAT ..............................8G-10
SWITCH - REMOVAL, DRIVER SEAT.....8N-12,
8N-55
SWITCH - REMOVAL, EXTERIOR HANDLE
. 8N-11
SWITCH - REMOVAL, FULL OPEN
.......8N-13
SWITCH - REMOVAL, GLOVE BOX LAMP
. . 8L-22
SWITCH - REMOVAL, HEADLAMP
........8L-13
SWITCH - REMOVAL, IGNITION
.........19-14
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page