2004 CHRYSLER VOYAGER ABS

Alternate Good Trip
Alternate Good Trips are used in place of Global
Good Trips for Comprehensive Components and
Major Monitors. If the Task Manager cannot run a
Global Good Trip because a component fault is stop-
ping the monitor from running, it will attempt to
count an Alternate Good Trip.
The Task Manager counts an Alternate Good Trip
for Comprehensive components when the following
conditions are met:
²Two minutes of engine run time, idle or driving
²No other faults occur
The Task Manager counts an Alternate Good Trip
for a Major Monitor when the monitor runs and
passes. Only the Major Monitor that failed needs to
pass to count an Alternate Good Trip.
Warm-Up Cycles
Once the MIL has been extinguished by the Good
Trip Counter, the PCM automatically switches to a
Warm-Up Cycle Counter that can be viewed on the
DRBIIIt. Warm-Up Cycles are used to erase DTCs
and Freeze Frames. Forty Warm-Up cycles must
occur in order for the PCM to self-erase a DTC and
Freeze Frame. A Warm-Up Cycle is defined as fol-
lows:
²Engine coolant temperature must start below
and rise above 160É F
²Engine coolant temperature must rise by 40É F
²No further faults occur
Freeze Frame Data Storage
Once a failure occurs, the Task Manager records
several engine operating conditions and stores it in a
Freeze Frame. The Freeze Frame is considered one
frame of information taken by an on-board data
recorder. When a fault occurs, the PCM stores the
input data from various sensors so that technicians
can determine under what vehicle operating condi-
tions the failure occurred.
The data stored in Freeze Frame is usually
recorded when a system fails the first time for two
trip faults. Freeze Frame data will only be overwrit-
ten by a different fault with a higher priority.
CAUTION: Erasing DTCs, either with the DRBIIIT;or
by disconnecting the battery, also clears all Freeze
Frame data.
Similar Conditions Window
The Similar Conditions Window displays informa-
tion about engine operation during a monitor. Abso-
lute MAP (engine load) and Engine RPM are stored
in this window when a failure occurs. There are two
different Similar conditions Windows: Fuel System
and Misfire.FUEL SYSTEM
²Fuel System Similar Conditions WindowÐ
An indicator that 'Absolute MAP When Fuel Sys Fail'
and 'RPM When Fuel Sys Failed' are all in the same
range when the failure occurred. Indicated by switch-
ing from 'NO' to 'YES'.
²Absolute MAP When Fuel Sys FailÐ The
stored MAP reading at the time of failure. Informs
the user at what engine load the failure occurred.
²Absolute MAPÐ A live reading of engine load
to aid the user in accessing the Similar Conditions
Window.
²RPM When Fuel Sys FailÐ The stored RPM
reading at the time of failure. Informs the user at
what engine RPM the failure occurred.
²Engine RPMÐ A live reading of engine RPM
to aid the user in accessing the Similar Conditions
Window.
²Adaptive Memory FactorÐ The PCM utilizes
both Short Term Compensation and Long Term Adap-
tive to calculate the Adaptive Memory Factor for
total fuel correction.
²Upstream O2S VoltsÐ A live reading of the
Oxygen Sensor to indicate its performance. For
example, stuck lean, stuck rich, etc.
²SCW Time in Window (Similar Conditions
Window Time in Window)Ð A timer used by the
PCM that indicates that, after all Similar Conditions
have been met, if there has been enough good engine
running time in the SCW without failure detected.
This timer is used to increment a Good Trip.
²Fuel System Good Trip CounterÐATrip
Counter used to turn OFF the MIL for Fuel System
DTCs. To increment a Fuel System Good Trip, the
engine must be in the Similar Conditions Window,
Adaptive Memory Factor must be less than cali-
brated threshold and the Adaptive Memory Factor
must stay below that threshold for a calibrated
amount of time.
²Test Done This TripÐ Indicates that the
monitor has already been run and completed during
the current trip.
MISFIRE
²Same Misfire Warm-Up StateÐ Indicates if
the misfire occurred when the engine was warmed up
(above 160É F).
²In Similar Misfire WindowÐ An indicator
that 'Absolute MAP When Misfire Occurred' and
'RPM When Misfire Occurred' are all in the same
range when the failure occurred. Indicated by switch-
ing from 'NO' to 'YES'.
²Absolute MAP When Misfire OccurredÐ
The stored MAP reading at the time of failure.
Informs the user at what engine load the failure
occurred.
25 - 26 ON-BOARD DIAGNOSTICSRS
TASK MANAGER (Continued)

²Absolute MAPÐ A live reading of engine load
to aid the user in accessing the Similar Conditions
Window.
²RPM When Misfire OccurredÐ The stored
RPM reading at the time of failure. Informs the user
at what engine RPM the failure occurred.
²Engine RPMÐ A live reading of engine RPM
to aid the user in accessing the Similar Conditions
Window.
²Adaptive Memory FactorÐ The PCM utilizes
both Short Term Compensation and Long Term Adap-tive to calculate the Adaptive Memory Factor for
total fuel correction.
²200 Rev CounterÐ Counts 0±100 720 degree
cycles.
²SCW Cat 200 Rev CounterÐ Counts when in
similar conditions.
²SCW FTP 1000 Rev CounterÐ Counts 0±4
when in similar conditions.
²Misfire Good Trip CounterÐ Counts up to
three to turn OFF the MIL.
RSON-BOARD DIAGNOSTICS25-27
TASK MANAGER (Continued)

INDEX
ABS FASTENER TORQUE,
SPECIFICATIONS......................5-79
ABSORBER - DESCRIPTION, SHOCK.......2-37
ABSORBER - INSTALLATION, SHOCK......2-38
ABSORBER - OPERATION, SHOCK........2-37
ABSORBER - REMOVAL, SHOCK..........2-37
ABSORBER (UPPER BUSHING) -
ASSEMBLY, SHOCK....................2-38
ABSORBER (UPPER BUSHING) -
DISASSEMBLY, SHOCK.................2-37
A/C COMPRESSOR - DESCRIPTION......24-73
A/C COMPRESSOR - OPERATION........24-73
A/C COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING.............24-15
A/C COMPRESSOR CLUTCH RELAY -
DESCRIPTION.......................24-19
A/C COMPRESSOR CLUTCH RELAY -
INSTALLATION.......................24-20
A/C COMPRESSOR CLUTCH RELAY -
OPERATION.........................24-19
A/C COMPRESSOR CLUTCH RELAY -
REMOVAL..........................24-20
A/C COMPRESSOR CLUTCH/COIL -
DESCRIPTION.......................24-15
A/C COMPRESSOR CLUTCH/COIL -
INSPECTION........................24-17
A/C COMPRESSOR CLUTCH/COIL -
INSTALLATION.......................24-17
A/C COMPRESSOR CLUTCH/COIL -
OPERATION.........................24-15
A/C COMPRESSOR CLUTCH/COIL -
REMOVAL..........................24-16
A/C COMPRESSOR MOUNTING BRACKET
- 2.4L ENGINE - INSTALLATION.........24-76
A/C COMPRESSOR MOUNTING BRACKET
- 2.4L ENGINE - REMOVAL.............24-75
A/C CONDENSER - DESCRIPTION........24-76
A/C CONDENSER - INSTALLATION.......24-78
A/C CONDENSER - OPERATION..........24-76
A/C CONDENSER - REMOVAL...........24-77
A/C COOL DOWN TEST - DIAGNOSIS
AND TESTING........................24-6
A/C DISCHARGE LINE - INSTALLATION . . . 24-80
A/C DISCHARGE LINE - REMOVAL.......24-79
A/C EVAPORATOR - DESCRIPTION . . 24-80,24-97
A/C EVAPORATOR - INSTALLATION......24-80
A/C EVAPORATOR - INSTALLATION,
REAR..............................24-99
A/C EVAPORATOR - OPERATION....24-80,24-97
A/C EVAPORATOR - REMOVAL..........24-80
A/C EVAPORATOR - REMOVAL, REAR.....24-97
A/C EVAPORATOR LINE EXTENSION -
INSTALLATION, REAR.................24-99
A/C EVAPORATOR LINE EXTENSION -
REMOVAL..........................24-98
A/C EXPANSION VALVE - DESCRIPTION . . . 24-99
A/C EXPANSION VALVE - DIAGNOSIS
AND TESTING.......................24-81
A/C EXPANSION VALVE - INSTALLATION . 24-100
A/C EXPANSION VALVE - OPERATION.....24-99
A/C EXPANSION VALVE - REMOVAL.....24-100
A/C HEATER CONTROL - DESCRIPTION . . . 24-20
A/C HEATER CONTROL - INSTALLATION . . . 24-21
A/C HEATER CONTROL - REMOVAL......24-21
A/C PERFORMANCE TEST - DIAGNOSIS
AND TESTING........................24-7
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-21
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-22
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-22
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-21
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-22
A/C SYSTEM, CAUTION................24-66
A/C SYSTEM, SPECIFICATIONS..........24-11
A/C SYSTEM, WARNING...............24-65
ACCELERATOR PEDAL - INSTALLATION . . . 14-24
ACCELERATOR PEDAL - REMOVAL
.......14-24
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING
.........................7-7
ACCESSORY DRIVE BELT TENSION,
SPECIFICATIONS
.......................7-5
ACCUMULATOR - DESCRIPTION
.......21-188,
21s-206,21s-94
ACCUMULATOR - OPERATION
....21-189,21s-94A/C-HEATER CONTROL - DESCRIPTION . . . 24-34
A/C-HEATER CONTROL - INSTALLATION . . . 24-35
A/C-HEATER CONTROL - OPERATION.....24-34
A/C-HEATER CONTROL - REMOVAL......24-34
A/C-HEATER CONTROL CALIBRATION -
STANDARD PROCEDURE...............24-20
ACTUATOR - DESCRIPTION, BLEND
DOOR........................24-23,24-35
ACTUATOR - DESCRIPTION, ENGAGE.....8N-10
ACTUATOR - DESCRIPTION, LATCH......8N-14
ACTUATOR - DESCRIPTION, MODE
DOOR.............................24-30
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR................24-32
ACTUATOR - INSTALLATION, BLEND
DOOR........................24-23,24-36
ACTUATOR - INSTALLATION, ENGAGE....8N-11
ACTUATOR - INSTALLATION, INSIDE
HANDLE............................23-27
ACTUATOR - INSTALLATION, LATCH.....8N-14
ACTUATOR - INSTALLATION, MODE
DOOR.............................24-31
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-33
ACTUATOR - OPERATION, BLEND DOOR . . 24-23,
24-35
ACTUATOR - OPERATION, ENGAGE......8N-11
ACTUATOR - OPERATION, LATCH........8N-14
ACTUATOR - OPERATION, MODE DOOR . . . 24-30
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-32
ACTUATOR - REAR - DESCRIPTION,
MODE DOOR........................24-39
ACTUATOR - REAR - INSTALLATION,
MODE DOOR........................24-40
ACTUATOR - REAR - OPERATION, MODE
DOOR.............................24-40
ACTUATOR - REAR - REMOVAL, MODE
DOOR.............................24-40
ACTUATOR - REMOVAL, BLEND DOOR . . . 24-23,
24-36
ACTUATOR - REMOVAL, ENGAGE........8N-11
ACTUATOR - REMOVAL, INSIDE HANDLE . . 23-27
ACTUATOR - REMOVAL, LATCH.........8N-14
ACTUATOR - REMOVAL, MODE DOOR....24-30
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-33
ADAPTER - INSTALLATION, FRONT DISC
BRAKE CALIPER.................5-31,5s-30
ADAPTER - INSTALLATION, OIL FILTER . . . 9-139
ADAPTER - REMOVAL, FRONT DISC
BRAKE CALIPER.................5-31,5s-30
ADAPTER - REMOVAL, OIL FILTER.......9-139
ADAPTIVE MEMORIES, OPERATION -
FUEL CORRECTION OR................14-20
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE.................7-5
ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING...................7-5
ADHESIVE ATTACHED - INSTALLATION,
EXTERIOR NAME PLATES..............23-51
ADHESIVE ATTACHED - REMOVAL,
EXTERIOR NAME PLATES..............23-51
ADHESIVE LOCATIONS -
SPECIFICATIONS, STRUCTURAL
........23-156
ADJUSTABLE - INSTALLATION, PEDALS
. . . 5s-40
ADJUSTABLE - REMOVAL, PEDALS
.......5s-38
ADJUSTABLE PEDALS SWITCH -
INSTALLATION
.......................5s-10
ADJUSTABLE PEDALS SWITCH -
REMOVAL
..........................5s-10
ADJUSTER-BORC-PILLAR -
INSTALLATION, SEAT BELT HEIGHT
......8O-13
ADJUSTER-BORC-PILLAR -
REMOVAL, SEAT BELT HEIGHT
..........8O-13
ADJUSTER - DIAGNOSIS AND TESTING,
DRUM BRAKE AUTOMATIC
.........5-13,5s-13
ADJUSTER - INSTALLATION, FRONT
SEAT TRACK MANUAL
................23-95
ADJUSTER - INSTALLATION, FRONT
SEAT TRACK POWER
.................23-95
ADJUSTER - REMOVAL, FRONT SEAT
TRACK MANUAL
.....................23-95
ADJUSTER - REMOVAL, FRONT SEAT
TRACK POWER
......................23-95
ADJUSTER KNOB - INSTALLATION, SEAT
BELT HEIGHT
.......................8O-14ADJUSTER KNOB - REMOVAL, SEAT
BELT HEIGHT.......................8O-14
ADJUSTER NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING, HYDRAULIC
LASH...............................9-34
ADJUSTER TENSION RELEASE -
STANDARD PROCEDURE, PARKING
BRAKE AUTOMATIC...............5-58,5s-61
ADJUSTER TENSION RESET -
STANDARD PROCEDURE, PARKING
BRAKE AUTOMATIC...............5-59,5s-61
ADJUSTERS - INSTALLATION,
HYDRAULIC LASH.....................9-34
ADJUSTERS - REMOVAL, HYDRAULIC
LASH...............................9-34
AERATION - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-3
AFTER AN AIRBAG DEPLOYMENT -
STANDARD PROCEDURE, SERVICE.......8O-3
AIR CLEANER ELEMENT - INSTALLATION . . 9-24,
9-98
AIR CLEANER ELEMENT - REMOVAL . . 9-24,9-98
AIR CLEANER HOUSING - INSTALLATION . . 9-24,
9-99
AIR CLEANER HOUSING - REMOVAL . . 9-24,9-99
AIR CONDITIONER - DESCRIPTION,
HEATER .............................24-1
AIR CONDITIONER - OPERATION,
HEATER .............................24-4
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-28
AIR CONTROL MOTOR - INSTALLATION,
IDLE...............................14-29
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-28
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-29
AIR EXHAUSTER - DESCRIPTION, REAR
QUARTER PANEL/FENDER..............23-57
AIR EXHAUSTER - INSTALLATION, REAR
QUARTER PANEL/FENDER..............23-58
AIR EXHAUSTER - REMOVAL, REAR
QUARTER PANEL/FENDER..............23-57
AIR FILTER - DESCRIPTION............24-43
AIR FILTER - INSTALLATION............24-44
AIR FILTER - REMOVAL...............24-43
AIR GAP, SPECIFICATIONS - WHEEL
SPEED SENSOR.......................5-79
AIR INTAKE PIPE - INSTALLATION......24-114
AIR INTAKE PIPE - REMOVAL..........24-113
AIR OUTLETS - DESCRIPTION.....24-44,24-56
AIR OUTLETS - INSTALLATION..........24-56
AIR OUTLETS - REMOVAL.............24-56
AIR PRESSURE TESTS - DIAGNOSIS
AND TESTING, CLUTCH.........21-122,21s-30
AIR TEMPERATURE SENSOR -
DESCRIPTION, INLET.................14-30
AIRBAG - DESCRIPTION, DRIVER........8O-6
AIRBAG - DESCRIPTION, PASSENGER.....8O-8
AIRBAG - DESCRIPTION, SEAT..........8O-11
AIRBAG - INSTALLATION, DRIVER........8O-7
AIRBAG - INSTALLATION, PASSENGER . . . 8O-10
AIRBAG - OPERATION, DRIVER..........8O-6
AIRBAG - OPERATION, PASSENGER.......8O-9
AIRBAG - OPERATION, SEAT...........8O-11
AIRBAG - REMOVAL, DRIVER
............8O-6
AIRBAG - REMOVAL, PASSENGER
........8O-9
AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN
........8O-3
AIRBAG SYSTEM - DIAGNOSIS AND
TESTING
............................8O-2
AIRBAG TRIM COVER - INSTALLATION,
DRIVER
.............................8O-7
AIRBAG TRIM COVER - REMOVAL,
DRIVER
.............................8O-7
AIRBAGS - STANDARD PROCEDURE,
HANDLING
..........................8O-3
AJAR SWITCH - EXPORT -
INSTALLATION, HOOD
.................8Q-3
AJAR SWITCH - EXPORT - REMOVAL,
HOOD
..............................8Q-3
ALIGNMENT - DESCRIPTION, WHEEL
......2-47
ALIGNMENT - EXPORT - STANDARD
PROCEDURE, FRONT FOG LAMP UNIT
.....8L-9
ALIGNMENT - EXPORT - STANDARD
PROCEDURE, HEADLAMP UNIT
.........8L-14
ALIGNMENT - STANDARD PROCEDURE,
FRONT FOG LAMP UNIT
................8L-9
RSINDEX1
Description Group-Page Description Group-Page Description Group-Page

BLEEDING - STANDARD PROCEDURE,
BASE BRAKE......................5-7,5s-7
BLEEDING - STANDARD PROCEDURE,
MASTER CYLINDER...............5-35,5s-34
BLEND DOOR ACTUATOR -
DESCRIPTION..................24-23,24-35
BLEND DOOR ACTUATOR -
INSTALLATION..................24-23,24-36
BLEND DOOR ACTUATOR - OPERATION . . 24-23,
24-35
BLEND DOOR ACTUATOR - REMOVAL....24-23,
24-36
BLOCK - CLEANING, ENGINE.......9-112,9-36
BLOCK - DESCRIPTION, BLOWER
MOTOR RESISTOR...................24-26
BLOCK - DESCRIPTION, ENGINE.....9-112,9-35
BLOCK - DESCRIPTION, NON-ABS
JUNCTION......................5-33,5s-32
BLOCK - DIAGNOSIS AND TESTING,
BLOWER MOTOR RESISTOR............24-26
BLOCK - DIAGNOSIS AND TESTING,
REAR BLOWER MOTOR RESISTOR......24-38
BLOCK - INSPECTION, ENGINE......9-112,9-36
BLOCK - INSTALLATION, BLOWER
MOTOR RESISTOR...................24-27
BLOCK - INSTALLATION, NON-ABS
JUNCTION......................5-33,5s-32
BLOCK - OPERATION, BLOWER MOTOR
RESISTOR..........................24-26
BLOCK - OPERATION, NON-ABS
JUNCTION......................5-33,5s-32
BLOCK - REMOVAL, BLOWER MOTOR
RESISTOR...........................24-26
BLOCK - REMOVAL, NON-ABS JUNCTION . . 5-33,
5s-32
BLOCK HEATER - DESCRIPTION, ENGINE . . . 7-20
BLOCK HEATER - INSTALLATION,
ENGINE.............................7-20
BLOCK HEATER - OPERATION, ENGINE....7-20
BLOCK HEATER - REMOVAL, ENGINE......7-20
BLOCK HEATER TESTING - DIAGNOSIS
AND TESTING, ENGINE.................7-20
BLOCKER LATCH - INSTALLATION, FUEL
FILL DOOR.........................23-53
BLOCKER LATCH - REMOVAL, FUEL FILL
DOOR.............................23-53
BLOCKER LATCH STRIKER -
INSTALLATION, FUEL FILL DOOR........23-53
BLOCKER LATCH STRIKER - REMOVAL,
FUEL FILL DOOR.....................23-53
BLOCKER LOCKOUT LINK -
INSTALLATION, FUEL FILL DOOR........23-54
BLOCKER LOCKOUT LINK - REMOVAL,
FUEL FILL DOOR.....................23-53
BLOWER MOTOR - DESCRIPTION . . 24-46,24-57
BLOWER MOTOR - DESCRIPTION,
POWER MODULE....................24-31
BLOWER MOTOR - DESCRIPTION,
POWER MODULE - REAR..............24-41
BLOWER MOTOR - DIAGNOSIS AND
TESTING...........................24-47
BLOWER MOTOR - DIAGNOSIS AND
TESTING, REAR......................24-58
BLOWER MOTOR - INSTALLATION . . 24-49,24-58
BLOWER MOTOR - INSTALLATION,
POWER MODULE....................24-32
BLOWER MOTOR - INSTALLATION,
POWER MODULE - REAR..............24-42
BLOWER MOTOR - OPERATION....24-46,24-57
BLOWER MOTOR - OPERATION, POWER
MODULE...........................24-31
BLOWER MOTOR - OPERATION, POWER
MODULE - REAR.....................24-41
BLOWER MOTOR - REMOVAL......24-47,24-58
BLOWER MOTOR - REMOVAL, POWER
MODULE...........................24-31
BLOWER MOTOR - REMOVAL, POWER
MODULE - REAR.....................24-41
BLOWER MOTOR RELAY - DESCRIPTION
. 24-24,
24-37
BLOWER MOTOR RELAY -
INSTALLATION
..................24-25,24-38
BLOWER MOTOR RELAY - OPERATION
. . . 24-24,
24-37
BLOWER MOTOR RELAY - REMOVAL
....24-25,
24-38
BLOWER MOTOR RESISTOR -
DESCRIPTION
.......................24-38BLOWER MOTOR RESISTOR -
INSTALLATION.......................24-39
BLOWER MOTOR RESISTOR -
OPERATION.........................24-38
BLOWER MOTOR RESISTOR - REMOVAL . . 24-39
BLOWER MOTOR RESISTOR BLOCK -
DESCRIPTION.......................24-26
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING.............24-26
BLOWER MOTOR RESISTOR BLOCK -
DIAGNOSIS AND TESTING, REAR........24-38
BLOWER MOTOR RESISTOR BLOCK -
INSTALLATION.......................24-27
BLOWER MOTOR RESISTOR BLOCK -
OPERATION.........................24-26
BLOWER MOTOR RESISTOR BLOCK -
REMOVAL..........................24-26
BODY - ASSEMBLY, VALVE.....21-257,21s-159,
21s-212
BODY - DESCRIPTION, THROTTLE.......14-35
BODY - DESCRIPTION, VALVE . . . 21-250,21s-152
BODY - DISASSEMBLY, VALVE . . 21-252,21s-155,
21s-208
BODY - INSTALLATION, THROTTLE.......14-35
BODY - INSTALLATION, VALVE . . 21-262,21s-164,
21s-217
BODY - OPERATION, THROTTLE.........14-35
BODY - OPERATION, VALVE....21-250,21s-152
BODY - REMOVAL, THROTTLE..........14-35
BODY - REMOVAL, VALVE.....21-251,21s-153,
21s-206
BODY AND CABLE - DESCRIPTION,
ANTENNA...........................8A-4
BODY AND CABLE - DIAGNOSIS AND
TESTING, ANTENNA...................8A-4
BODY AND CABLE - INSTALLATION,
ANTENNA...........................8A-6
BODY AND CABLE - OPERATION,
ANTENNA...........................8A-4
BODY AND CABLE - REMOVAL,
ANTENNA...........................8A-5
BODY CODE PLATE - DESCRIPTION.....Intro.-1
BODY CONTROL MODULE -
DESCRIPTION........................8s-1
BODY CONTROL MODULE -
DESCRIPTION........................8E-3
BODY CONTROL MODULE -
INSTALLATION........................8s-3
BODY CONTROL MODULE -
INSTALLATION........................8E-5
BODY CONTROL MODULE - OPERATION . . . 8s-1
BODY CONTROL MODULE - OPERATION . . . 8E-3
BODY CONTROL MODULE - REMOVAL.....8s-3
BODY CONTROL MODULE - REMOVAL.....8E-4
BODY LUBRICATION, SPECIFICATIONS....23-12
BODY OPENING DIMENSIONS -
SPECIFICATIONS....................23-127
BODY PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC.................23-3
BODY SEALING LOCATIONS -
SPECIFICATIONS....................23-130
BODY SIDE MOLDINGS - INSTALLATION . . 23-46
BODY SIDE MOLDINGS - REMOVAL......23-45
BODY, SPECIAL TOOLS................23-13
BOLSTER - INSTALLATION, QUARTER
TRIM..............................23-79
BOLSTER - REMOVAL, QUARTER TRIM . . . 23-79
BOOSTER - DESCRIPTION, POWER
BRAKE.........................5-40,5s-43
BOOSTER - DIAGNOSIS AND TESTING,
POWER BRAKE..................5-41,5s-44
BOOSTER - OPERATION, POWER BRAKE . . 5-41,
5s-44
BOOT - INNER - INSTALLATION, CV........3-6
BOOT - INNER - REMOVAL, CV...........3-6
BOOT - INNER/OUTER - INSTALLATION,
CV .................................3-17
BOOT - INNER/OUTER - REMOVAL, CV....3-15
BOOT - INSTALLATION, GEARSHIFT......21-73
BOOT - OUTER - INSTALLATION, CV......3-10
BOOT - OUTER - REMOVAL, CV..........3-10
BOOT - REMOVAL, GEARSHIFT
..........21-72
BORE FITTING - STANDARD
PROCEDURE, PISTON TO CYLINDER
......9-42
BORE HONING - STANDARD
PROCEDURE, CYLINDER
...........9-112,9-35
BOX - INSTALLATION, GLOVE
...........23-64
BOX - REMOVAL, GLOVE
..............23-64BOX LAMP SWITCH - INSTALLATION,
GLOVE.............................8L-22
BOX LAMP SWITCH - REMOVAL, GLOVE . . 8L-22
BOX LATCH - INSTALLATION, GLOVE.....23-64
BOX LATCH - REMOVAL, GLOVE.........23-64
BOX LATCH STRIKER - INSTALLATION,
GLOVE.............................23-64
BOX LATCH STRIKER - REMOVAL,
GLOVE.............................23-64
B-PILLAR - INSTALLATION, A-PILLAR-
HEADER, OR........................23-17
B-PILLAR - REMOVAL, A-PILLAR-
HEADER, OR........................23-17
B-PILLAR LOWER TRIM - INSTALLATION . . 23-75
B-PILLAR LOWER TRIM - REMOVAL.....23-74
B-PILLAR SWITCH - DESCRIPTION, LEFT . 8N-32
B-PILLAR SWITCH - DESCRIPTION,
RIGHT.............................8N-32
B-PILLAR SWITCH - INSTALLATION,
LEFT..............................8N-32
B-PILLAR SWITCH - INSTALLATION,
RIGHT.............................8N-32
B-PILLAR SWITCH - OPERATION, LEFT . . . 8N-32
B-PILLAR SWITCH - OPERATION, RIGHT . . 8N-32
B-PILLAR SWITCH - REMOVAL, LEFT....8N-32
B-PILLAR SWITCH - REMOVAL, RIGHT . . . 8N-32
B-PILLAR UPPER TRIM - INSTALLATION . . 23-75
B-PILLAR UPPER TRIM - REMOVAL......23-75
BRACKET - 2.4L ENGINE -
INSTALLATION, A/C COMPRESSOR
MOUNTING.........................24-76
BRACKET - 2.4L ENGINE - REMOVAL,
A/C COMPRESSOR MOUNTING..........24-75
BRACKET - DESCRIPTION, TRANSVERSE . . 8N-18
BRACKET - INSTALLATION, TRANSVERSE . 8N-18
BRACKET - OPERATION, TRANSVERSE . . . 8N-18
BRACKET - REMOVAL, TRANSVERSE.....8N-18
BRACKET ASSEMBLY - INSTALLATION,
FLOOR CONSOLE TRAY................23-83
BRACKET ASSEMBLY - REMOVAL,
FLOOR CONSOLE TRAY................23-83
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK...........................8E-5
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK...........................8E-6
BRAKE - INSTALLATION, LEVER -
PARKING.......................5-65,5s-67
BRAKE - INSTALLATION, SHOES -
PARKING.......................5-72,5s-75
BRAKE - INSTALLATION, SUPPORT
PLATE - DRUM..................5-56,5s-58
BRAKE - OPERATION, CONTROLLER
ANTILOCK...........................8E-5
BRAKE - REMOVAL, CONTROLLER
ANTILOCK...........................8E-6
BRAKE - REMOVAL, LEVER - PARKING....5-64,
5s-67
BRAKE - REMOVAL, SHOES - PARKING . . . 5-67,
5s-69
BRAKE - REMOVAL, SUPPORT PLATE -
DRUM
.........................5-56,5s-58
BRAKE AUTOMATIC ADJUSTER -
DIAGNOSIS AND TESTING, DRUM
. . . 5-13,5s-13
BRAKE AUTOMATIC ADJUSTER TENSION
RELEASE - STANDARD PROCEDURE,
PARKING
.......................5-58,5s-61
BRAKE AUTOMATIC ADJUSTER TENSION
RESET - STANDARD PROCEDURE,
PARKING
.......................5-59,5s-61
BRAKE BLEEDING - STANDARD
PROCEDURE, BASE
.................5-7,5s-7
BRAKE BOOSTER - DESCRIPTION,
POWER
........................5-40,5s-43
BRAKE BOOSTER - DIAGNOSIS AND
TESTING, POWER
................5-41,5s-44
BRAKE BOOSTER - OPERATION, POWER
. . 5-41,
5s-44
BRAKE CABLE (FRONT) - INSTALLATION,
PARKING
.......................5-63,5s-65
BRAKE CABLE (FRONT) - REMOVAL,
PARKING
.......................5-59,5s-62
BRAKE CABLE (INTERMEDIATE) -
INSTALLATION, PARKING
..........5-63,5s-66
BRAKE CABLE (INTERMEDIATE) -
REMOVAL, PARKING
..............5-60,5s-62
BRAKE CABLE (LEFT REAR) -
INSTALLATION, PARKING
..........5-64,5s-66
4 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

ENGINE OIL LEVEL CHECK, STANDARD
PROCEDURE.........................9-53
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING.......................9-136
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING, CHECKING...............9-52
ENGINE, SPECIAL TOOLS - 2.4L..........9-21
ENGINE, SPECIAL TOOLS - 3.3/3.8L.......9-95
ENGINE, SPECIFICATIONS - 3.3/3.8L . . 9-91,9s-11
ENGINE SPEED SENSOR - DESCRIPTION . . 14-26
ENGINE SPEED SENSOR - OPERATION....14-26
ENGINES - DESCRIPTION, ENGINE OIL -
DIESEL..............................0-6
ENGINES - DIAGNOSIS AND TESTING,
SYSTEM CHARGE LEVEL TEST -
GASOLINE..........................24-67
ENGINES - EXPORT - DESCRIPTION,
DIESEL.............................0-24
ENTRY MODULE - DESCRIPTION,
REMOTE KEYLESS...................8N-43
ENTRY MODULE - DESCRIPTION,
SENTRY KEY REMOTE.................8Q-3
ENTRY MODULE - DIAGNOSIS AND
TESTING, REMOTE KEYLESS...........8N-43
ENTRY MODULE - DIAGNOSIS AND
TESTING, SENTRY KEY REMOTE.........8Q-5
ENTRY MODULE - INSTALLATION,
REMOTE KEYLESS...................8N-44
ENTRY MODULE - INSTALLATION,
SENTRY KEY REMOTE.................8Q-6
ENTRY MODULE - OPERATION, REMOTE
KEYLESS...........................8N-43
ENTRY MODULE - OPERATION, SENTRY
KEY REMOTE........................8Q-4
ENTRY MODULE - REMOVAL, REMOTE
KEYLESS...........................8N-44
ENTRY MODULE - REMOVAL, SENTRY
KEY REMOTE........................8Q-5
ENTRY SYSTEM - DIAGNOSIS AND
TESTING, SENTRY KEY REMOTE.........8Q-3
ENTRY TRANSMITTER - DIAGNOSIS AND
TESTING, KEYLESS..............8N-42,8N-5
ENTRY TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE, REMOTE
KEYLESS............................8N-5
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-70
ERASING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-11
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-72
EVAP CANISTER - INSTALLATION, REAR . . 25-20
EVAP CANISTER - REMOVAL, REAR......25-19
EVAPORATION CONTROL SYSTEM -
OPERATION.........................25-10
EVAPORATOR - DESCRIPTION, A/C . 24-80,24-97
EVAPORATOR - INSTALLATION, A/C......24-80
EVAPORATOR - INSTALLATION, REAR
A/C................................24-99
EVAPORATOR - OPERATION, A/C . . . 24-80,24-97
EVAPORATOR - REMOVAL, A/C..........24-80
EVAPORATOR - REMOVAL, REAR A/C.....24-97
EVAPORATOR LINE EXTENSION -
INSTALLATION, REAR A/C..............24-99
EVAPORATOR LINE EXTENSION -
REMOVAL, A/C......................24-98
EVAPORATOR TEMPERATURE SENSOR -
DESCRIPTION.......................24-27
EVAPORATOR TEMPERATURE SENSOR -
OPERATION.........................24-28
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-12
EVAP/PURGE SOLENOID - INSTALLATION . 25-12
EVAP/PURGE SOLENOID - OPERATION....25-12
EVAP/PURGE SOLENOID - REMOVAL.....25-12
EXCESSIVE EXHAUST SYSTEM NOISE -
DIAGNOSIS AND TESTING..............11-2
EXHAUST MANIFOLD - CLEANING........9-61
EXHAUST MANIFOLD - INSPECTION.......9-61
EXHAUST MANIFOLD - INSTALLATION.....9-61
EXHAUST MANIFOLD - LEFT - CLEANING . . 9-152
EXHAUST MANIFOLD - LEFT -
INSPECTION
........................9-152
EXHAUST MANIFOLD - LEFT -
INSTALLATION
.......................9-152
EXHAUST MANIFOLD - LEFT - REMOVAL
. . 9-152
EXHAUST MANIFOLD - REMOVAL
.........9-61
EXHAUST MANIFOLD - RIGHT -
CLEANING
..........................9-151EXHAUST MANIFOLD - RIGHT -
INSPECTION........................9-151
EXHAUST MANIFOLD - RIGHT -
INSTALLATION.......................9-151
EXHAUST MANIFOLD - RIGHT -
REMOVAL..........................9-150
EXHAUST SYSTEM - DESCRIPTION.......11-1
EXHAUST SYSTEM NOISE - DIAGNOSIS
AND TESTING, EXCESSIVE..............11-2
EXHAUST SYSTEM RESTRICTION CHECK
- DIAGNOSIS AND TESTING.............11-2
EXHAUST SYSTEM, SPECIAL TOOLS......11-4
EXHAUST TUBE - INSTALLATION.......24-115
EXHAUST TUBE - REMOVAL...........24-114
EXHAUSTER - DESCRIPTION, REAR
QUARTER PANEL/FENDER AIR..........23-57
EXHAUSTER - INSTALLATION, REAR
QUARTER PANEL/FENDER AIR..........23-58
EXHAUSTER - REMOVAL, REAR
QUARTER PANEL/FENDER AIR..........23-57
EXPANSION VALVE - DESCRIPTION......24-81
EXPANSION VALVE - DESCRIPTION, A/C . . 24-99
EXPANSION VALVE - DIAGNOSIS AND
TESTING..........................24-100
EXPANSION VALVE - DIAGNOSIS AND
TESTING, A/C.......................24-81
EXPANSION VALVE - INSTALLATION......24-82
EXPANSION VALVE - INSTALLATION, A/C . 24-100
EXPANSION VALVE - OPERATION........24-81
EXPANSION VALVE - OPERATION, A/C....24-99
EXPANSION VALVE - REMOVAL.........24-82
EXPANSION VALVE - REMOVAL, A/C.....24-100
EXPORT - BRAKE ROTOR..........5-55,5s-58
EXPORT - DESCRIPTION...........5-58,5s-60
EXPORT - DESCRIPTION................0-15
EXPORT - DESCRIPTION................2-10
EXPORT - DESCRIPTION, ANTENNA
MODULE............................8A-6
EXPORT - DESCRIPTION, DIESEL
ENGINES............................0-24
EXPORT - DESCRIPTION, DOOR
CYLINDER LOCK SWITCH...............8N-3
EXPORT - DESCRIPTION, POWER
FOLDAWAY MIRROR SWITCH..........8N-48
EXPORT - DESCRIPTION, QUARTER
GLASS INTEGRAL ANTENNA.............8A-9
EXPORT - DIAGNOSIS AND TESTING,
ANTENNA MODULE....................8A-7
EXPORT - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK SWITCH.........8N-3
EXPORT - DIAGNOSIS AND TESTING,
QUARTER GLASS INTEGRAL ANTENNA....8A-9
EXPORT - INSTALLATION...............2-11
EXPORT - INSTALLATION, ANTENNA
MODULE............................8A-7
EXPORT - INSTALLATION, DOOR
CYLINDER LOCK SWITCH...............8N-4
EXPORT - INSTALLATION, HEADLAMP
UNIT..............................8L-17
EXPORT - INSTALLATION, HOOD AJAR
SWITCH............................8Q-3
EXPORT - INSTALLATION, POWER
FOLDAWAY MIRROR SWITCH..........8N-49
EXPORT - OPERATION, ANTENNA
MODULE............................8A-6
EXPORT - OPERATION, DOOR CYLINDER
LOCK SWITCH........................8N-3
EXPORT - OPERATION, POWER
FOLDAWAY MIRROR SWITCH..........8N-48
EXPORT - OPERATION, QUARTER GLASS
INTEGRAL ANTENNA...................8A-9
EXPORT - REMOVAL...................2-11
EXPORT - REMOVAL, ANTENNA MODULE . . 8A-7
EXPORT - REMOVAL, DOOR CYLINDER
LOCK SWITCH........................8N-3
EXPORT - REMOVAL, HEADLAMP UNIT . . . 8L-17
EXPORT - REMOVAL, HOOD AJAR
SWITCH............................8Q-3
EXPORT - REMOVAL, POWER
FOLDAWAY MIRROR SWITCH
..........8N-48
EXPORT - STANDARD PROCEDURE,
FRONT FOG LAMP UNIT ALIGNMENT
......8L-9
EXPORT - STANDARD PROCEDURE,
HEADLAMP UNIT ALIGNMENT
..........8L-14
EXTENSION - INSTALLATION, REAR A/C
EVAPORATOR LINE
...................24-99
EXTENSION - REMOVAL, A/C
EVAPORATOR LINE
...................24-98EXTENSION TRIM - INSTALLATION,
A-PILLAR LOWER....................23-74
EXTENSION TRIM - REMOVAL, A-PILLAR
LOWER............................23-74
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - WARNING, LAMPS/
LIGHTING...........................8L-3
EXTERIOR HANDLE - INSTALLATION.....23-22,
23-40
EXTERIOR HANDLE - REMOVAL....23-21,23-40
EXTERIOR HANDLE SWITCH -
DESCRIPTION.......................8N-11
EXTERIOR HANDLE SWITCH -
INSTALLATION......................8N-12
EXTERIOR HANDLE SWITCH -
OPERATION.........................8N-11
EXTERIOR HANDLE SWITCH - REMOVAL . . 8N-11
EXTERIOR LAMPS, SPECIFICATIONS......8L-3
EXTERIOR NAME PLATES - ADHESIVE
ATTACHED - INSTALLATION............23-51
EXTERIOR NAME PLATES - ADHESIVE
ATTACHED - REMOVAL................23-51
EXTERIOR NAME PLATES - TAPE
ATTACHED - INSTALLATION............23-51
EXTERIOR NAME PLATES - TAPE
ATTACHED - REMOVAL................23-51
FACTOR SETTING - STANDARD
PROCEDURE, PINION............8E-15,8E-23
FAILED PARK SWITCH - DIAGNOSIS AND
TESTING..............................8R-2
FAN - DESCRIPTION, RADIATOR..........7-28
FAN - INSTALLATION, RADIATOR.........7-30
FAN - OPERATION, RADIATOR...........7-29
FAN - REMOVAL, RADIATOR.............7-30
FAN MOTOR - DIAGNOSIS AND
TESTING, RADIATOR...................7-29
FAN RELAY - DESCRIPTION, RADIATOR....7-30
FAN RELAY - INSTALLATION, RADIATOR . . . 7-30
FAN RELAY - OPERATION, RADIATOR......7-30
FAN RELAY - REMOVAL, RADIATOR.......7-30
FASCIA - INSTALLATION, FRONT.........13-1
FASCIA - INSTALLATION, REAR..........13-2
FASCIA - REMOVAL, FRONT.............13-1
FASCIA - REMOVAL, REAR..............13-2
FASCIA - SCUFF PAD - INSTALLATION,
REAR...............................13-4
FASCIA - SCUFF PAD - REMOVAL, REAR . . . 13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-2
FASTENER TORQUE, SPECIFICATIONS -
ABS ................................5-79
FASTENER TORQUE, SPECIFICATIONS -
BRAKE...........................5-9,5s-8
FASTENER TORQUE, SPECIFICATIONS -
FRONT SUSPENSION...................2-3
FASTENER TORQUE, SPECIFICATIONS -
POWER STEERING....................19-9
FASTENER TORQUE, SPECIFICATIONS -
REAR SUSPENSION...................2-28
FASTENER USAGE - DESCRIPTION......Intro.-5
FEED CIRCUIT RESISTANCE TEST -
DIAGNOSIS AND TESTING.........8F-32,8F-34
FEED CIRCUIT TEST - DIAGNOSIS AND
TESTING
......................8F-33,8F-35
FENDER - INSTALLATION, FRONT
........23-52
FENDER - REMOVAL, FRONT
...........23-52
FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES NOT
..................25-16
FILL - STANDARD PROCEDURE, FLUID
DRAIN
.............................21-71
FILL DOOR - INSTALLATION, FUEL
.......23-52
FILL DOOR - REMOVAL, FUEL
..........23-52
FILL DOOR BLOCKER LATCH -
INSTALLATION, FUEL
.................23-53
FILL DOOR BLOCKER LATCH -
REMOVAL, FUEL
.....................23-53
FILL DOOR BLOCKER LATCH STRIKER -
INSTALLATION, FUEL
.................23-53
FILL DOOR BLOCKER LATCH STRIKER -
REMOVAL, FUEL
.....................23-53
FILL DOOR BLOCKER LOCKOUT LINK -
INSTALLATION, FUEL
.................23-54
FILL DOOR BLOCKER LOCKOUT LINK -
REMOVAL, FUEL
.....................23-53
RSINDEX13
Description Group-Page Description Group-Page Description Group-Page

INBOARD - 50/50 BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-13
INBOARD - INSTALLATION, SEAT BELT
BUCKLE - FRONT....................8O-12
INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE -
FIRST ROW.........................8O-12
INBOARD - QUAD BUCKET - REMOVAL,
SEAT BELT BUCKLE - FIRST ROW.......8O-12
INBOARD - REMOVAL, SEAT BELT
BUCKLE - FRONT....................8O-12
INDICATOR LAMP - DESCRIPTION,
VTSS/SKIS..........................8Q-7
INDICATOR LAMP - OPERATION,
VTSS/SKIS..........................8Q-8
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR..........22-16,22s-8
INFLATION PRESSURES - STANDARD
PROCEDURE, TIRE..............22-16,22s-8
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-6
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INFRARED TEMPERATURE SENSOR -
DESCRIPTION.......................24-29
INFRARED TEMPERATURE SENSOR -
OPERATION.........................24-29
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-37
INJECTION SYSTEM - OPERATION.......14-18
INJECTOR - DESCRIPTION, FUEL........14-26
INJECTOR - OPERATION, FUEL..........14-26
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-30
INLET FILTER - INSTALLATION..........14-13
INLET FILTER - REMOVAL..............14-13
INLET HOSE - INSTALLATION, HEATER....24-86
INLET HOSE - REMOVAL, HEATER.......24-85
INLET TUBE - 2.4L - DESCRIPTION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - INSTALLATION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - REMOVAL, WATER
PUMP..............................7-35
INLET TUBE - 3.3/3.8L - INSTALLATION,
WATER PUMP........................7-36
INLET TUBE - 3.3/3.8L - REMOVAL,
WATER PUMP........................7-36
INNER - INSTALLATION, CV BOOT.........3-6
INNER - REMOVAL, CV BOOT.............3-6
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-115
INNER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-115
INNER SEAL - INSTALLATION, HALF
SHAFT.............................21-12
INNER SEAL - REMOVAL, HALF SHAFT . . . 21-12
INNER/OUTER - INSTALLATION, CV
BOOT...............................3-17
INNER/OUTER - REMOVAL, CV BOOT......3-15
INPUT - DESCRIPTION, SPEED SENSOR . 21-239,
21s-140
INPUT - INSTALLATION, SPEED
SENSOR....................21-240,21s-141
INPUT - OPERATION, DATA BUS
COMMUNICATION RECEIVE - PCM.......8E-15
INPUT - OPERATION, IGNITION SENSE -
PCM...............................8E-15
INPUT - OPERATION, SENSOR RETURN -
PCM...............................8E-15
INPUT - OPERATION, SPEED SENSOR . . . 21-240,
21s-140
INPUT - REMOVAL, SPEED SENSOR....21-240,
21s-141
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-216,
21s-116
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY...............21-208,21s-107
INPUT FLANGE SEAL - INSTALLATION
.....3-45
INPUT FLANGE SEAL - REMOVAL
.........3-44
INPUT SHAFT - ASSEMBLY
........21-96,21s-5
INPUT SHAFT - DESCRIPTION
.....21-93,21s-1
INPUT SHAFT - DISASSEMBLY
.....21-93,21s-1INPUT SHAFT COVER SEAL -
INSTALLATION.......................21-14
INPUT SHAFT COVER SEAL - REMOVAL . . . 21-13
INPUT SHAFT END SEAL -
INSTALLATION.......................21-16
INPUT SHAFT END SEAL - REMOVAL.....21-15
INPUT SHAFT SEAL - INSTALLATION.....21-18
INPUT SHAFT SEAL - REMOVAL.........21-17
INSIDE HANDLE ACTUATOR -
INSTALLATION.......................23-27
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-27
INSIDE HANDLE CABLE - INSTALLATION . . 23-38
INSIDE HANDLE CABLE - REMOVAL......23-37
INSIDE LATCH HANDLE - INSTALLATION . . 23-34
INSIDE LATCH HANDLE - REMOVAL......23-34
INSPECT, INSPECTION...............21-114
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-1
INSTRUMENT CLUSTER - OPERATION.....8J-1
INSTRUMENT PANEL - INSTALLATION,
LOWER............................23-69
INSTRUMENT PANEL - REMOVAL,
LOWER............................23-69
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-9
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-8
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-66
INSTRUMENT PANEL ASSEMBLY -
REMOVAL............................23-65
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-68
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-68
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-55
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-55
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-55
INSTRUMENT PANEL DUCTS - REMOVAL . 24-55
INSTRUMENT PANEL END CAP -
INSTALLATION.......................23-68
INSTRUMENT PANEL END CAP -
REMOVAL..........................23-68
INSTRUMENT PANEL OUTLET -
INSTALLATION.......................24-46
INSTRUMENT PANEL OUTLET -
REMOVAL..........................24-45
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-69
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-68
INSTRUMENT PANEL TOP PAD
ASSEMBLY - INSTALLATION............23-72
INSTRUMENT PANEL TOP PAD
ASSEMBLY - REMOVAL................23-71
INTAKE MANIFOLD - DESCRIPTION . . 9-144,9-58
INTAKE MANIFOLD - INSTALLATION,
LOWER............................9-149
INTAKE MANIFOLD - INSTALLATION,
UPPER.............................9-147
INTAKE MANIFOLD - LOWER -
CLEANING..........................9-148
INTAKE MANIFOLD - LOWER -
INSPECTION....................9-148,9-60
INTAKE MANIFOLD - LOWER -
INSTALLATION........................9-60
INTAKE MANIFOLD - LOWER - REMOVAL . . 9-60
INTAKE MANIFOLD - REMOVAL, LOWER . . 9-148
INTAKE MANIFOLD - REMOVAL, UPPER . . . 9-145
INTAKE MANIFOLD - UPPER -
INSPECTION.........................9-59
INTAKE MANIFOLD - UPPER -
INSTALLATION........................9-59
INTAKE MANIFOLD - UPPER - REMOVAL . . . 9-58
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING...................9-145,9-58
INTAKE MANIFOLD VACUUM PORT
REPAIR - STANDARD PROCEDURE.......9-145
INTAKE PIPE - INSTALLATION, AIR
......24-114
INTAKE PIPE - REMOVAL, AIR
.........24-113
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.................9-105,9-32,9s-22
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
..............9-104,9-32,9s-21
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...................9-105,9s-22INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..................9-106,9s-23
INTAKE/EXHAUST VALVES & SEATS -
OPERATION....................9-104,9s-21
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.....................9-105,9s-22
INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER GLASS.........8A-9
INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER
GLASS..............................8A-9
INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER GLASS...........8A-9
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-2
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-3
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-2
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-2
INTERACTIVE SPEED CONTROL (4
SPEED EATX ONLY) - OPERATION........8P-2
INTERFACE (PCI) BUS, OPERATION -
PROGRAMMABLE COMMUNICATIONS....14-21
INTERIOR LAMPS, SPECIFICATIONS......8L-20
INTERLOCK - DESCRIPTION, IGNITION....19-17
INTERLOCK SOLENOID - DESCRIPTION,
SHIFT......................21-233,21s-133
INTERLOCK SOLENOID - DIAGNOSIS
AND TESTING, BRAKE/TRANSMISSION
SHIFT......................21-235,21s-135
INTERLOCK SOLENOID - INSTALLATION,
SHIFT.......................21-236,21s-136
INTERLOCK SOLENOID - OPERATION,
SHIFT......................21-233,21s-134
INTERLOCK SOLENOID - REMOVAL,
SHIFT......................21-235,21s-135
INTERLOCK SWITCH - INSTALLATION,
CLUTCH PEDAL.......................6-14
INTERLOCK SWITCH - REMOVAL,
CLUTCH PEDAL.......................6-13
INTERMEDIATE SHAFT - ASSEMBLY....21-107,
21s-17
INTERMEDIATE SHAFT - DESCRIPTION . . 21-100,
21s-9
INTERMEDIATE SHAFT - DISASSEMBLY . 21-100,
21s-10
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-5
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-3,9-76
IOD FUSE - DESCRIPTION...........8W-97-3
IOD FUSE - OPERATION.............8W-97-3
JOINT - DESCRIPTION, LOWER BALL......2-10
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - OPERATION, LOWER BALL.......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-58
JOINT MOLDING - REMOVAL, ROOF......23-58
JOUNCE BUMPER - DESCRIPTION........2-36
JOUNCE BUMPER - OPERATION..........2-36
JUMP STARTING - STANDARD
PROCEDURE.........................0-27
JUNCTION BLOCK - DESCRIPTION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - INSTALLATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - OPERATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - REMOVAL, NON-ABS . . 5-33,
5s-32
KEY - DESCRIPTION, TRANSPONDER.....8Q-6
KEY - OPERATION, TRANSPONDER.......8Q-6
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY................8E-18
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-19
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY
.................8E-18
KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY
............................8E-18
KEY REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY
................8Q-3
KEY REMOTE ENTRY MODULE -
DIAGNOSIS AND TESTING, SENTRY
.......8Q-5
18 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

MOUNTING STUDS - FRONT -
INSTALLATION, WHEEL................22-21
MOUNTING STUDS - FRONT - REMOVAL,
WHEEL............................22-20
MOUNTING STUDS - REAR -
INSTALLATION, WHEEL................22-22
MOUNTING STUDS - REAR - REMOVAL,
WHEEL............................22-21
MOUNTS - FRONT - INSTALLATION,
SPRING.............................2-44
MOUNTS - FRONT - REMOVAL, SPRING . . . 2-43
MOUNTS - REAR - INSTALLATION,
SPRING.............................2-45
MOUNTS - REAR - REMOVAL, SPRING....2-44
MUFFLER - INSTALLATION..............11-7
MUFFLER - REMOVAL..................11-7
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-18
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-18
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - ADHESIVE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - ADHESIVE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NAME PLATES - TAPE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - TAPE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-13
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-13
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP TO FILLER..............7-27
NGC CONTROLLER - REMOVAL.........8E-17
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-47
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-47
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-47
NO CUPHOLDER - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NO CUPHOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NOISE - DIAGNOSIS AND TESTING,
EXCESSIVE EXHAUST SYSTEM...........11-2
NOISE - DIAGNOSIS AND TESTING,
REAR DRIVELINE MODULE..............3-24
NOISE - DIAGNOSIS AND TESTING, TIRE . 22-14,
22s-6
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-74
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, HYDRAULIC LASH
ADJUSTER...........................9-34
NOISE SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO.................8A-11
NOISE SUPPRESSION COMPONENTS -
OPERATION, RADIO..................8A-12
NON-ABS JUNCTION BLOCK -
DESCRIPTION...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
INSTALLATION
...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
OPERATION
.....................5-33,5s-32
NON-ABS JUNCTION BLOCK - REMOVAL
. . 5-33,
5s-32
NON-MONITORED CIRCUITS -
OPERATION
..........................25-5
NOT FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES
......................25-16
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION
....................Intro.-9
NVLD - INSTALLATION, WITH
...........25-20
NVLD - REMOVAL, WITH
..............25-19
O2 SENSOR - DESCRIPTION
............14-32
O2 SENSOR - OPERATION
.............14-32
OBTAINING DIAGNOSTIC TROUBLE
CODES - STANDARD PROCEDURE
.......8E-15
OCCUPANT RESTRAINT CONTROLLER -
DESCRIPTION
........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
INSTALLATION
.......................8O-8OCCUPANT RESTRAINT CONTROLLER -
OPERATION..........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
REMOVAL...........................8O-8
OIL - DESCRIPTION, FLEXIBLE FUEL
ENGINE..............................0-3
OIL - DESCRIPTION, REFRIGERANT......24-92
OIL - DIESEL ENGINES - DESCRIPTION,
ENGINE..............................0-6
OIL - OPERATION, REFRIGERANT........24-92
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE.............9-137,9-53
OIL AND LUBRICANTS - DESCRIPTION,
ENGINE..............................0-1
OIL COOLER - DESCRIPTION,
TRANSMISSION.......................7-37
OIL COOLER - INSPECTION,
TRANSMISSION.......................7-37
OIL COOLER - INSTALLATION,
TRANSMISSION.......................7-37
OIL COOLER & LINES - DESCRIPTION....9-138
OIL COOLER & LINES - INSTALLATION . . . 9-138
OIL COOLER & LINES - OPERATION......9-138
OIL COOLER & LINES - REMOVAL.......9-138
OIL COOLER - REMOVAL,
TRANSMISSION.......................7-37
OIL COOLER LINES - INSTALLATION,
TRANSMISSION.......................7-38
OIL COOLER LINES - REMOVAL,
TRANSMISSION.......................7-38
OIL FILTER - DESCRIPTION.............9-53
OIL FILTER - INSTALLATION........9-139,9-53
OIL FILTER - REMOVAL............9-139,9-53
OIL FILTER ADAPTER - INSTALLATION....9-139
OIL FILTER ADAPTER - REMOVAL.......9-139
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE.........9-10,9-86
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..............9-8,9-82
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-93
OIL LEVEL CHECK - STANDARD
PROCEDURE, ENGINE.................9-137
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-53
OIL PAN - CLEANING.................9-140
OIL PAN - INSPECTION................9-140
OIL PAN - INSTALLATION..........9-140,9-54
OIL PAN - REMOVAL..............9-140,9-54
OIL PRESSURE - DIAGNOSIS AND
TESTING, CHECKING ENGINE............9-52
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE....................9-136
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-141
OIL PRESSURE RELIEF VALVE -
REMOVAL..........................9-141
OIL PRESSURE SWITCH - DESCRIPTION . . 9-141
OIL PRESSURE SWITCH - INSTALLATION . 9-141,
9-54
OIL PRESSURE SWITCH - OPERATION....9-141
OIL PRESSURE SWITCH - REMOVAL . 9-141,9-54
OIL PUMP - ASSEMBLY...........9-143,9-56
OIL PUMP - ASSEMBLY.......21-232,21s-132
OIL PUMP - CLEANING............9-142,9-56
OIL PUMP - DESCRIPTION.............9-142
OIL PUMP - DESCRIPTION.....21-230,21s-131
OIL PUMP - DISASSEMBLY........9-142,9-55
OIL PUMP - DISASSEMBLY.....21-230,21s-131
OIL PUMP - INSPECTION..........9-142,9-56
OIL PUMP - INSTALLATION........9-144,9-57
OIL PUMP - INSTALLATION, SEAL......21-233,
21s-133
OIL PUMP - OPERATION.......21-230,21s-131
OIL PUMP - REMOVAL............9-142,9-55
OIL PUMP - REMOVAL, SEAL . . . 21-232,21s-133
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT...................9-127,9-40
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT
...................9-127,9-40
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
...................9-129,9-42
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT
...................9-128,9-41
OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR
..................9-129
OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR
..................9-129OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-28
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-27
ON-BOARD DIAGNOSTIC SYSTEM -
DIAGNOSIS AND TESTING..............8F-21
OPEN LATCH - INSTALLATION, HOLD.....23-25
OPEN LATCH - REMOVAL, HOLD........23-25
OPEN LATCH CABLE - INSTALLATION,
HOLD..............................23-38
OPEN LATCH CABLE - REMOVAL, HOLD . . . 23-38
OPEN LATCH STRIKER - INSTALLATION,
HOLD..............................23-26
OPEN LATCH STRIKER - REMOVAL,
HOLD..............................23-26
OPEN SWITCH - DESCRIPTION, FULL....8N-12,
8N-31
OPEN SWITCH - INSTALLATION, FULL....8N-13
OPEN SWITCH - OPERATION, FULL . 8N-12,8N-31
OPEN SWITCH - REMOVAL, FULL.......8N-13
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-13
OPENING DIMENSIONS -
SPECIFICATIONS, BODY..............23-127
OPENING REINFORCEMENT -
INSTALLATION, GRILLE................23-54
OPENING REINFORCEMENT - REMOVAL,
GRILLE............................23-54
ORDER, SPECIFICATIONS - FIRING........8I-3
O-RING - INSTALLATION, REAR COVER . . . 21-20
O-RING - REMOVAL, REAR COVER.......21-19
ORVR - OPERATION..................25-14
OUTBOARD - FRONT - INSTALLATION,
SEAT BELT & RETRACTOR.............8O-14
OUTBOARD - FRONT - REMOVAL, SEAT
BELT & RETRACTOR..................8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - FIRST ROW...........8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW - LEFT . . . 8O-17
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW -
RIGHT.............................8O-15
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - FIRST ROW.............8O-14
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - LEFT.....8O-17
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-15
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-16
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT & RETRACTOR -
SECOND ROW - RIGHT................8O-16
OUTER - INSTALLATION, CV BOOT........3-10
OUTER - REMOVAL, CV BOOT...........3-10
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-113
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-113
OUTER HALF SHAFT SEAL -
INSTALLATION.......................21-19
OUTER HALF SHAFT SEAL - REMOVAL . . . 21-19
OUTER TIE ROD - INSTALLATION........19-34
OUTER TIE ROD - REMOVAL...........19-34
OUTLET - DESCRIPTION, POWER......8W-97-4
OUTLET - DIAGNOSIS & TESTING,
POWER..........................8W-97-4
OUTLET - INSTALLATION, DEMISTER
.....24-46
OUTLET - INSTALLATION, INSTRUMENT
PANEL
.............................24-46
OUTLET - OPERATION, POWER
.......8W-97-4
OUTLET - REMOVAL, DEMISTER
........24-45
OUTLET - REMOVAL, INSTRUMENT
PANEL
.............................24-45
OUTLETS - DESCRIPTION, AIR
.....24-44,24-56
OUTLETS - INSTALLATION, AIR
.........24-56
OUTLETS - INSTALLATION, CENTER
BEZEL
.............................24-45
OUTLETS - REMOVAL, AIR
.............24-56
OUTLETS - REMOVAL, CENTER BEZEL
....24-44
OUTPUT - DESCRIPTION, SPEED
SENSOR
....................21-241,21s-142
OUTPUT - INSTALLATION, SPEED
SENSOR
....................21-242,21s-143
OUTPUT - OPERATION, 5 VOLT SUPPLY -
PCM
...............................8E-15
RSINDEX23
Description Group-Page Description Group-Page Description Group-Page

SET SWITCH - REMOVAL, MEMORY.....8N-13,
8N-56
SETTING - STANDARD PROCEDURE,
PINION FACTOR................8E-15,8E-23
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-11
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHAFT - ASSEMBLY, INPUT........21-96,21s-5
SHAFT - ASSEMBLY, INTERMEDIATE....21-107,
21s-17
SHAFT - ASSEMBLY, ROCKER ARMS.....9-109,
9s-27
SHAFT - DESCRIPTION, INPUT.....21-93,21s-1
SHAFT - DESCRIPTION, INTERMEDIATE . 21-100,
21s-9
SHAFT - DESCRIPTION, PROPELLER......3-21
SHAFT - DESCRIPTION, SHIFT FORK....21-113
SHAFT - DIAGNOSIS AND TESTING,
HALF............................3-1,3-13
SHAFT - DISASSEMBLY, INPUT.....21-93,21s-1
SHAFT - DISASSEMBLY, INTERMEDIATE . 21-100,
21s-10
SHAFT - DISASSEMBLY, ROCKER ARMS . . 9-109,
9s-27
SHAFT - FRONT - DESCRIPTION, HALF.....3-1
SHAFT - FRONT - INSTALLATION, HALF.....3-4
SHAFT - FRONT - REMOVAL, HALF........3-2
SHAFT - FRONT - SPECIFICATIONS, HALF . . 3-15,
3-6
SHAFT - INSTALLATION, PROPELLER......3-22
SHAFT - INSTALLATION, ROCKER ARMS . . 9-110,
9s-28
SHAFT - OPERATION, PROPELLER........3-21
SHAFT - REAR - DESCRIPTION, HALF.....3-13
SHAFT - REAR - INSTALLATION, HALF.....3-14
SHAFT - REAR - REMOVAL, HALF........3-13
SHAFT - REMOVAL, PROPELLER.........3-21
SHAFT - REMOVAL, ROCKER ARMS . 9-109,9s-27
SHAFT - RHD - INSTALLATION, PEDAL
TORQUE........................5-39,5s-43
SHAFT - RHD - REMOVAL, PEDAL
TORQUE........................5-39,5s-42
SHAFT - SPECIFICATIONS, PROPELLER....3-22
SHAFT COVER SEAL - INSTALLATION,
INPUT.............................21-14
SHAFT COVER SEAL - REMOVAL, INPUT . . 21-13
SHAFT END SEAL - INSTALLATION,
INPUT.............................21-16
SHAFT END SEAL - REMOVAL, INPUT....21-15
SHAFT INNER SEAL - INSTALLATION,
HALF..............................21-12
SHAFT INNER SEAL - REMOVAL, HALF . . . 21-12
SHAFT SEAL - INSTALLATION, INPUT.....21-18
SHAFT SEAL - INSTALLATION, OUTER
HALF..............................21-19
SHAFT SEAL - REMOVAL, INPUT........21-17
SHAFT SEAL - REMOVAL, OUTER HALF . . . 21-19
SHAFTS AND CARRIER ASSEMBLY -
DESCRIPTION, BALANCE................9-69
SHAFTS AND CARRIER ASSEMBLY -
INSTALLATION, BALANCE...............9-72
SHAFTS AND CARRIER ASSEMBLY -
OPERATION, BALANCE.................9-69
SHAFTS AND CARRIER ASSEMBLY -
REMOVAL, BALANCE...................9-69
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH................23-55
SHIELD - NO CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT
SIDE..............................23-97
SHIELD - NO CUPHOLDER - REMOVAL,
QUAD BUCKET SEAT SIDE.............23-97
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-55
SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT SIDE............23-107
SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT SIDE
..................23-107
SHIELD/CUPHOLDER - INSTALLATION,
QUAD BUCKET SEAT SIDE
.............23-96
SHIELD/CUPHOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE
...................23-96
SHIELDS - DESCRIPTION, HEAT
..........11-6
SHIELDS - INSTALLATION, HEAT
.........11-7SHIELDS - OPERATION, HEAT............11-7
SHIELDS - REMOVAL, HEAT.............11-7
SHIFT CABLE - INSTALLATION, GEAR....21-205
SHIFT CABLE - REMOVAL, GEAR.......21-204,
21s-105
SHIFT COVER - DESCRIPTION.........21-113
SHIFT FORK AND SHAFT - DESCRIPTION . 21-113
SHIFT INTERLOCK SOLENOID -
DESCRIPTION...............21-233,21s-133
SHIFT INTERLOCK SOLENOID -
DIAGNOSIS AND TESTING, BRAKE/
TRANSMISSION..............21-235,21s-135
SHIFT INTERLOCK SOLENOID -
INSTALLATION...............21-236,21s-136
SHIFT INTERLOCK SOLENOID -
OPERATION.................21-233,21s-134
SHIFT INTERLOCK SOLENOID -
REMOVAL..................21-235,21s-135
SHIFT LEVER - INSTALLATION, GEAR.....19-21
SHIFT LEVER - REMOVAL, GEAR........19-21
SHIM SELECTION, ADJUSTMENTS -
OUTPUT FLANGE......................21-7
SHOCK ABSORBER - DESCRIPTION.......2-37
SHOCK ABSORBER - INSTALLATION......2-38
SHOCK ABSORBER - OPERATION.........2-37
SHOCK ABSORBER - REMOVAL..........2-37
SHOCK ABSORBER (UPPER BUSHING) -
ASSEMBLY..........................2-38
SHOCK ABSORBER (UPPER BUSHING) -
DISASSEMBLY........................2-37
SHOE LINING - INSPECTION, REAR
DRUM BRAKE...................5-22,5s-21
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-73,
5s-76
SHOES - ADJUSTMENT, REAR DRUM
BRAKE.........................5-23,5s-22
SHOES - CLEANING, DISC BRAKE....5-16,5-18,
5s-15,5s-17
SHOES - INSPECTION, DISC BRAKE . . 5-16,5-18,
5s-15,5s-17
SHOES - INSTALLATION, REAR DISC
BRAKE.........................5-19,5s-18
SHOES - INSTALLATION, REAR DRUM
BRAKE.........................5-22,5s-21
SHOES - PARKING BRAKE -
INSTALLATION...................5-72,5s-75
SHOES - PARKING BRAKE - REMOVAL....5-67,
5s-69
SHOES - REMOVAL, REAR DISC BRAKE . . . 5-17,
5s-16
SHOES - REMOVAL, REAR DRUM BRAKE . . 5-19,
5s-18
SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5s-15
SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL, FRONT DISC BRAKE.........5s-14
SHOES (DISC/DISC BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-16
SHOES (DISC/DISC BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-14
SHOES (DISC/DRUM BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-17
SHOES (DISC/DRUM BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-15
SHOES (TRW BRAKES) - INSTALLATION,
FRONT DISC BRAKE..................5s-16
SHOES (TRW BRAKES) - REMOVAL,
FRONT DISC BRAKE
..................5s-14
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
..........................8W-01-10
SHROUD - LOWER - INSTALLATION
......19-22
SHROUD - LOWER - REMOVAL
.........19-21
SHROUD - UPPER - INSTALLATION
......19-23
SHROUD - UPPER - REMOVAL
..........19-23
SHUT DOWN RELAY - DESCRIPTION,
AUTO
...............................8I-3
SHUT DOWN RELAY - OPERATION, AUTO
. . . 8I-3
SIDE - INSTALLATION, LIFTGATE
........23-44
SIDE - REMOVAL, LIFTGATE
............23-44
SIDE COVER - INSTALLATION, FRONT
SEAT CUSHION
......................23-94
SIDE COVER - REMOVAL, FRONT SEAT
CUSHION
...........................23-94SIDE GEAR END PLAY - ADJUSTMENT,
DIFFERENTIAL.......................21-70
SIDE MOLDINGS - INSTALLATION, BODY . . 23-46
SIDE MOLDINGS - REMOVAL, BODY.....23-45
SIDE SHIELD - NO CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-97
SIDE SHIELD - NO CUPHOLDER -
REMOVAL, QUAD BUCKET SEAT.........23-97
SIDE SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT.................23-107
SIDE SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT......................23-107
SIDE SHIELD/CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-96
SIDE SHIELD/CUPHOLDER - REMOVAL,
QUAD BUCKET SEAT..................23-96
SIDE VIEW MIRROR - INSTALLATION.....23-59
SIDE VIEW MIRROR - REMOVAL........23-59
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-59
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-59
SIDEVIEW MIRROR - REMOVAL.........8N-49
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-18
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-18
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-17
SIGNAL SYSTEM - OPERATION, TURN....8L-18
SILL PLATE - INSTALLATION, LIFTGATE . . . 23-79
SILL PLATE - INSTALLATION, SLIDING
DOOR.............................23-82
SILL PLATE - REMOVAL, LIFTGATE.......23-79
SILL PLATE - REMOVAL, SLIDING DOOR . . 23-82
SILL TRIM PLATE - INSTALLATION,
DOOR.............................23-77
SILL TRIM PLATE - REMOVAL, DOOR....23-77
SINGLE ZONE - DESCRIPTION...........24-2
SINGLE ZONE - OPERATION.............24-4
SLAVE CYLINDER - INSTALLATION........6-11
SLAVE CYLINDER - REMOVAL...........6-11
SLEEVE - INSTALLATION, HEADREST.....23-90
SLEEVE - REMOVAL, HEADREST........23-90
SLIDING DOOR - INSTALLATION.........23-30
SLIDING DOOR - REMOVAL............23-29
SLIDING DOOR ADJUSTMENT -
STANDARD PROCEDURE..............8N-28
SLIDING DOOR ADJUSTMENTS,
ADJUSTMENTS......................23-30
SLIDING DOOR CONTROL MODULE -
DESCRIPTION.......................8E-19
SLIDING DOOR CONTROL MODULE -
INSTALLATION.......................8E-20
SLIDING DOOR CONTROL MODULE -
OPERATION.........................8E-19
SLIDING DOOR CONTROL MODULE -
REMOVAL..........................8E-19
SLIDING DOOR GLASS - INSTALLATION . . 23-110
SLIDING DOOR GLASS - REMOVAL.....23-110
SLIDING DOOR LOCK MOTOR -
INSTALLATION..................8N-44,8N-6
SLIDING DOOR LOCK MOTOR -
REMOVAL......................8N-44,8N-6
SLIDING DOOR MOTOR - DESCRIPTION . . 8N-30
SLIDING DOOR MOTOR - INSTALLATION . . 8N-31
SLIDING DOOR MOTOR - OPERATION....8N-30
SLIDING DOOR MOTOR - REMOVAL
.....8N-30
SLIDING DOOR SILL PLATE -
INSTALLATION
.......................23-82
SLIDING DOOR SILL PLATE - REMOVAL
. . 23-82
SLIDING DOOR STOP BUMPER BEZEL -
INSTALLATION
.......................23-25
SLIDING DOOR STOP BUMPER BEZEL -
REMOVAL
..........................23-25
SLIDING DOOR SYSTEM - DESCRIPTION,
POWER
............................8N-19
SLIDING DOOR SYSTEM - DIAGNOSIS
AND TESTING, POWER
................8N-22
SLIDING DOOR SYSTEM - OPERATION,
POWER
............................8N-21
SLIDING DOOR WEATHERSTRIP -
INSTALLATION
......................23-115
SLIDING DOOR WEATHERSTRIP -
REMOVAL
.........................23-115
SOCKET - INSTALLATION, STABILIZER
....23-33
SOCKET - REMOVAL, STABILIZER
.......23-33
SOLENOID - DESCRIPTION, EVAP/PURGE
. 25-12
32 INDEXRS
Description Group-Page Description Group-Page Description Group-Page