2004 CHRYSLER VOYAGER fuse

DISTRIBUTION DUCT
REMOVAL
(1) Remove the trim from the right quarter inner
panel and the right D pillaR (Refer to 23 - BODY/IN-
TERIOR/RIGHT QUARTER TRIM PANEL -
REMOVAL).
(2) Slide the rear distribution duct upwards far
enough to disengage it from the outlet at the top of
the rear HVAC housing (Fig. 2).
(3) While pulling the lower end of the rear distri-
bution duct away from the rear HVAC housing out-
let, disengage the upper end of the distribution duct
from the headliner duct.
(4) Remove the rea distribution duct from the
vehicle.
INSTALLATION
(1) Align the upper end of the rear distribution
duct to the headliner duct.
(2) Slide the upper end of the rear distribution
duct onto the headliner duct far enough to align the
lower end of the duct with the outlet at the top of the
rear HVAC housing.
(3) Slide the rear distribution duct downwards far
enough to engage it onto the outlet at the top of the
rear HVAC housing.
(4) Reinstall the trim onto the right quarter inner
panel and the right D pillar (Refer to 23 - BODY/IN-
TERIOR/RIGHT QUARTER TRIM PANEL -
INSTALLATION).
BLOWER MOTOR
DESCRIPTION
The blower motor is a 12-volt, Direct Current (DC)
motor with a squirrel cage-type blower wheel that is
secured to the blower motor shaft. The blower motor
and wheel are located near the top of the rear HVAC
housing in the passenger compartment behind the
right rear wheel house. The rear HVAC housing must
be removed from the vehicle to access the blower
motor for service. The blower motor and blower
motor wheel are a factory balanced unit and cannot
be adjusted or repaired. If faulty or damaged, the
blower motor and blower wheel must be replaced as
a unit.
OPERATION
On models equipped with the Manual Temperature
Control (MTC) system, the rear blower motor will
operate only whenever the ignition switch is in the
On position, the front blower control switch is in any
position except Off and the rear blower control switch
on the front A/C-heater control is in any position
except Off. On models equipped with the Automatic
Temperature Control (ATC) system, the blower motor
will operate whenever the ignition switch is in the
On position, the A/C-heater control power is turned
on and the rear blower control switch on the front
A/C-heater control is in any position except Off. The
rear blower motor can only be turned off by turning
off the rear system at the front A/C-heater control.
The rear blower motor receives battery current
whenever the rear blower motor relay is energized.
The rear blower motor relay output circuit is pro-
tected by a fuse in the Integrated Power Module
(IPM) located in the engine compartment near the
battery. In the MTC system, the rear blower motor
speed is controlled by regulating the path to ground
through the blower control switch and the blower
motor resistor. In the ATC system, the rear blower
motor speed is controlled by an electronic blower
motor power module, which uses a pulse width mod-
ulated input from the ATC control module and feed-
back from the rear blower motor to regulate the
blower motor ground path it provides. The rear
blower motor and wheel are used to control the veloc-
ity of air moving through the rear HVAC housing.
The rear blower motor controls the velocity of the air
flowing through the rear HVAC housing by spinning
the blower wheel within the housing at the selected
speed or, in the ATC system, at the selected or pro-
grammed speed.
Fig. 2 Rear Distribution Duct
1 - HEADLINER DUCT
2 - REAR DISTRIBUTION DUCT
3 - REAR HVAC HOUSING OUTLET
RSDISTRIBUTION - REAR24-57

DIAGNOSIS AND TESTING - REAR BLOWER
MOTOR
BLOWER MOTOR INOPERATIVE
For circuit descriptions and diagrams, refer to the
appropriate wiring information. The wiring informa-
tion includes wiring, diagrams, proper wire and con-
nector repair procedures, further details on wire
harness routing and retention, as well as pin-out and
location views for the various wire harness connec-
tors, splices and grounds.
BLOWER MOTOR ELECTRICAL DIAGNOSIS
(1) Check the fuse (Fuse 12 - 25 ampere) in the
Integrated Power Module (IPM). If OK, go to Step 2.
If not OK, repair the shorted circuit or component as
required and replace the faulty fuse.
(2) Turn the ignition switch to the On position. Be
certain that the rear A/C-heater control power is
turned on. Check for battery voltage at the fuse
(Fuse 12 - 25 ampere) in the IPM. If OK, go to Step
3. If not OK, check the rear blower motor relay.
(3) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Disconnect the rear HVAC wire harness connector
from the rear blower motor resistor block (Manual
Temperature Control) or the rear blower motor power
module (Automatic Temperature Control). Reconnect
the battery negative cable. Turn the ignition switch
to the On position. Be certain that the rear A/C-
heater control power is turned on. Check for battery
voltage at the fused rear blower motor relay output
circuit cavity of the rear HVAC wire harness connec-
tor for the rear blower motor resistor block (MTC) or
the rear blower motor power module (ATC). If OK, go
to Step 4. If not OK, repair the open fused front
blower motor relay output circuit to the IPM as
required.
(4) Turn the ignition switch to the Off position.
Disconnect and isolate the battery negative cable.
Disconnect the rear blower motor pigtail wire connec-
tor from the rear HVAC wire harness (MTC) or the
rear blower power module (ATC). Use jumper wires
to connect a battery and ground feeds to the blower
motor pigtail wire connector. The rear blower motor
should operate. If OK with MTC, proceed to diagno-
sis of the rear blower motor resistor block (Refer to
24 - HEATING & AIR CONDITIONING/CONTROLS
- REAR/BLOWER MOTOR RESISTOR - DIAGNOSIS
AND TESTING). If OK with ATC, use a DRBIII scan
tool to diagnose the rear blower motor power module.
Refer to the appropriate diagnostic information. If
not OK with MTC or ATC, replace the faulty rear
blower motor.BLOWER MOTOR NOISE OR VIBRATION
Refer to the Blower Motor Noise/Vibration Diagno-
sis chart for basic checks of the blower motor when a
vibration or noise is present (Fig. 3).
REMOVAL
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
WARNING) and (Refer to 24 - HEATING & AIR CON-
DITIONING/PLUMBING - CAUTION).
(1) Remove the rear HVAC housing from the vehi-
cle (Refer to 24 - HEATING & AIR CONDITIONING/
DISTRIBUTION/HVAC HOUSING - REMOVAL).
(2) Disconnect the rear blower motor pigtail wire
connector.
NOTE: With the Manual Temperature Control sys-
tem, the blower motor pigtail wire is connected to a
take out and connector of the rear HVAC wire har-
ness. With the Automatic Temperature Control sys-
tem , the blower pigtail wire is connected to a
receptacle on the blower motor power module.
(3) Remove the three screws that secure the rear
blower motor to the outboard side of the rear HVAC
housing (Fig. 4).
(4) Remove the rear blower motor from the rear
HVAC housing.
INSTALLATION
(1) Position the rear blower motor into the rear
HVAC housing.
(2) Install the three screws that secure the blower
motor to the rear HVAC housing. Tighten the screws
to 2 N´m (17 in. lbs.).
(3) Reconnect the rear blower motor pigtail wire
connector.
NOTE: With the Manual Temperature Control system
, the blower pigtail wire is connected to a take out
and connector of the rear HVAC wire harness. With
the Automatic Temperature Control system, the
blower pigtail wire is connected to a receptacle on
the blower motor power module.
24 - 58 DISTRIBUTION - REARRS
BLOWER MOTOR (Continued)

FRONT DISC BRAKE SHOES
(CONTINENTAL TEVES BRAKES) -
INSTALLATION.......................5s-15
FRONT DISC BRAKE SHOES
(CONTINENTAL TEVES BRAKES) -
REMOVAL..........................5s-14
FRONT DISC BRAKE SHOES (DISC/DISC
BRAKES) - INSTALLATION...............5-16
FRONT DISC BRAKE SHOES (DISC/DISC
BRAKES) - REMOVAL..................5-14
FRONT DISC BRAKE SHOES (DISC/
DRUM BRAKES) - INSTALLATION.........5-17
FRONT DISC BRAKE SHOES (DISC/
DRUM BRAKES) - REMOVAL............5-15
FRONT DISC BRAKE SHOES (TRW
BRAKES) - INSTALLATION..............5s-16
FRONT DISC BRAKE SHOES (TRW
BRAKES) - REMOVAL.................5s-14
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION.......23-113
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL...........23-113
FRONT DOOR INNER BELT MOLDING -
INSTALLATION......................23-115
FRONT DOOR INNER BELT MOLDING -
REMOVAL.........................23-115
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION......................23-113
FRONT DOOR OUTER BELT MOLDING -
REMOVAL.........................23-113
FRONT DOOR WEATHERSTRIP -
INSTALLATION......................23-114
FRONT DOOR WEATHERSTRIP -
REMOVAL.........................23-114
FRONT FASCIA - INSTALLATION..........13-1
FRONT FASCIA - REMOVAL..............13-1
FRONT FENDER - INSTALLATION........23-52
FRONT FENDER - REMOVAL............23-52
FRONT FOG LAMP - DIAGNOSIS AND
TESTING............................8L-7
FRONT FOG LAMP - INSTALLATION.......8L-8
FRONT FOG LAMP - REMOVAL...........8L-8
FRONT FOG LAMP UNIT ALIGNMENT -
EXPORT - STANDARD PROCEDURE.......8L-9
FRONT FOG LAMP UNIT ALIGNMENT -
STANDARD PROCEDURE................8L-9
FRONT INBOARD - INSTALLATION, SEAT
BELT BUCKLE.......................8O-12
FRONT INBOARD - REMOVAL, SEAT
BELT BUCKLE.......................8O-12
FRONT MOUNT - INSTALLATION....9-131,9-49
FRONT MOUNT - REMOVAL........9-131,9-49
FRONT SEAT - INSTALLATION...........23-91
FRONT SEAT - REMOVAL..............23-91
FRONT SEAT BACK - INSTALLATION......23-92
FRONT SEAT BACK - REMOVAL.........23-92
FRONT SEAT CUSHION SIDE COVER -
INSTALLATION.......................23-94
FRONT SEAT CUSHION SIDE COVER -
REMOVAL..........................23-94
FRONT SEAT RISER - MANUAL TRACK -
INSTALLATION.......................23-95
FRONT SEAT RISER - MANUAL TRACK -
REMOVAL..........................23-94
FRONT SEAT TRACK - REAR COVER -
INSTALLATION.......................23-96
FRONT SEAT TRACK - REAR COVER -
REMOVAL..........................23-96
FRONT SEAT TRACK MANUAL
ADJUSTER - INSTALLATION............23-95
FRONT SEAT TRACK MANUAL
ADJUSTER - REMOVAL................23-95
FRONT SEAT TRACK POWER ADJUSTER
- INSTALLATION.....................23-95
FRONT SEAT TRACK POWER ADJUSTER
- REMOVAL.........................23-95
FRONT SEATBACK ASSIST STRAP -
INSTALLATION.......................23-92
FRONT SEATBACK ASSIST STRAP -
REMOVAL..........................23-92
FRONT SEATBACK COVER -
INSTALLATION.......................23-93
FRONT SEATBACK COVER - REMOVAL
....23-93
FRONT SEATBACK PANEL -
INSTALLATION
.......................23-93
FRONT SEATBACK PANEL - REMOVAL
....23-92
FRONT SUSPENSION - DESCRIPTION
......2-2
FRONT SUSPENSION - OPERATION
........2-2FRONT SUSPENSION FASTENER
TORQUE, SPECIFICATIONS...............2-3
FRONT SUSPENSION, SPECIAL TOOLS.....2-3
FRONT WASHER PUMP MOTOR -
INSTALLATION.......................8R-8
FRONT WASHER PUMP MOTOR -
REMOVAL...........................8R-8
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-80
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-79
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-55
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-55
FRONT WIPER ARM ALIGNMENT -
STANDARD PROCEDURE...............8R-8
FRONT WIPER ARMS - INSTALLATION....8R-9
FRONT WIPER ARMS - REMOVAL........8R-9
FRONT WIPER MOTOR - INSTALLATION . . . 8R-9
FRONT WIPER MOTOR - REMOVAL.......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS
AND TESTING........................8R-2
FRONT WIPER/WASHER SWITCH -
DIAGNOSIS AND TESTING..............8R-2
FRONT/QUAD SEAT CUSHION -
INSTALLATION.......................23-93
FRONT/QUAD SEAT CUSHION -
REMOVAL..........................23-93
FRONT-WHEEL-DRIVE - INSTALLATION....2-36
FRONT-WHEEL-DRIVE - REMOVAL........2-36
FUEL CORRECTION OR ADAPTIVE
MEMORIES, OPERATION...............14-20
FUEL DELIVERY - DESCRIPTION..........14-2
FUEL DELIVERY - OPERATION...........14-2
FUEL DELIVERY SYSTEM - DIAGNOSIS
AND TESTING........................14-2
FUEL DOSING PUMP - DESCRIPTION....24-115
FUEL DOSING PUMP - INSTALLATION . . . 24-116
FUEL DOSING PUMP - OPERATION.....24-115
FUEL DOSING PUMP - REMOVAL.......24-115
FUEL ENGINE OIL - DESCRIPTION,
FLEXIBLE.............................0-3
FUEL FILL DOOR - INSTALLATION.......23-52
FUEL FILL DOOR - REMOVAL...........23-52
FUEL FILL DOOR BLOCKER LATCH -
INSTALLATION.......................23-53
FUEL FILL DOOR BLOCKER LATCH -
REMOVAL..........................23-53
FUEL FILL DOOR BLOCKER LATCH
STRIKER - INSTALLATION..............23-53
FUEL FILL DOOR BLOCKER LATCH
STRIKER - REMOVAL.................23-53
FUEL FILL DOOR BLOCKER LOCKOUT
LINK - INSTALLATION.................23-54
FUEL FILL DOOR BLOCKER LOCKOUT
LINK - REMOVAL.....................23-53
FUEL FILLER CAP - DESCRIPTION.......25-12
FUEL FILLER CAP - OPERATION.........25-12
FUEL INJECTOR - DESCRIPTION.........14-26
FUEL INJECTOR - OPERATION..........14-26
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION........................14-5
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION........................14-5
FUEL LEVEL SENDING UNIT / SENSOR -
OPERATION..........................14-5
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL...........................14-5
FUEL LINE - INSTALLATION...........24-118
FUEL LINE - REMOVAL...............24-117
FUEL LINES/HOSES AND CLAMPS -
DESCRIPTION........................14-6
FUEL PRESSURE REGULATOR -
INSTALLATION........................14-7
FUEL PRESSURE REGULATOR -
OPERATION..........................14-7
FUEL PRESSURE REGULATOR -
REMOVAL...........................14-7
FUEL PUMP - DESCRIPTION.............14-8
FUEL PUMP - OPERATION..............14-8
FUEL PUMP MODULE - DESCRIPTION.....14-8
FUEL PUMP MODULE - INSTALLATION....14-9
FUEL PUMP MODULE - OPERATION
.......14-8
FUEL PUMP MODULE - REMOVAL
........14-8
FUEL PUMP RELAY - DESCRIPTION
......14-28
FUEL PUMP RELAY - OPERATION
........14-28
FUEL REQUIREMENTS - DESCRIPTION
......0-4FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION........................0-6
FUEL, SPECIAL TOOLS............14-23,14-4
FUEL SYSTEM PRESSURE RELEASE
PROCEDURE - STANDARD
PROCEDURE.........................14-2
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-3
FUEL TANK - DESCRIPTION............14-10
FUEL TANK - INSTALLATION............14-12
FUEL TANK - OPERATION..............14-11
FUEL TANK - REMOVAL...............14-11
FUEL TANK - STANDARD PROCEDURE,
DRAINING...........................14-2
FUEL TANK FILLER TUBE -
INSTALLATION.......................14-13
FUEL TANK FILLER TUBE - REMOVAL....14-12
FULL OPEN SWITCH - DESCRIPTION....8N-12,
8N-31
FULL OPEN SWITCH - INSTALLATION....8N-13
FULL OPEN SWITCH - OPERATION . 8N-12,8N-31
FULL OPEN SWITCH - REMOVAL........8N-13
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-3
FUSE - OPERATION, IOD.............8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON......8W-01-10
FWD - INSTALLATION..................2-45
FWD - INSTALLATION, REAR WHEEL
SPEED SENSOR.......................5-81
FWD - INSTALLATION, SPRING...........2-42
FWD - REMOVAL......................2-45
FWD - REMOVAL, REAR WHEEL SPEED
SENSOR............................5-81
FWD - REMOVAL, SPRING..............2-41
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL . 9-10,9-86
GAP AND FLUSH MEASUREMENTS -
SPECIFICATIONS....................23-124
GAP, SPECIFICATIONS - WHEEL SPEED
SENSOR AIR.........................5-79
GAS - INSTALLATION, MODULAR
CLUTCH ASSY - 2.4L..................6-11
GAS - REMOVAL, MODULAR CLUTCH
ASSY - 2.4L..........................6-11
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD.............9-24,9-99,9s-16
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE....9-11,9-85
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE.......9-11,9-84
GASOLINE ENGINES - DIAGNOSIS AND
TESTING, SYSTEM CHARGE LEVEL
TEST..............................24-67
GEAR - DESCRIPTION.................19-26
GEAR - INSTALLATION, LHD............19-32
GEAR - INSTALLATION, RHD............19-33
GEAR & LINK ROD - DESCRIPTION, LIFT . 8N-16
GEAR & LINK ROD - INSTALLATION,
LIFT...............................8N-16
GEAR & LINK ROD - OPERATION, LIFT . . . 8N-16
GEAR & LINK ROD - REMOVAL, LIFT.....8N-16
GEAR - OPERATION...................19-27
GEAR - REMOVAL, LHD...............19-27
GEAR - REMOVAL, RHD...............19-31
GEAR END PLAY - ADJUSTMENT,
DIFFERENTIAL SIDE..................21-70
GEAR SHIFT CABLE - INSTALLATION....21-205
GEAR SHIFT CABLE - REMOVAL . 21-204,21s-105
GEAR SHIFT LEVER - INSTALLATION.....19-21
GEAR SHIFT LEVER - REMOVAL.........19-21
GEAR, SPECIAL TOOLS - POWER
STEERING..........................19-34
GEARSHIFT BOOT - INSTALLATION......21-73
GEARSHIFT BOOT - REMOVAL..........21-72
GEARSHIFT CABLE - CROSSOVER -
INSTALLATION.......................21-76
GEARSHIFT CABLE - CROSSOVER -
REMOVAL..........................21-73
GEARSHIFT CABLE - SELECTOR -
INSTALLATION
.......................21-84
GEARSHIFT CABLE - SELECTOR -
REMOVAL
..........................21-81
GEARSHIFT CABLE ADJUSTMENT,
ADJUSTMENTS
.....................21-206
GEARSHIFT KNOB - INSTALLATION
......21-87
GEARSHIFT KNOB - REMOVAL
..........21-87
RSINDEX15
Description Group-Page Description Group-Page Description Group-Page

GEARSHIFT MECHANISM -
INSTALLATION.......................21-89
GEARSHIFT MECHANISM - REMOVAL....21-87
GEARTRAIN - DESCRIPTION,
PLANETARY.................21-232,21s-132
GEARTRAIN - OPERATION, PLANETARY . 21-232,
21s-132
GENERAL - WARNINGS.............8W-01-7
GENERAL DIAGNOSIS - DIAGNOSIS AND
TESTING, 41TE TRANSAXLE...........21-119
GENERAL DIAGNOSIS - DIAGNOSIS AND
TESTING, 4XTE TRANSAXLE...........21s-27
GENERATOR - DESCRIPTION...........8F-23
GENERATOR - OPERATION.............8F-23
GENERATOR DECOUPLER PULLEY -
DESCRIPTION..................8F-25,8F-27
GENERATOR DECOUPLER PULLEY -
DIAGNOSIS AND TESTING.........8F-25,8F-27
GENERATOR DECOUPLER PULLEY -
INSTALLATION..................8F-26,8F-28
GENERATOR DECOUPLER PULLEY -
OPERATION....................8F-25,8F-27
GENERATOR DECOUPLER PULLEY -
REMOVAL.....................8F-26,8F-28
GENERATOR, SPECIFICATIONS..........8F-22
GLASS - DESCRIPTION, HEATED.........8G-1
GLASS - INSTALLATION, DOOR.........23-17
GLASS - INSTALLATION, REAR DOOR . . . 23-111
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-59
GLASS - INSTALLATION, SLIDING DOOR . . . 23-110
GLASS - OPERATION, HEATED...........8G-2
GLASS - REMOVAL, DOOR.............23-17
GLASS - REMOVAL, REAR DOOR.......23-111
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-59
GLASS - REMOVAL, SLIDING DOOR.....23-110
GLASS INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER...............8A-9
GLASS INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER.....8A-9
GLASS INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER.................8A-9
GLASS PANEL - INSTALLATION........23-120
GLASS PANEL - REMOVAL............23-120
GLASS PANEL ADJUSTMENT,
ADJUSTMENTS - SUNROOF...........23-120
GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-113
GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-113
GLOVE BOX - INSTALLATION...........23-64
GLOVE BOX - REMOVAL...............23-64
GLOVE BOX LAMP SWITCH -
INSTALLATION.......................8L-22
GLOVE BOX LAMP SWITCH - REMOVAL . . 8L-22
GLOVE BOX LATCH - INSTALLATION.....23-64
GLOVE BOX LATCH - REMOVAL.........23-64
GLOVE BOX LATCH STRIKER -
INSTALLATION.......................23-64
GLOVE BOX LATCH STRIKER - REMOVAL . 23-64
GRID LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE...............8G-4
GRILLE - INSTALLATION, COWL
.........23-51
GRILLE - REMOVAL, COWL
............23-50
GRILLE OPENING REINFORCEMENT -
INSTALLATION
.......................23-54
GRILLE OPENING REINFORCEMENT -
REMOVAL
..........................23-54
GROCERY BAG RETAINER -
INSTALLATION, PLASTIC
..............23-105
GROCERY BAG RETAINER - REMOVAL,
PLASTIC
..........................23-104
GROMMET REPLACEMENT - STANDARD
PROCEDURE, PUSH-PIN
...............8N-28
GROUND - OPERATION, PCM
...........8E-15
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO
..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR
..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO
.............................8W-01-10
GUIDE - INSTALLATION, UNDER SEAT
STORAGE BIN
......................23-105
GUIDE - REMOVAL, UNDER SEAT
STORAGE BIN
......................23-105GUIDE PIN BUSHINGS (CONTINENTAL
TEVES BRAKES) - ASSEMBLY, CALIPER . . . 5s-24
GUIDE PIN BUSHINGS (CONTINENTAL
TEVES BRAKES) - DISASSEMBLY,
CALIPER...........................5s-23
GUIDE PIN BUSHINGS (DISC/DISC
BRAKES) - ASSEMBLY, CALIPER..........5-25
GUIDE PIN BUSHINGS (DISC/DISC
BRAKES) - DISASSEMBLY, CALIPER.......5-24
GUIDE PINS (DISC/DRUM BRAKES) -
INSTALLATION, DISC BRAKE CALIPER.....5-31
GUIDE PINS (DISC/DRUM BRAKES) -
REMOVAL, DISC BRAKE CALIPER.........5-31
GUIDE PINS (TRW BRAKES) -
INSTALLATION, DISC BRAKE CALIPER....5s-30
GUIDE PINS (TRW BRAKES) - REMOVAL,
DISC BRAKE CALIPER.................5s-30
HALF SHAFT - DIAGNOSIS AND TESTING . . . 3-1,
3-13
HALF SHAFT - FRONT - DESCRIPTION......3-1
HALF SHAFT - FRONT - INSTALLATION.....3-4
HALF SHAFT - FRONT - REMOVAL.........3-2
HALF SHAFT - FRONT - SPECIFICATIONS . . 3-15,
3-6
HALF SHAFT - REAR - DESCRIPTION......3-13
HALF SHAFT - REAR - INSTALLATION.....3-14
HALF SHAFT - REAR - REMOVAL.........3-13
HALF SHAFT INNER SEAL -
INSTALLATION.......................21-12
HALF SHAFT INNER SEAL - REMOVAL....21-12
HALF SHAFT SEAL - INSTALLATION,
OUTER..............................21-19
HALF SHAFT SEAL - REMOVAL, OUTER . . . 21-19
HANDLE - INSTALLATION, ASSIST.......23-74
HANDLE - INSTALLATION, EXTERIOR....23-22,
23-40
HANDLE - INSTALLATION, INSIDE LATCH . . 23-34
HANDLE - INSTALLATION, OUTSIDE......23-35
HANDLE - INSTALLATION, RECLINER.....23-90
HANDLE - REMOVAL, ASSIST...........23-74
HANDLE - REMOVAL, EXTERIOR . . . 23-21,23-40
HANDLE - REMOVAL, INSIDE LATCH.....23-34
HANDLE - REMOVAL, OUTSIDE.........23-35
HANDLE - REMOVAL, RECLINER........23-90
HANDLE ACTUATOR - INSTALLATION,
INSIDE.............................23-27
HANDLE ACTUATOR - REMOVAL, INSIDE . . 23-27
HANDLE CABLE - INSTALLATION, INSIDE . . 23-38
HANDLE CABLE - INSTALLATION,
OUTSIDE...........................23-37
HANDLE CABLE - REMOVAL, INSIDE.....23-37
HANDLE CABLE - REMOVAL, OUTSIDE....23-37
HANDLE SWITCH - DESCRIPTION,
EXTERIOR..........................8N-11
HANDLE SWITCH - INSTALLATION,
EXTERIOR..........................8N-12
HANDLE SWITCH - OPERATION,
EXTERIOR..........................8N-11
HANDLE SWITCH - REMOVAL, EXTERIOR . 8N-11
HANDLING AIRBAGS - STANDARD
PROCEDURE.........................8O-3
HANDLING TUBING AND FITTINGS -
STANDARD PROCEDURE...............24-70
HARNESS - DESCRIPTION, WIRING......8N-35
HARNESS - DIAGNOSIS AND TESTING,
WIRING..........................8W-01-7
HARNESS - INSTALLATION, WIRING.....8N-36
HARNESS - OPERATION, WIRING
........8N-35
HARNESS - REMOVAL, WIRING
.........8N-35
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION
........................5-89
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION
..........................5-89
HEAD - CLEANING, CYLINDER
. 9-100,9-26,9s-17
HEAD - DESCRIPTION, CYLINDER
....9-24,9-99,
9s-16
HEAD - INSPECTION, CYLINDER
....9-101,9-26,
9s-17
HEAD - INSTALLATION, CYLINDER
. . 9-101,9-26,
9s-18
HEAD - REMOVAL, CYLINDER
. . 9-100,9-25,9s-17
HEAD COVER - CLEANING, CYLINDER
.....9-31
HEAD COVER - INSPECTION, CYLINDER
. . . 9-31
HEAD COVER - INSTALLATION,
CYLINDER
...........................9-31
HEAD COVER - LEFT - INSTALLATION,
CYLINDER
..........................9-103HEAD COVER - LEFT - REMOVAL,
CYLINDER..........................9-103
HEAD COVER - REMOVAL, CYLINDER.....9-31
HEAD COVER - RIGHT - INSTALLATION,
CYLINDER..........................9-103
HEAD COVER - RIGHT - REMOVAL,
CYLINDER..........................9-102
HEAD COVER-LEFT - INSTALLATION,
CYLINDER..........................9s-20
HEAD COVER-LEFT - REMOVAL,
CYLINDER..........................9s-20
HEAD COVER-RIGHT - INSTALLATION,
CYLINDER..........................9s-19
HEAD COVER-RIGHT - REMOVAL,
CYLINDER..........................9s-19
HEAD COVER(S) - DESCRIPTION,
CYLINDER.....................9-102,9s-19
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER..........9-24,9-99,9s-16
HEAD OFF - INSTALLATION, CYLINDER . . . 9-108,
9-33,9s-26
HEAD OFF - REMOVAL, CYLINDER . . 9-106,9-32,
9s-24
HEAD ON - INSTALLATION, CYLINDER . . . 9-108,
9-33,9s-26
HEAD ON - REMOVAL, CYLINDER . . . 9-106,9-32,
9s-24
HEADER TRIM - INSTALLATION, REAR....23-80
HEADER TRIM - REMOVAL, REAR.......23-80
HEADLAMP - DIAGNOSIS AND TESTING . . 8L-10
HEADLAMP - INSTALLATION............8L-12
HEADLAMP - REMOVAL.................8L-12
HEADLAMP SWITCH - DIAGNOSIS AND
TESTING...........................8L-12
HEADLAMP SWITCH - INSTALLATION....8L-13
HEADLAMP SWITCH - REMOVAL........8L-13
HEADLAMP UNIT - EXPORT -
INSTALLATION.......................8L-17
HEADLAMP UNIT - EXPORT - REMOVAL . . 8L-17
HEADLAMP UNIT ALIGNMENT - EXPORT
- STANDARD PROCEDURE.............8L-14
HEADLAMP UNIT ALIGNMENT -
STANDARD PROCEDURE...............8L-13
HEADLINER - INSTALLATION...........23-78
HEADLINER - REMOVAL...............23-78
HEADREST - INSTALLATION............23-89
HEADREST - REMOVAL................23-89
HEADREST SLEEVE - INSTALLATION.....23-90
HEADREST SLEEVE - REMOVAL.........23-90
HEAT DUCT - INSTALLATION, REAR
FLOOR.............................24-63
HEAT DUCT - REMOVAL, REAR FLOOR . . . 24-62
HEAT SHIELDS - DESCRIPTION..........11-6
HEAT SHIELDS - INSTALLATION..........11-7
HEAT SHIELDS - OPERATION............11-7
HEAT SHIELDS - REMOVAL.............11-7
HEAT STAKING - STANDARD
PROCEDURE........................23-10
HEATED GLASS - DESCRIPTION..........8G-1
HEATED GLASS - OPERATION...........8G-2
HEATED MIRRORS - DESCRIPTION.......8G-6
HEATED MIRRORS - OPERATION.........8G-6
HEATED SEAT ELEMENTS -
DESCRIPTION.......................8G-10
HEATED SEAT ELEMENTS - DIAGNOSIS
AND TESTING.......................8G-10
HEATED SEAT ELEMENTS -
INSTALLATION......................8G-11
HEATED SEAT ELEMENTS - OPERATION . . 8G-10
HEATED SEAT ELEMENTS - REMOVAL....8G-11
HEATED SEAT MODULE - DESCRIPTION....8E-8
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING........................8E-9
HEATED SEAT MODULE - INSTALLATION . . 8E-10
HEATED SEAT MODULE - OPERATION.....8E-9
HEATED SEAT MODULE - REMOVAL.......8E-9
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-12
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING.......................8G-12
HEATED SEAT SENSOR - OPERATION
....8G-12
HEATED SEAT SWITCH - DESCRIPTION,
DRIVER
.............................8G-8
HEATED SEAT SWITCH - DESCRIPTION,
PASSENGER
........................8G-12
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING, DRIVER
.................8G-9
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING, PASSENGER
............8G-13
16 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

INBOARD - 50/50 BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-13
INBOARD - INSTALLATION, SEAT BELT
BUCKLE - FRONT....................8O-12
INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE -
FIRST ROW.........................8O-12
INBOARD - QUAD BUCKET - REMOVAL,
SEAT BELT BUCKLE - FIRST ROW.......8O-12
INBOARD - REMOVAL, SEAT BELT
BUCKLE - FRONT....................8O-12
INDICATOR LAMP - DESCRIPTION,
VTSS/SKIS..........................8Q-7
INDICATOR LAMP - OPERATION,
VTSS/SKIS..........................8Q-8
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR..........22-16,22s-8
INFLATION PRESSURES - STANDARD
PROCEDURE, TIRE..............22-16,22s-8
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-6
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INFRARED TEMPERATURE SENSOR -
DESCRIPTION.......................24-29
INFRARED TEMPERATURE SENSOR -
OPERATION.........................24-29
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-37
INJECTION SYSTEM - OPERATION.......14-18
INJECTOR - DESCRIPTION, FUEL........14-26
INJECTOR - OPERATION, FUEL..........14-26
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-30
INLET FILTER - INSTALLATION..........14-13
INLET FILTER - REMOVAL..............14-13
INLET HOSE - INSTALLATION, HEATER....24-86
INLET HOSE - REMOVAL, HEATER.......24-85
INLET TUBE - 2.4L - DESCRIPTION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - INSTALLATION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - REMOVAL, WATER
PUMP..............................7-35
INLET TUBE - 3.3/3.8L - INSTALLATION,
WATER PUMP........................7-36
INLET TUBE - 3.3/3.8L - REMOVAL,
WATER PUMP........................7-36
INNER - INSTALLATION, CV BOOT.........3-6
INNER - REMOVAL, CV BOOT.............3-6
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-115
INNER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-115
INNER SEAL - INSTALLATION, HALF
SHAFT.............................21-12
INNER SEAL - REMOVAL, HALF SHAFT . . . 21-12
INNER/OUTER - INSTALLATION, CV
BOOT...............................3-17
INNER/OUTER - REMOVAL, CV BOOT......3-15
INPUT - DESCRIPTION, SPEED SENSOR . 21-239,
21s-140
INPUT - INSTALLATION, SPEED
SENSOR....................21-240,21s-141
INPUT - OPERATION, DATA BUS
COMMUNICATION RECEIVE - PCM.......8E-15
INPUT - OPERATION, IGNITION SENSE -
PCM...............................8E-15
INPUT - OPERATION, SENSOR RETURN -
PCM...............................8E-15
INPUT - OPERATION, SPEED SENSOR . . . 21-240,
21s-140
INPUT - REMOVAL, SPEED SENSOR....21-240,
21s-141
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-216,
21s-116
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY...............21-208,21s-107
INPUT FLANGE SEAL - INSTALLATION
.....3-45
INPUT FLANGE SEAL - REMOVAL
.........3-44
INPUT SHAFT - ASSEMBLY
........21-96,21s-5
INPUT SHAFT - DESCRIPTION
.....21-93,21s-1
INPUT SHAFT - DISASSEMBLY
.....21-93,21s-1INPUT SHAFT COVER SEAL -
INSTALLATION.......................21-14
INPUT SHAFT COVER SEAL - REMOVAL . . . 21-13
INPUT SHAFT END SEAL -
INSTALLATION.......................21-16
INPUT SHAFT END SEAL - REMOVAL.....21-15
INPUT SHAFT SEAL - INSTALLATION.....21-18
INPUT SHAFT SEAL - REMOVAL.........21-17
INSIDE HANDLE ACTUATOR -
INSTALLATION.......................23-27
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-27
INSIDE HANDLE CABLE - INSTALLATION . . 23-38
INSIDE HANDLE CABLE - REMOVAL......23-37
INSIDE LATCH HANDLE - INSTALLATION . . 23-34
INSIDE LATCH HANDLE - REMOVAL......23-34
INSPECT, INSPECTION...............21-114
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-1
INSTRUMENT CLUSTER - OPERATION.....8J-1
INSTRUMENT PANEL - INSTALLATION,
LOWER............................23-69
INSTRUMENT PANEL - REMOVAL,
LOWER............................23-69
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-9
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-8
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-66
INSTRUMENT PANEL ASSEMBLY -
REMOVAL............................23-65
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-68
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-68
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-55
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-55
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-55
INSTRUMENT PANEL DUCTS - REMOVAL . 24-55
INSTRUMENT PANEL END CAP -
INSTALLATION.......................23-68
INSTRUMENT PANEL END CAP -
REMOVAL..........................23-68
INSTRUMENT PANEL OUTLET -
INSTALLATION.......................24-46
INSTRUMENT PANEL OUTLET -
REMOVAL..........................24-45
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-69
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-68
INSTRUMENT PANEL TOP PAD
ASSEMBLY - INSTALLATION............23-72
INSTRUMENT PANEL TOP PAD
ASSEMBLY - REMOVAL................23-71
INTAKE MANIFOLD - DESCRIPTION . . 9-144,9-58
INTAKE MANIFOLD - INSTALLATION,
LOWER............................9-149
INTAKE MANIFOLD - INSTALLATION,
UPPER.............................9-147
INTAKE MANIFOLD - LOWER -
CLEANING..........................9-148
INTAKE MANIFOLD - LOWER -
INSPECTION....................9-148,9-60
INTAKE MANIFOLD - LOWER -
INSTALLATION........................9-60
INTAKE MANIFOLD - LOWER - REMOVAL . . 9-60
INTAKE MANIFOLD - REMOVAL, LOWER . . 9-148
INTAKE MANIFOLD - REMOVAL, UPPER . . . 9-145
INTAKE MANIFOLD - UPPER -
INSPECTION.........................9-59
INTAKE MANIFOLD - UPPER -
INSTALLATION........................9-59
INTAKE MANIFOLD - UPPER - REMOVAL . . . 9-58
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING...................9-145,9-58
INTAKE MANIFOLD VACUUM PORT
REPAIR - STANDARD PROCEDURE.......9-145
INTAKE PIPE - INSTALLATION, AIR
......24-114
INTAKE PIPE - REMOVAL, AIR
.........24-113
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.................9-105,9-32,9s-22
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
..............9-104,9-32,9s-21
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...................9-105,9s-22INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..................9-106,9s-23
INTAKE/EXHAUST VALVES & SEATS -
OPERATION....................9-104,9s-21
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.....................9-105,9s-22
INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER GLASS.........8A-9
INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER
GLASS..............................8A-9
INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER GLASS...........8A-9
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-2
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-3
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-2
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-2
INTERACTIVE SPEED CONTROL (4
SPEED EATX ONLY) - OPERATION........8P-2
INTERFACE (PCI) BUS, OPERATION -
PROGRAMMABLE COMMUNICATIONS....14-21
INTERIOR LAMPS, SPECIFICATIONS......8L-20
INTERLOCK - DESCRIPTION, IGNITION....19-17
INTERLOCK SOLENOID - DESCRIPTION,
SHIFT......................21-233,21s-133
INTERLOCK SOLENOID - DIAGNOSIS
AND TESTING, BRAKE/TRANSMISSION
SHIFT......................21-235,21s-135
INTERLOCK SOLENOID - INSTALLATION,
SHIFT.......................21-236,21s-136
INTERLOCK SOLENOID - OPERATION,
SHIFT......................21-233,21s-134
INTERLOCK SOLENOID - REMOVAL,
SHIFT......................21-235,21s-135
INTERLOCK SWITCH - INSTALLATION,
CLUTCH PEDAL.......................6-14
INTERLOCK SWITCH - REMOVAL,
CLUTCH PEDAL.......................6-13
INTERMEDIATE SHAFT - ASSEMBLY....21-107,
21s-17
INTERMEDIATE SHAFT - DESCRIPTION . . 21-100,
21s-9
INTERMEDIATE SHAFT - DISASSEMBLY . 21-100,
21s-10
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-5
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-3,9-76
IOD FUSE - DESCRIPTION...........8W-97-3
IOD FUSE - OPERATION.............8W-97-3
JOINT - DESCRIPTION, LOWER BALL......2-10
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - OPERATION, LOWER BALL.......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-58
JOINT MOLDING - REMOVAL, ROOF......23-58
JOUNCE BUMPER - DESCRIPTION........2-36
JOUNCE BUMPER - OPERATION..........2-36
JUMP STARTING - STANDARD
PROCEDURE.........................0-27
JUNCTION BLOCK - DESCRIPTION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - INSTALLATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - OPERATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - REMOVAL, NON-ABS . . 5-33,
5s-32
KEY - DESCRIPTION, TRANSPONDER.....8Q-6
KEY - OPERATION, TRANSPONDER.......8Q-6
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY................8E-18
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-19
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY
.................8E-18
KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY
............................8E-18
KEY REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY
................8Q-3
KEY REMOTE ENTRY MODULE -
DIAGNOSIS AND TESTING, SENTRY
.......8Q-5
18 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL...................14-5
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL..................14-5
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL.....................14-5
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL......................14-5
LEVEL SWITCH - DESCRIPTION, BRAKE
FLUID..........................5-10,5s-9
LEVEL SWITCH - INSTALLATION, BRAKE
FLUID..........................5-11,5s-10
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-12
LEVEL SWITCH - OPERATION, BRAKE
FLUID..........................5-10,5s-9
LEVEL SWITCH - REMOVAL, BRAKE
FLUID..........................5-11,5s-10
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-12
LEVEL TEST - 2.5L DIESEL - DIAGNOSIS
AND TESTING, SYSTEM CHARGE........24-68
LEVEL TEST - GASOLINE ENGINES -
DIAGNOSIS AND TESTING, SYSTEM
CHARGE............................24-67
LEVER - INSTALLATION, GEAR SHIFT.....19-21
LEVER - PARKING BRAKE -
INSTALLATION...................5-65,5s-67
LEVER - PARKING BRAKE - REMOVAL....5-64,
5s-67
LEVER - REMOVAL, GEAR SHIFT........19-21
LEVER AND BEARING - INSTALLATION,
CLUTCH RELEASE......................6-7
LEVER AND BEARING - REMOVAL,
CLUTCH RELEASE......................6-6
LEVER AND FRONT CABLE -
INSTALLATION, PARKING BRAKE....5-66,5s-69
LEVER AND FRONT CABLE - REMOVAL,
PARKING BRAKE.................5-65,5s-68
LHD - INSTALLATION.....5-38,5-46,5-94,5s-37,
5s-49
LHD - INSTALLATION, MASTER
CYLINDER...........................6-10
LHD - REMOVAL....5-36,5-42,5-90,5s-35,5s-45
LHD - REMOVAL, MASTER CYLINDER......6-9
LHD GEAR - INSTALLATION............19-32
LHD GEAR - REMOVAL................19-27
LICENSE LAMP - INSTALLATION.........8L-17
LICENSE LAMP - REMOVAL............8L-17
LIFT GEAR & LINK ROD - DESCRIPTION . . 8N-16
LIFT GEAR & LINK ROD - INSTALLATION . 8N-16
LIFT GEAR & LINK ROD - OPERATION....8N-16
LIFT GEAR & LINK ROD - REMOVAL.....8N-16
LIFTERS - DIAGNOSIS AND TESTING,
HYDRAULIC.........................9-113
LIFTERS (CAM IN BLOCK) -
DESCRIPTION, HYDRAULIC.............9-113
LIFTERS (CAM IN BLOCK) -
INSTALLATION, HYDRAULIC............9-114
LIFTERS (CAM IN BLOCK) - REMOVAL,
HYDRAULIC.........................9-114
LIFTGATE - INSTALLATION.............23-42
LIFTGATE - REMOVAL.................23-42
LIFTGATE ADJUSTMENT - STANDARD
PROCEDURE.........................8N-9
LIFTGATE CONTROL MODULE -
DESCRIPTION, POWER................8E-10
LIFTGATE CONTROL MODULE -
INSTALLATION, POWER...............8E-11
LIFTGATE CONTROL MODULE -
OPERATION, POWER..................8E-11
LIFTGATE CONTROL MODULE -
REMOVAL, POWER...................8E-11
LIFTGATE LAMP - INSTALLATION
........8L-22
LIFTGATE LAMP - REMOVAL
............8L-22
LIFTGATE LEARN CYCLE - STANDARD
PROCEDURE, POWER
..................8N-9
LIFTGATE MOTOR - DESCRIPTION
.......8N-15
LIFTGATE MOTOR - INSTALLATION
......8N-15
LIFTGATE MOTOR - OPERATION
.........8N-15
LIFTGATE MOTOR - REMOVAL
..........8N-15
LIFTGATE SIDE - INSTALLATION
.........23-44
LIFTGATE SIDE - REMOVAL
............23-44
LIFTGATE SILL PLATE - INSTALLATION
. . . 23-79
LIFTGATE SILL PLATE - REMOVAL
.......23-79
LIFTGATE SPOILER - INSTALLATION
......23-42
LIFTGATE SPOILER - REMOVAL
.........23-42LIFTGATE SYSTEM - DESCRIPTION,
POWER.............................8N-2
LIFTGATE SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................8N-4
LIFTGATE SYSTEM - OPERATION,
POWER.............................8N-3
LIMITS - DESCRIPTION, HIGH AND LOW . . . 25-8
LINE - DESCRIPTION, REFRIGERANT.....24-65
LINE - INSTALLATION, A/C DISCHARGE . . . 24-80
LINE - INSTALLATION, FUEL...........24-118
LINE - INSTALLATION, LIQUID....24-105,24-90
LINE - INSTALLATION, SUCTION . . . 24-107,24-95
LINE - REMOVAL, A/C DISCHARGE.......24-79
LINE - REMOVAL, FUEL...............24-117
LINE - REMOVAL, LIQUID........24-104,24-88
LINE - REMOVAL, SUCTION......24-106,24-94
LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE, GRID..........8G-4
LINE EXTENSION - INSTALLATION, REAR
A/C EVAPORATOR....................24-99
LINE EXTENSION - REMOVAL, A/C
EVAPORATOR.......................24-98
LINES - DESCRIPTION, OIL COOLER.....9-138
LINES - DESCRIPTION, UNDERBODY....24-107
LINES - INSTALLATION, OIL COOLER.....9-138
LINES - INSTALLATION, REAR HEATER . . 24-111
LINES - INSTALLATION, TRANSMISSION
OIL COOLER.........................7-38
LINES - INSTALLATION, UNDERBODY
REFRIGERANT......................24-111
LINES - OPERATION, OIL COOLER.......9-138
LINES - OPERATION, REFRIGERANT......24-65
LINES - OPERATION, UNDERBODY......24-107
LINES - REMOVAL, OIL COOLER........9-138
LINES - REMOVAL, TRANSMISSION OIL
COOLER.............................7-38
LINES - REMOVAL, UNDERBODY
REFRIGERANT......................24-110
LINES/HOSES AND CLAMPS -
DESCRIPTION, FUEL...................14-6
LINING - INSPECTION, REAR DRUM
BRAKE SHOE....................5-22,5s-21
LINK - DESCRIPTION, TRD............21-249
LINK - INSTALLATION, FUEL FILL DOOR
BLOCKER LOCKOUT..................23-54
LINK - INSTALLATION, SEAT RISER
LATCH LOCKING....................23-106
LINK - OPERATION, TRD..............21-249
LINK - REMOVAL, FUEL FILL DOOR
BLOCKER LOCKOUT..................23-53
LINK - REMOVAL, SEAT RISER LATCH
LOCKING..........................23-106
LINK CONNECTOR - DESCRIPTION, DATA . . 8E-6
LINK CONNECTOR - OPERATION, DATA....8E-7
LINK ROD - DESCRIPTION, LIFT GEAR . . . 8N-16
LINK ROD - INSTALLATION, LIFT GEAR . . . 8N-16
LINK ROD - OPERATION, LIFT GEAR.....8N-16
LINK ROD - REMOVAL, LIFT GEAR.......8N-16
LINKAGE - INSTALLATION, WIPER.......8R-14
LINKAGE - REMOVAL, WIPER...........8R-14
LIQUID LINE - INSTALLATION.....24-105,24-90
LIQUID LINE - REMOVAL........24-104,24-88
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL.....8W-01-10
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK...........................0-7
LOCATIONS - SPECIFICATIONS, BODY
SEALING..........................23-130
LOCATIONS - SPECIFICATIONS,
STRUCTURAL ADHESIVE..............23-156
LOCATIONS - SPECIFICATIONS, WELD . . . 23-166
LOCK ASSEMBLY - INSTALLATION,
LATCH .............................23-27
LOCK ASSEMBLY - REMOVAL, LATCH....23-26
LOCK CYLINDER - INSTALLATION . . 23-19,23-42
LOCK CYLINDER - REMOVAL......23-19,23-42
LOCK CYLINDER HOUSING -
INSTALLATION
.......................19-19
LOCK CYLINDER HOUSING - REMOVAL
. . . 19-17
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR
.................8N-4,8N-41
LOCK MOTOR - INSTALLATION, SLIDING
DOOR
.........................8N-44,8N-6
LOCK MOTOR - REMOVAL, SLIDING
DOOR
.........................8N-44,8N-6LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER..........................8N-40
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR.................8N-4,8N-41
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8N-40
LOCK SWITCH - EXPORT -
DESCRIPTION, DOOR CYLINDER.........8N-3
LOCK SWITCH - EXPORT - DIAGNOSIS
AND TESTING, DOOR CYLINDER.........8N-3
LOCK SWITCH - EXPORT -
INSTALLATION, DOOR CYLINDER.........8N-4
LOCK SWITCH - EXPORT - OPERATION,
DOOR CYLINDER.....................8N-3
LOCK SWITCH - EXPORT - REMOVAL,
DOOR CYLINDER.....................8N-3
LOCK SWITCH - INSTALLATION, DOOR....8N-4,
8N-42
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8N-41
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8N-40
LOCK SWITCH - REMOVAL, DOOR . . 8N-4,8N-42
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8N-41
LOCKED ENGINE - STANDARD
PROCEDURE, HYDROSTATIC.........9-10,9-85
LOCKING LINK - INSTALLATION, SEAT
RISER LATCH......................23-106
LOCKING LINK - REMOVAL, SEAT RISER
LATCH ............................23-106
LOCK/LATCH - INSTALLATION, UNDER
SEAT STORAGE BIN.................23-105
LOCK/LATCH - REMOVAL, UNDER SEAT
STORAGE BIN......................23-105
LOCKOUT LINK - INSTALLATION, FUEL
FILL DOOR BLOCKER.................23-54
LOCKOUT LINK - REMOVAL, FUEL FILL
DOOR BLOCKER.....................23-53
LOCKS - DESCRIPTION, POWER....8N-1,8N-38
LOCKS - OPERATION, POWER......8N-2,8N-39
LOUVER - INSTALLATION, REAR HVAC . . . 23-81
LOUVER - REMOVAL, REAR HVAC.......23-81
LOW LIMITS - DESCRIPTION, HIGH.......25-8
LOWER - CLEANING, INTAKE MANIFOLD . . 9-148
LOWER - INSPECTION, INTAKE
MANIFOLD......................9-148,9-60
LOWER - INSTALLATION, INTAKE
MANIFOLD...........................9-60
LOWER - INSTALLATION, SHROUD.......19-22
LOWER - REMOVAL, INTAKE MANIFOLD . . . 9-60
LOWER - REMOVAL, SHROUD..........19-21
LOWER BALL JOINT - DESCRIPTION......2-10
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER BALL JOINT - OPERATION........2-10
LOWER CONSOLE - INSTALLATION......23-69
LOWER CONSOLE - REMOVAL..........23-69
LOWER CONTROL ARM - DESCRIPTION . . . 2-12
LOWER CONTROL ARM - INSPECTION.....2-14
LOWER CONTROL ARM - INSTALLATION . . . 2-16
LOWER CONTROL ARM - OPERATION.....2-12
LOWER CONTROL ARM - REMOVAL......2-12
LOWER CONTROL ARM (REAR BUSHING
- HYDRO) - ASSEMBLY.................2-14
LOWER CONTROL ARM (REAR BUSHING
- HYDRO) - DISASSEMBLY..............2-14
LOWER CONTROL ARM (REAR BUSHING
- STANDARD) - ASSEMBLY..............2-14
LOWER CONTROL ARM (REAR BUSHING
- STANDARD) - DISASSEMBLY...........2-13
LOWER DRIVE UNIT - DESCRIPTION.....8N-32
LOWER DRIVE UNIT - INSTALLATION....8N-33
LOWER DRIVE UNIT - OPERATION.......8N-32
LOWER DRIVE UNIT - REMOVAL........8N-33
LOWER DRIVE UNIT TRACK & RACK -
DESCRIPTION.......................8N-34
LOWER DRIVE UNIT TRACK & RACK -
INSTALLATION......................8N-34
LOWER DRIVE UNIT TRACK & RACK -
OPERATION
.........................8N-34
LOWER DRIVE UNIT TRACK & RACK -
REMOVAL
..........................8N-34
LOWER EXTENSION TRIM -
INSTALLATION, A-PILLAR
..............23-74
LOWER EXTENSION TRIM - REMOVAL,
A-PILLAR
...........................23-74
LOWER HINGE - INSTALLATION
.........23-28
20 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

POWER TRANSFER UNIT, SPECIAL
TOOLS - SDP........................21-8
POWER WINDOWS - DESCRIPTION......8N-62
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-62
POWER WINDOWS - OPERATION........8N-62
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY...................23-1
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY................23-108
PREFERENCE - STANDARD PROCEDURE,
HORN CHIRP...................8N-42,8N-5
PRELOAD - ADJUSTMENT,
DIFFERENTIAL BEARING..............21-199
PRELOAD MEASUREMENT AND
ADJUSTMENT, ADJUSTMENTS -
DIFFERENTIAL BEARING.............21s-100
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE........................9-11,9-85
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.................9-52
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL.........................9-136
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-26
PRESSURE CAP - OPERATION,
RADIATOR...........................7-27
PRESSURE CAP TESTING - DIAGNOSIS
AND TESTING, COOLING SYSTEM........7-27
PRESSURE FOR HIGH SPEED
OPERATION - STANDARD PROCEDURE,
TIRE..........................22-17,22s-9
PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION.....................9-83,9-9
PRESSURE MONITORING -
DESCRIPTION, TIRE..............22-9,22s-1
PRESSURE MONITORING - OPERATION,
TIRE...........................22-9,22s-1
PRESSURE PLATE - 2.5L TD -
INSTALLATION, CLUTCH DISC...........6-12
PRESSURE PLATE - 2.5L TD - REMOVAL,
CLUTCH DISC........................6-11
PRESSURE REGULATOR -
INSTALLATION, FUEL..................14-7
PRESSURE REGULATOR - OPERATION,
FUEL...............................14-7
PRESSURE REGULATOR - REMOVAL,
FUEL...............................14-7
PRESSURE RELEASE PROCEDURE -
STANDARD PROCEDURE, FUEL
SYSTEM............................14-2
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-73
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-141
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-73
PRESSURE RELIEF VALVE - REMOVAL,
OIL
................................9-141
PRESSURE SENSOR - DIAGNOSIS AND
TESTING, TIRE
..................22-10,22s-2
PRESSURE SENSOR RETRAIN -
STANDARD PROCEDURE, TIRE
.....22-10,22s-2
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM
............................14-3
PRESSURE SWITCH - DESCRIPTION, OIL
. 9-141
PRESSURE SWITCH - INSTALLATION,
OIL
...........................9-141,9-54
PRESSURE SWITCH - OPERATION, OIL
. . . 9-141
PRESSURE SWITCH - REMOVAL, OIL
....9-141,
9-54
PRESSURE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMPRESSION
. . . 9-83,9-9
PRESSURE TEST - DIAGNOSIS AND
TESTING, POWER STEERING SYSTEM
FLOW
...............................19-1
PRESSURE TESTS - DIAGNOSIS AND
TESTING, CLUTCH AIR
.........21-122,21s-30
PRESSURE TESTS - DIAGNOSIS AND
TESTING, HYDRAULIC
..........21-120,21s-28
PRESSURE TRANSDUCER -
DESCRIPTION, A/C
...................24-21PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-22
PRESSURE TRANSDUCER -
INSTALLATION, A/C...................24-22
PRESSURE TRANSDUCER - OPERATION,
A/C................................24-21
PRESSURE TRANSDUCER - REMOVAL,
A/C................................24-22
PRESSURES - STANDARD PROCEDURE,
TIRE INFLATION.................22-16,22s-8
PROBLEM CAUSES - DIAGNOSIS AND
TESTING, COMMON..................21-30
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER.......8N-43
PROGRAMMABLE COMMUNICATIONS
INTERFACE (PCI) BUS, OPERATION......14-21
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER................8M-7
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM................8E-2
PROGRAMMING - STANDARD
PROCEDURE, REMOTE KEYLESS
ENTRY TRANSMITTER.................8N-5
PROGRAMMING - STANDARD
PROCEDURE, TRANSPONDER...........8Q-6
PROPELLER SHAFT - DESCRIPTION.......3-21
PROPELLER SHAFT - INSTALLATION......3-22
PROPELLER SHAFT - OPERATION........3-21
PROPELLER SHAFT - REMOVAL..........3-21
PROPELLER SHAFT - SPECIFICATIONS.....3-22
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE............5-75
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-77
PROPORTIONING VALVE (HEIGHT
SENSING) - DESCRIPTION.........5-48,5s-51
PROPORTIONING VALVE (HEIGHT
SENSING) - DIAGNOSIS AND TESTING....5-49,
5s-52
PROPORTIONING VALVE (HEIGHT
SENSING) - INSTALLATION.........5-51,5s-53
PROPORTIONING VALVE (HEIGHT
SENSING) - OPERATION...........5-48,5s-51
PROPORTIONING VALVE (HEIGHT
SENSING) - REMOVAL............5-50,5s-53
PTU FLUID CHANGE - STANDARD
PROCEDURE.........................21-5
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER....................8F-25,8F-27
PULLEY - DIAGNOSIS AND TESTING,
GENERATOR DECOUPLER.........8F-25,8F-27
PULLEY - INSTALLATION, GENERATOR
DECOUPLER....................8F-26,8F-28
PULLEY - INSTALLATION, TIMING BELT
TENSIONER..........................9-69
PULLEY - OPERATION, GENERATOR
DECOUPLER....................8F-25,8F-27
PULLEY - REMOVAL, GENERATOR
DECOUPLER....................8F-26,8F-28
PULLEY - REMOVAL, TIMING BELT
TENSIONER..........................9-68
PUMP - 2.4L - CLEANING, WATER........7-32
PUMP - 2.4L - DESCRIPTION, WATER.....7-31
PUMP - 2.4L - INSPECTION, WATER......7-32
PUMP - 2.4L - INSTALLATION, WATER.....7-32
PUMP - 2.4L - REMOVAL, WATER........7-31
PUMP - 3.3/3.8L - CLEANING, WATER.....7-34
PUMP - 3.3/3.8L - DESCRIPTION,
WATER .............................7-33
PUMP - 3.3/3.8L - INSPECTION, WATER . . . 7-34
PUMP - 3.3/3.8L - INSTALLATION,
WATER .............................7-34
PUMP - 3.3/3.8L - REMOVAL, WATER.....7-33
PUMP - ASSEMBLY, OIL...........9-143,9-56
PUMP - ASSEMBLY, OIL.......21-232,21s-132
PUMP - CLEANING, OIL...........9-142,9-56
PUMP - DESCRIPTION, FUEL............14-8
PUMP - DESCRIPTION, FUEL DOSING . . . 24-115
PUMP - DESCRIPTION, OIL.............9-142
PUMP - DESCRIPTION, OIL.....21-230,21s-131
PUMP - DISASSEMBLY, OIL........9-142,9-55
PUMP - DISASSEMBLY, OIL
....21-230,21s-131
PUMP - INSPECTION, OIL
..........9-142,9-56
PUMP - INSTALLATION, FUEL DOSING
. . . 24-116
PUMP - INSTALLATION, LEAK
DETECTION
.........................25-13
PUMP - INSTALLATION, OIL
........9-144,9-57PUMP - INSTALLATION, SEAL - OIL....21-233,
21s-133
PUMP - OPERATION, FUEL..............14-8
PUMP - OPERATION, FUEL DOSING.....24-115
PUMP - OPERATION, OIL......21-230,21s-131
PUMP - REMOVAL, FUEL DOSING......24-115
PUMP - REMOVAL, LEAK DETECTION....25-13
PUMP - REMOVAL, OIL............9-142,9-55
PUMP - REMOVAL, SEAL - OIL . . 21-232,21s-133
PUMP (2.4L ENGINE) - INSTALLATION....19-42
PUMP (2.4L ENGINE) - REMOVAL.......19-38
PUMP (2.4L/3.3L/3.8L ENGINE) -
DESCRIPTION.......................19-36
PUMP (2.5L DIESEL) - DESCRIPTION.....19-36
PUMP (2.5L DIESEL) - INSTALLATION....19-43
PUMP (2.5L DIESEL) - REMOVAL........19-40
PUMP (3.3L/3.8L ENGINE) -
INSTALLATION.......................19-43
PUMP (3.3L/3.8L ENGINE) - REMOVAL . . . 19-40
PUMP INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING........19-37
PUMP INLET TUBE - 2.4L -
DESCRIPTION, WATER.................7-35
PUMP INLET TUBE - 2.4L -
INSTALLATION, WATER.................7-35
PUMP INLET TUBE - 2.4L - REMOVAL,
WATER .............................7-35
PUMP INLET TUBE - 3.3/3.8L -
INSTALLATION, WATER.................7-36
PUMP INLET TUBE - 3.3/3.8L -
REMOVAL, WATER....................7-36
PUMP MODULE - DESCRIPTION, FUEL....14-8
PUMP MODULE - INSTALLATION, FUEL....14-9
PUMP MODULE - OPERATION, FUEL......14-8
PUMP MODULE - REMOVAL, FUEL........14-8
PUMP MOTOR - INSTALLATION, FRONT
WASHER............................8R-8
PUMP MOTOR - INSTALLATION, REAR
WASHER...........................8R-10
PUMP MOTOR - REMOVAL, FRONT
WASHER............................8R-8
PUMP MOTOR - REMOVAL, REAR
WASHER...........................8R-10
PUMP (PULLEY) - ASSEMBLY..........19-41
PUMP (PULLEY) - DISASSEMBLY........19-41
PUMP RELAY - DESCRIPTION, FUEL.....14-28
PUMP RELAY - OPERATION, FUEL.......14-28
PUMP, SPECIAL TOOLS - POWER
STEERING..........................19-43
PUSH-PIN GROMMET REPLACEMENT -
STANDARD PROCEDURE..............8N-28
PUSHRODS - DESCRIPTION.......9-109,9s-26
PUSHRODS - OPERATION.........9-109,9s-26
QUAD BUCKET - INSTALLATION, BUCKET
SEAT BACK.........................23-99
QUAD BUCKET - INSTALLATION, SEAT
BELT BUCKLE - FIRST ROW INBOARD....8O-12
QUAD BUCKET - REMOVAL, BUCKET
SEAT BACK.........................23-98
QUAD BUCKET - REMOVAL, SEAT BELT
BUCKLE - FIRST ROW INBOARD........8O-12
QUAD BUCKET, 50/50 SPLIT, BENCH -
INSTALLATION, SEAT BACK HINGE
COVERS...........................23-101
QUAD BUCKET, 50/50 SPLIT, BENCH -
INSTALLATION, SEAT CUSHION COVER . . 23-100
QUAD BUCKET, 50/50 SPLIT, BENCH -
REMOVAL, SEAT BACK HINGE COVERS . . 23-101
QUAD BUCKET, 50/50 SPLIT, BENCH -
REMOVAL, SEAT CUSHION COVER......23-100
QUAD BUCKET SEAT RISER -
INSTALLATION.......................23-98
QUAD BUCKET SEAT RISER - REMOVAL . . 23-98
QUAD BUCKET SEAT SIDE SHIELD - NO
CUPHOLDER - INSTALLATION...........23-97
QUAD BUCKET SEAT SIDE SHIELD - NO
CUPHOLDER - REMOVAL..............23-97
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - FLAP AND SPRING
ASSEMBLY - INSTALLATION
...........23-107
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - FLAP AND SPRING
ASSEMBLY - REMOVAL
...............23-107
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - INSTALLATION
...........23-96
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - REMOVAL
..............23-96
QUAD CHILD SEAT - INSTALLATION
......23-89
26 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SET SWITCH - REMOVAL, MEMORY.....8N-13,
8N-56
SETTING - STANDARD PROCEDURE,
PINION FACTOR................8E-15,8E-23
SETTING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-11
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHAFT - ASSEMBLY, INPUT........21-96,21s-5
SHAFT - ASSEMBLY, INTERMEDIATE....21-107,
21s-17
SHAFT - ASSEMBLY, ROCKER ARMS.....9-109,
9s-27
SHAFT - DESCRIPTION, INPUT.....21-93,21s-1
SHAFT - DESCRIPTION, INTERMEDIATE . 21-100,
21s-9
SHAFT - DESCRIPTION, PROPELLER......3-21
SHAFT - DESCRIPTION, SHIFT FORK....21-113
SHAFT - DIAGNOSIS AND TESTING,
HALF............................3-1,3-13
SHAFT - DISASSEMBLY, INPUT.....21-93,21s-1
SHAFT - DISASSEMBLY, INTERMEDIATE . 21-100,
21s-10
SHAFT - DISASSEMBLY, ROCKER ARMS . . 9-109,
9s-27
SHAFT - FRONT - DESCRIPTION, HALF.....3-1
SHAFT - FRONT - INSTALLATION, HALF.....3-4
SHAFT - FRONT - REMOVAL, HALF........3-2
SHAFT - FRONT - SPECIFICATIONS, HALF . . 3-15,
3-6
SHAFT - INSTALLATION, PROPELLER......3-22
SHAFT - INSTALLATION, ROCKER ARMS . . 9-110,
9s-28
SHAFT - OPERATION, PROPELLER........3-21
SHAFT - REAR - DESCRIPTION, HALF.....3-13
SHAFT - REAR - INSTALLATION, HALF.....3-14
SHAFT - REAR - REMOVAL, HALF........3-13
SHAFT - REMOVAL, PROPELLER.........3-21
SHAFT - REMOVAL, ROCKER ARMS . 9-109,9s-27
SHAFT - RHD - INSTALLATION, PEDAL
TORQUE........................5-39,5s-43
SHAFT - RHD - REMOVAL, PEDAL
TORQUE........................5-39,5s-42
SHAFT - SPECIFICATIONS, PROPELLER....3-22
SHAFT COVER SEAL - INSTALLATION,
INPUT.............................21-14
SHAFT COVER SEAL - REMOVAL, INPUT . . 21-13
SHAFT END SEAL - INSTALLATION,
INPUT.............................21-16
SHAFT END SEAL - REMOVAL, INPUT....21-15
SHAFT INNER SEAL - INSTALLATION,
HALF..............................21-12
SHAFT INNER SEAL - REMOVAL, HALF . . . 21-12
SHAFT SEAL - INSTALLATION, INPUT.....21-18
SHAFT SEAL - INSTALLATION, OUTER
HALF..............................21-19
SHAFT SEAL - REMOVAL, INPUT........21-17
SHAFT SEAL - REMOVAL, OUTER HALF . . . 21-19
SHAFTS AND CARRIER ASSEMBLY -
DESCRIPTION, BALANCE................9-69
SHAFTS AND CARRIER ASSEMBLY -
INSTALLATION, BALANCE...............9-72
SHAFTS AND CARRIER ASSEMBLY -
OPERATION, BALANCE.................9-69
SHAFTS AND CARRIER ASSEMBLY -
REMOVAL, BALANCE...................9-69
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH................23-55
SHIELD - NO CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT
SIDE..............................23-97
SHIELD - NO CUPHOLDER - REMOVAL,
QUAD BUCKET SEAT SIDE.............23-97
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH................23-55
SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT SIDE............23-107
SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT SIDE
..................23-107
SHIELD/CUPHOLDER - INSTALLATION,
QUAD BUCKET SEAT SIDE
.............23-96
SHIELD/CUPHOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE
...................23-96
SHIELDS - DESCRIPTION, HEAT
..........11-6
SHIELDS - INSTALLATION, HEAT
.........11-7SHIELDS - OPERATION, HEAT............11-7
SHIELDS - REMOVAL, HEAT.............11-7
SHIFT CABLE - INSTALLATION, GEAR....21-205
SHIFT CABLE - REMOVAL, GEAR.......21-204,
21s-105
SHIFT COVER - DESCRIPTION.........21-113
SHIFT FORK AND SHAFT - DESCRIPTION . 21-113
SHIFT INTERLOCK SOLENOID -
DESCRIPTION...............21-233,21s-133
SHIFT INTERLOCK SOLENOID -
DIAGNOSIS AND TESTING, BRAKE/
TRANSMISSION..............21-235,21s-135
SHIFT INTERLOCK SOLENOID -
INSTALLATION...............21-236,21s-136
SHIFT INTERLOCK SOLENOID -
OPERATION.................21-233,21s-134
SHIFT INTERLOCK SOLENOID -
REMOVAL..................21-235,21s-135
SHIFT LEVER - INSTALLATION, GEAR.....19-21
SHIFT LEVER - REMOVAL, GEAR........19-21
SHIM SELECTION, ADJUSTMENTS -
OUTPUT FLANGE......................21-7
SHOCK ABSORBER - DESCRIPTION.......2-37
SHOCK ABSORBER - INSTALLATION......2-38
SHOCK ABSORBER - OPERATION.........2-37
SHOCK ABSORBER - REMOVAL..........2-37
SHOCK ABSORBER (UPPER BUSHING) -
ASSEMBLY..........................2-38
SHOCK ABSORBER (UPPER BUSHING) -
DISASSEMBLY........................2-37
SHOE LINING - INSPECTION, REAR
DRUM BRAKE...................5-22,5s-21
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-73,
5s-76
SHOES - ADJUSTMENT, REAR DRUM
BRAKE.........................5-23,5s-22
SHOES - CLEANING, DISC BRAKE....5-16,5-18,
5s-15,5s-17
SHOES - INSPECTION, DISC BRAKE . . 5-16,5-18,
5s-15,5s-17
SHOES - INSTALLATION, REAR DISC
BRAKE.........................5-19,5s-18
SHOES - INSTALLATION, REAR DRUM
BRAKE.........................5-22,5s-21
SHOES - PARKING BRAKE -
INSTALLATION...................5-72,5s-75
SHOES - PARKING BRAKE - REMOVAL....5-67,
5s-69
SHOES - REMOVAL, REAR DISC BRAKE . . . 5-17,
5s-16
SHOES - REMOVAL, REAR DRUM BRAKE . . 5-19,
5s-18
SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5s-15
SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL, FRONT DISC BRAKE.........5s-14
SHOES (DISC/DISC BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-16
SHOES (DISC/DISC BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-14
SHOES (DISC/DRUM BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-17
SHOES (DISC/DRUM BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-15
SHOES (TRW BRAKES) - INSTALLATION,
FRONT DISC BRAKE..................5s-16
SHOES (TRW BRAKES) - REMOVAL,
FRONT DISC BRAKE
..................5s-14
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
..........................8W-01-10
SHROUD - LOWER - INSTALLATION
......19-22
SHROUD - LOWER - REMOVAL
.........19-21
SHROUD - UPPER - INSTALLATION
......19-23
SHROUD - UPPER - REMOVAL
..........19-23
SHUT DOWN RELAY - DESCRIPTION,
AUTO
...............................8I-3
SHUT DOWN RELAY - OPERATION, AUTO
. . . 8I-3
SIDE - INSTALLATION, LIFTGATE
........23-44
SIDE - REMOVAL, LIFTGATE
............23-44
SIDE COVER - INSTALLATION, FRONT
SEAT CUSHION
......................23-94
SIDE COVER - REMOVAL, FRONT SEAT
CUSHION
...........................23-94SIDE GEAR END PLAY - ADJUSTMENT,
DIFFERENTIAL.......................21-70
SIDE MOLDINGS - INSTALLATION, BODY . . 23-46
SIDE MOLDINGS - REMOVAL, BODY.....23-45
SIDE SHIELD - NO CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-97
SIDE SHIELD - NO CUPHOLDER -
REMOVAL, QUAD BUCKET SEAT.........23-97
SIDE SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT.................23-107
SIDE SHIELD/CUPHOLDER - FLAP AND
SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT......................23-107
SIDE SHIELD/CUPHOLDER -
INSTALLATION, QUAD BUCKET SEAT.....23-96
SIDE SHIELD/CUPHOLDER - REMOVAL,
QUAD BUCKET SEAT..................23-96
SIDE VIEW MIRROR - INSTALLATION.....23-59
SIDE VIEW MIRROR - REMOVAL........23-59
SIDE VIEW MIRROR GLASS -
INSTALLATION.......................23-59
SIDE VIEW MIRROR GLASS - REMOVAL . . 23-59
SIDEVIEW MIRROR - REMOVAL.........8N-49
SIGNAL LAMP - INSTALLATION,
PARK/TURN.........................8L-18
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-18
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-17
SIGNAL SYSTEM - OPERATION, TURN....8L-18
SILL PLATE - INSTALLATION, LIFTGATE . . . 23-79
SILL PLATE - INSTALLATION, SLIDING
DOOR.............................23-82
SILL PLATE - REMOVAL, LIFTGATE.......23-79
SILL PLATE - REMOVAL, SLIDING DOOR . . 23-82
SILL TRIM PLATE - INSTALLATION,
DOOR.............................23-77
SILL TRIM PLATE - REMOVAL, DOOR....23-77
SINGLE ZONE - DESCRIPTION...........24-2
SINGLE ZONE - OPERATION.............24-4
SLAVE CYLINDER - INSTALLATION........6-11
SLAVE CYLINDER - REMOVAL...........6-11
SLEEVE - INSTALLATION, HEADREST.....23-90
SLEEVE - REMOVAL, HEADREST........23-90
SLIDING DOOR - INSTALLATION.........23-30
SLIDING DOOR - REMOVAL............23-29
SLIDING DOOR ADJUSTMENT -
STANDARD PROCEDURE..............8N-28
SLIDING DOOR ADJUSTMENTS,
ADJUSTMENTS......................23-30
SLIDING DOOR CONTROL MODULE -
DESCRIPTION.......................8E-19
SLIDING DOOR CONTROL MODULE -
INSTALLATION.......................8E-20
SLIDING DOOR CONTROL MODULE -
OPERATION.........................8E-19
SLIDING DOOR CONTROL MODULE -
REMOVAL..........................8E-19
SLIDING DOOR GLASS - INSTALLATION . . 23-110
SLIDING DOOR GLASS - REMOVAL.....23-110
SLIDING DOOR LOCK MOTOR -
INSTALLATION..................8N-44,8N-6
SLIDING DOOR LOCK MOTOR -
REMOVAL......................8N-44,8N-6
SLIDING DOOR MOTOR - DESCRIPTION . . 8N-30
SLIDING DOOR MOTOR - INSTALLATION . . 8N-31
SLIDING DOOR MOTOR - OPERATION....8N-30
SLIDING DOOR MOTOR - REMOVAL
.....8N-30
SLIDING DOOR SILL PLATE -
INSTALLATION
.......................23-82
SLIDING DOOR SILL PLATE - REMOVAL
. . 23-82
SLIDING DOOR STOP BUMPER BEZEL -
INSTALLATION
.......................23-25
SLIDING DOOR STOP BUMPER BEZEL -
REMOVAL
..........................23-25
SLIDING DOOR SYSTEM - DESCRIPTION,
POWER
............................8N-19
SLIDING DOOR SYSTEM - DIAGNOSIS
AND TESTING, POWER
................8N-22
SLIDING DOOR SYSTEM - OPERATION,
POWER
............................8N-21
SLIDING DOOR WEATHERSTRIP -
INSTALLATION
......................23-115
SLIDING DOOR WEATHERSTRIP -
REMOVAL
.........................23-115
SOCKET - INSTALLATION, STABILIZER
....23-33
SOCKET - REMOVAL, STABILIZER
.......23-33
SOLENOID - DESCRIPTION, EVAP/PURGE
. 25-12
32 INDEXRS
Description Group-Page Description Group-Page Description Group-Page