2004 CHRYSLER VOYAGER radiator

(4) Install the two screws that secure the rear A/C
expansion valve to the evaporator tube sealing plate.
Tighten the screws to 11 N´m (97 in. lbs.).
(5) Install the rear evaporator line extension onto
the expansion valve (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING - REAR/EVAPORA-
TOR - INSTALLATION - EVAPORATOR LINE
EXTENSION).
(6) Install the foam insulator wrap over the rear
expansion valve.
(7) Install the rear HVAC housing (Refer to 24 -
HEATING & AIR CONDITIONING/DISTRIBUTION/
HVAC HOUSING - INSTALLATION).
(8) Run the HVAC Cooldown Test to verify proper
operation.
HEATER CORE
DESCRIPTION
The rear heater core is located near the front of
the rear HVAC housing, behind the right rear wheel
house. It is a heat exchanger made of rows of tubes
and fins. One end of the core is fitted with a molded
plastic tank that includes integral heater core inlet
and outlet nipples. The rear heater core can be ser-
viced without removing the rear HVAC housing from
the vehicle.
OPERATION
Engine coolant is circulated through underbody
heater hoses to the rear heater core at all times. As
the coolant flows through the rear heater core, heat
removed from the engine is transferred to the heater
core fins and tubes. Air directed through the heater
core picks up the heat from the heater core fins. The
rear blend door allows control of the rear heater out-
put air temperature by controlling how much of the
air flowing through the rear HVAC housing is
directed through the heater core.
The rear heater core cannot be repaired and, if
faulty or damaged, it must be replaced.
STANDARD PROCEDURE - REAR HEATER
CORE FILLING
In its final installed position, the rear heater core
is positioned higher than the radiator fill cap. There-
fore, when the cooling system is drained and refilled,
gravity will not refill the heater core with coolant to
the proper level. This may result in two problems:1.
Insufficient coolant level in the engine cooling sys-
tem, which may result in engine overheating.2.Air
entrapped within the rear heater core, which may
result in insufficient rear heater performance. There
are two methods that may be employed to prevent
these problems:1.Pre-filling of the rear heater core.2.Thermal cycling of the engine cooling system. Fol-
lowing are descriptions of both prevention methods,
as well as a method to verify rear heater perfor-
mance.
WARNING: REFER TO THE APPLICABLE WARN-
INGS AND CAUTIONS FOR THIS SYSTEM BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING
FRONT - WARNING - HEATER PLUMBING).
PRE-FILLING
If the rear heater core or the rear HVAC housing
have been removed from the vehicle for service, the
rear heater core may be pre-filled with the proper
engine coolant mixture prior to reconnecting the
heater hoses to the heater core hose fittings.
(1) The heater core should be installed in the rear
HVAC housing, and the rear HVAC housing should
be installed in the vehicle.
(2) Take the proper precautions to protect the car-
peting below the rear heater core from spilled engine
coolant and have absorbent toweling readily avail-
able to mop up any spills.
(3) Insert the small end of an appropriate funnel
into the upper hose fitting of the heater core (Fig. 4).
(4) Carefully pour the proper pre-mixed engine
coolant solution into the rear heater core through a
funnel until coolant begins to appear at the lower
hose fitting of the heater core.
(5) Use absorbent toweling to clean up any engine
coolant spills from the preceding operation.
(6) Reconnect the heater hoses to the rear heater
core (Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING - REAR/HEATER HOSE - INSTAL-
LATION).
Fig. 4 Pre-Filling Heater Core - Typical
1 - REAR HEATER CORE
RSPLUMBING - REAR24 - 101
A/C EXPANSION VALVE (Continued)

The following is a list of the monitored compo-
nents:
²Comprehensive Components
²Oxygen Sensor Monitor
²Oxygen Sensor Heater Monitor
²Catalyst Monitor
COMPREHENSIVE COMPONENTS
Along with the major monitors, OBD II requires
that the diagnostic system monitor any component
that could affect emissions levels. In many cases,
these components were being tested under OBD I.
The OBD I requirements focused mainly on testing
emissions-related components for electrical opens and
shorts.
However, OBD II also requires that inputs from
powertrain components to the PCM be tested for
rationality, and that outputs to powertrain compo-
nents from the PCM be tested forfunctionality.
Methods for monitoring the various Comprehensive
Component monitoring include:
(1) Circuit Continuity
²Open
²Shorted high
²Shorted to ground
(2) Rationality or Proper Functioning
²Inputs tested for rationality
²Outputs tested for functionality
NOTE: Comprehensive component monitors are
continuous. Therefore, enabling conditions do not
apply.
Input RationalityÐWhile input signals to the
PCM are constantly being monitored for electrical
opens and shorts, they are also tested for rationality.
This means that the input signal is compared against
other inputs and information to see if it makes sense
under the current conditions.
PCM sensor inputs that are checked for rationality
include:
²Manifold Absolute Pressure (MAP) Sensor
²Oxygen Sensor (O2S)
²Engine Coolant Temperature (ECT) Sensor
²Camshaft Position (CMP) Sensor
²Vehicle Speed Sensor
²Crankshaft Position (CKP) Sensor
²Intake/inlet Air Temperature (IAT) Sensor
²Throttle Position (TPS) Sensor
²Ambient Temperature Sensors
²Power Steering Switch
²Oxygen Sensor Heater
²Brake Switch
²Leak Detection Pump Switch or NVLD switch (if
equipped)
²P/N SwitchOutput FunctionalityÐPCM outputs are tested
for functionality in addition to testing for opens and
shorts. When the PCM provides a voltage to an out-
put component, it can verify that the command was
carried out by monitoring specific input signals for
expected changes. For example, when the PCM com-
mands the Idle Air Control (IAC) Motor to a specific
position under certain operating conditions, it expects
to see a specific (target) idle speed (RPM). If it does
not, it stores a DTC.
PCM outputs monitored for functionality include:
²Fuel Injectors
²Ignition Coils
²Idle Air Control
²Purge Solenoid
²EGR Solenoid (if equipped)
²LDP Solenoid or NVLD solenoid (if equipped)
²Radiator Fan Control
²Trans Controls
OXYGEN SENSOR (O2S) MONITOR
DESCRIPTIONÐEffective control of exhaust
emissions is achieved by an oxygen feedback system.
The most important element of the feedback system
is the O2S. The O2S is located in the exhaust path.
Once it reaches operating temperature 300É to 350ÉC
(572É to 662ÉF), the sensor generates a voltage that
is inversely proportional to the amount of oxygen in
the exhaust. When there is a large amount of oxygen
in the exhaust caused by a lean condition, the sensor
produces a low voltage, below 450 mV. When the oxy-
gen content is lower, caused by a rich condition, the
sensor produces a higher voltage, above 450mV (volt-
ages are offset by 2.5 volts on NGC vehicles).
The information obtained by the sensor is used to
calculate the fuel injector pulse width. The PCM is
programmed to maintain the optimum air/fuel ratio.
At this mixture ratio, the catalyst works best to
remove hydrocarbons (HC), carbon monoxide (CO)
and nitrous oxide (NOx) from the exhaust.
The O2S is also the main sensing element for the
EGR (if equipped), Catalyst and Fuel Monitors.
The O2S may fail in any or all of the following
manners:
²Slow response rate (Big Slope)
²Reduced output voltage (Half Cycle)
²Heater Performance
Slow Response Rate (Big Slope)ÐResponse rate
is the time required for the sensor to switch from
lean to rich signal output once it is exposed to a
richer than optimum A/F mixture or vice versa. As
the PCM adjusts the air/fuel ratio, the sensor must
be able to rapidly detect the change. As the sensor
ages, it could take longer to detect the changes in the
oxygen content of the exhaust gas. The rate of
change that an oxygen sensor experiences is called
25 - 2 EMISSIONS CONTROLRS
EMISSIONS CONTROL (Continued)

CABLE - DIAGNOSIS AND TESTING,
ANTENNA BODY......................8A-4
CABLE - DIAGNOSIS AND TESTING,
BATTERY...........................8F-16
CABLE - INSTALLATION................8P-4
CABLE - INSTALLATION, ANTENNA BODY . . 8A-6
CABLE - INSTALLATION, FRONT.....5-64,5s-67
CABLE - INSTALLATION, GEAR SHIFT....21-205
CABLE - INSTALLATION, HOLD OPEN
LATCH .............................23-38
CABLE - INSTALLATION, INSIDE HANDLE . . 23-38
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-9
CABLE - INSTALLATION, LATCH RELEASE . 23-62
CABLE - INSTALLATION, OUTSIDE
HANDLE............................23-37
CABLE - INSTALLATION, PARKING
BRAKE LEVER AND FRONT.........5-66,5s-69
CABLE - INSTALLATION, THROTTLE
CONTROL..........................14-36
CABLE - OPERATION...................8P-4
CABLE - OPERATION, ANTENNA BODY.....8A-4
CABLE - REMOVAL....................8P-4
CABLE - REMOVAL, ANTENNA BODY......8A-5
CABLE - REMOVAL, FRONT.........5-64,5s-67
CABLE - REMOVAL, GEAR SHIFT.......21-204,
21s-105
CABLE - REMOVAL, HOLD OPEN LATCH . . . 23-38
CABLE - REMOVAL, INSIDE HANDLE.....23-37
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-8
CABLE - REMOVAL, LATCH RELEASE.....23-61
CABLE - REMOVAL, OUTSIDE HANDLE....23-37
CABLE - REMOVAL, PARKING BRAKE
LEVER AND FRONT...............5-65,5s-68
CABLE - REMOVAL, THROTTLE
CONTROL..........................14-35
CABLE - SELECTOR - INSTALLATION,
GEARSHIFT.........................21-84
CABLE - SELECTOR - REMOVAL,
GEARSHIFT.........................21-81
CABLE ADJUSTMENT, ADJUSTMENTS -
GEARSHIFT........................21-206
CABLE ADJUSTMENT, INSTALLATION -
SYNCHRONIZING...............23-102,23-88
CABLE (FRONT) - INSTALLATION,
PARKING BRAKE.................5-63,5s-65
CABLE (FRONT) - REMOVAL, PARKING
BRAKE.........................5-59,5s-62
CABLE (INTERMEDIATE) -
INSTALLATION, PARKING BRAKE
....5-63,5s-66
CABLE (INTERMEDIATE) - REMOVAL,
PARKING BRAKE
.................5-60,5s-62
CABLE (LEFT REAR) - INSTALLATION,
PARKING BRAKE
.................5-64,5s-66
CABLE (LEFT REAR) - REMOVAL,
PARKING BRAKE
.................5-62,5s-64
CABLE RESISTANCE, SPECIFICATIONS -
SPARK PLUG
.........................8I-2
CABLE (RIGHT REAR) - INSTALLATION,
PARKING BRAKE
.................5-63,5s-66
CABLE (RIGHT REAR) - REMOVAL,
PARKING BRAKE
.................5-60,5s-63
CABLES - ADJUSTMENT, PARKING
BRAKE
.........................5-64,5s-66
CABLES - DESCRIPTION, BATTERY
.......8F-16
CABLES - INSTALLATION, BATTERY
......8F-18
CABLES - OPERATION, BATTERY
........8F-16
CABLES - REMOVAL, BATTERY
..........8F-18
CALIBRATION - STANDARD PROCEDURE,
A/C-HEATER CONTROL
................24-20
CALIBRATION - STANDARD PROCEDURE,
COMPASS
...........................8M-3
CALIPER - CLEANING
....5-25,5-29,5s-24,5s-28
CALIPER - INSPECTION
. . . 5-25,5-29,5s-24,5s-28
CALIPER - INSTALLATION, REAR DISC
BRAKE
.........................5-30,5s-29
CALIPER - REMOVAL, REAR DISC
BRAKE
.........................5-27,5s-26
CALIPER ADAPTER - INSTALLATION,
FRONT DISC BRAKE
..............5-31,5s-30
CALIPER ADAPTER - REMOVAL, FRONT
DISC BRAKE
....................5-31,5s-30
CALIPER (CONTINENTAL TEVES
BRAKES) - INSTALLATION, FRONT
DISC BRAKE
........................5s-26CALIPER (CONTINENTAL TEVES
BRAKES) - REMOVAL, FRONT DISC
BRAKE.............................5s-23
CALIPER (DISC/DISC BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-27
CALIPER (DISC/DISC BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-24
CALIPER (DISC/DRUM BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5-27
CALIPER (DISC/DRUM BRAKES) -
REMOVAL, FRONT DISC BRAKE..........5-24
CALIPER GUIDE PIN BUSHINGS
(CONTINENTAL TEVES BRAKES) -
ASSEMBLY..........................5s-24
CALIPER GUIDE PIN BUSHINGS
(CONTINENTAL TEVES BRAKES) -
DISASSEMBLY.......................5s-23
CALIPER GUIDE PIN BUSHINGS
(DISC/DISC BRAKES) - ASSEMBLY........5-25
CALIPER GUIDE PIN BUSHINGS
(DISC/DISC BRAKES) - DISASSEMBLY.....5-24
CALIPER GUIDE PINS (DISC/DRUM
BRAKES) - INSTALLATION, DISC
BRAKE..............................5-31
CALIPER GUIDE PINS (DISC/DRUM
BRAKES) - REMOVAL, DISC BRAKE.......5-31
CALIPER GUIDE PINS (TRW BRAKES) -
INSTALLATION, DISC BRAKE............5s-30
CALIPER GUIDE PINS (TRW BRAKES) -
REMOVAL, DISC BRAKE...............5s-30
CALIPER PISTON AND SEAL -
ASSEMBLY.............5-26,5-29,5s-25,5s-28
CALIPER PISTON AND SEAL -
DISASSEMBLY..........5-24,5-28,5s-23,5s-27
CALIPER (TRW BRAKES) -
INSTALLATION, FRONT DISC BRAKE......5s-26
CALIPER (TRW BRAKES) - REMOVAL,
FRONT DISC BRAKE..................5s-23
CAMSHAFT & BEARINGS (IN BLOCK) -
DESCRIPTION.......................9-115
CAMSHAFT & BEARINGS (IN BLOCK) -
INSPECTION........................9-115
CAMSHAFT & BEARINGS (IN BLOCK) -
INSTALLATION.......................9-115
CAMSHAFT & BEARINGS (IN BLOCK) -
OPERATION.........................9-115
CAMSHAFT & BEARINGS (IN BLOCK) -
REMOVAL..........................9-115
CAMSHAFT END PLAY - STANDARD
PROCEDURE, MEASURING..............9-29
CAMSHAFT OIL SEAL(S) - INSTALLATION . . 9-28
CAMSHAFT OIL SEAL(S) - REMOVAL......9-27
CAMSHAFT POSITION SENSOR -
DESCRIPTION.........................8I-4
CAMSHAFT POSITION SENSOR -
OPERATION..........................8I-4
CAMSHAFT SPROCKET - INSTALLATION,
TIMING CHAIN.......................9-157
CAMSHAFT SPROCKET - REMOVAL,
TIMING CHAIN.......................9-156
CAMSHAFT SPROCKETS - INSTALLATION . . 9-65
CAMSHAFT SPROCKETS - REMOVAL......9-64
CAMSHAFT(S) - CLEANING..............9-29
CAMSHAFT(S) - DESCRIPTION...........9-28
CAMSHAFT(S) - INSPECTION............9-30
CAMSHAFT(S) - INSTALLATION..........9-30
CAMSHAFT(S) - OPERATION.............9-28
CAMSHAFT(S) - REMOVAL..............9-29
CANISTER - DESCRIPTION, VAPOR......25-18
CANISTER - INSTALLATION, REAR EVAP . . 25-20
CANISTER - OPERATION, VAPOR........25-18
CANISTER - REMOVAL, REAR EVAP......25-19
CAP - DESCRIPTION, FUEL FILLER.......25-12
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-26
CAP - INSTALLATION, INSTRUMENT
PANEL END.........................23-68
CAP - OPERATION, FUEL FILLER........25-12
CAP - OPERATION, RADIATOR
PRESSURE
..........................7-27
CAP - REMOVAL, INSTRUMENT PANEL
END
...............................23-68
CAP TESTING - DIAGNOSIS AND
TESTING, COOLING SYSTEM
PRESSURE
..........................7-27
CAP TO FILLER NECK SEAL -
DIAGNOSIS AND TESTING, RADIATOR
.....7-27
CAPACITIES - SPECIFICATIONS, FLUID
......0-6CARE - CLEANING, ALUMINUM WHEEL . . . 22-18
CARGO - INSTALLATION, AWD, HEAVY
DUTY...............................2-36
CARGO - INSTALLATION, SPRING........2-40
CARGO - REMOVAL, AWD, HEAVY DUTY . . . 2-36
CARGO - REMOVAL, SPRING............2-40
CARPETS AND FLOOR MATS -
INSTALLATION.......................23-76
CARPETS AND FLOOR MATS - REMOVAL . 23-75
CARRIER ASSEMBLY - DESCRIPTION,
BALANCE SHAFTS.....................9-69
CARRIER ASSEMBLY - INSTALLATION,
BALANCE SHAFTS.....................9-72
CARRIER ASSEMBLY - OPERATION,
BALANCE SHAFTS.....................9-69
CARRIER ASSEMBLY - REMOVAL,
BALANCE SHAFTS.....................9-69
CARRIER SEAL - INSTALLATION,
DIFFERENTIAL........................21-9
CARRIER SEAL - REMOVAL,
DIFFERENTIAL........................21-9
CATALYTIC CONVERTER - DESCRIPTION . . . 11-4
CATALYTIC CONVERTER - INSPECTION....11-5
CATALYTIC CONVERTER - INSTALLATION . . . 11-6
CATALYTIC CONVERTER - OPERATION.....11-4
CATALYTIC CONVERTER - REMOVAL......11-5
CAUSES - DIAGNOSIS AND TESTING,
COMMON PROBLEM..................21-30
CAUTION - A/C SYSTEM...............24-66
CAUTION - CAUTIONS...................5-78
CAUTION, DESCRIPTION.............5-4,5s-4
CAUTION, DESCRIPTION...............19-37
CAUTION, SENSOR - TPM.........22-10,22s-2
CAUTIONS, CAUTION..................5-78
CAUTIONS, WARNING - WARNINGS . 19-10,19-27
CD CHANGER - DESCRIPTION...........8A-7
CD CHANGER - INSTALLATION...........8A-8
CD CHANGER - OPERATION.............8A-7
CD CHANGER - REMOVAL..............8A-8
CENTER - DESCRIPTION, ELECTRONIC
VEHICLE INFO.......................8M-6
CENTER - DIAGNOSIS AND TESTING,
ELECTRONIC VEHICLE INFORMATION.....8M-7
CENTER - INSTALLATION, ELECTRONIC
VEHICLE INFO.......................8M-9
CENTER - OPERATION, ELECTRONIC
VEHICLE INFO.......................8M-7
CENTER - REMOVAL, ELECTRONIC
VEHICLE INFO.......................8M-9
CENTER BEZEL - INSTALLATION,
INSTRUMENT PANEL..................23-68
CENTER BEZEL - REMOVAL,
INSTRUMENT PANEL..................23-68
CENTER BEZEL OUTLETS -
INSTALLATION.......................24-45
CENTER BEZEL OUTLETS - REMOVAL....24-44
CENTER CONSOLE LAMP -
INSTALLATION.......................8L-21
CENTER CONSOLE LAMP - REMOVAL....8L-21
CENTER CONSOLE LAMP SWITCH -
INSTALLATION.......................8L-21
CENTER CONSOLE LAMP SWITCH -
REMOVAL..........................8L-21
CENTER HIGH MOUNTED STOP LAMP -
INSTALLATION........................8L-6
CENTER HIGH MOUNTED STOP LAMP -
REMOVAL...........................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION..................8L-6
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL.....................8L-6
CENTER HINGE - INSTALLATION.........23-24
CENTER HINGE - REMOVAL............23-24
CENTER PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION.......................8M-7
CENTER STRIKER - INSTALLATION.......23-28
CENTER STRIKER - REMOVAL..........23-28
CENTERING - STANDARD PROCEDURE,
CLOCK SPRING.......................8O-5
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE
.........................Intro.-11
CHAIN AND CAMSHAFT SPROCKET -
INSTALLATION, TIMING
................9-157
CHAIN AND CAMSHAFT SPROCKET -
REMOVAL, TIMING
...................9-156
CHAIN COVER - INSTALLATION, TIMING
. . 9-155
CHAIN COVER - REMOVAL, TIMING
......9-153
6 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

DISC BRAKE CALIPER GUIDE PINS (TRW
BRAKES) - INSTALLATION..............5s-30
DISC BRAKE CALIPER GUIDE PINS (TRW
BRAKES) - REMOVAL.................5s-30
DISC BRAKE CALIPER (TRW BRAKES) -
INSTALLATION, FRONT................5s-26
DISC BRAKE CALIPER (TRW BRAKES) -
REMOVAL, FRONT....................5s-23
DISC BRAKE SHOES - CLEANING....5-16,5-18,
5s-15,5s-17
DISC BRAKE SHOES - INSPECTION . . . 5-16,5-18,
5s-15,5s-17
DISC BRAKE SHOES - INSTALLATION,
REAR..........................5-19,5s-18
DISC BRAKE SHOES - REMOVAL, REAR . . . 5-17,
5s-16
DISC BRAKE SHOES (CONTINENTAL
TEVES BRAKES) - INSTALLATION,
FRONT.............................5s-15
DISC BRAKE SHOES (CONTINENTAL
TEVES BRAKES) - REMOVAL, FRONT.....5s-14
DISC BRAKE SHOES (DISC/DISC
BRAKES) - INSTALLATION, FRONT........5-16
DISC BRAKE SHOES (DISC/DISC
BRAKES) - REMOVAL, FRONT............5-14
DISC BRAKE SHOES (DISC/DRUM
BRAKES) - INSTALLATION, FRONT........5-17
DISC BRAKE SHOES (DISC/DRUM
BRAKES) - REMOVAL, FRONT............5-15
DISC BRAKE SHOES (TRW BRAKES) -
INSTALLATION, FRONT................5s-16
DISC BRAKE SHOES (TRW BRAKES) -
REMOVAL, FRONT....................5s-14
DISC BRAKES (EXPORT) - DESCRIPTION....5-13,
5s-12
DISC BRAKES (FRONT) - DESCRIPTION . . . 5-11,
5s-10
DISC BRAKES (FRONT) - OPERATION . 5-13,5s-12
DISC BRAKES (REAR) - DESCRIPTION....5-12,
5s-12
DISC BRAKES (REAR) - OPERATION . . 5-13,5s-13
DISC RUNOUT - DIAGNOSIS AND
TESTING, CLUTCH COVER...............6-6
DISCHARGE (ESD) SENSITIVE DEVICES -
STANDARD PROCEDURE,
ELECTROSTATIC...................8W-01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-80
DISCHARGE LINE - REMOVAL, A/C.......24-79
DISPLAY TEST MODE, OPERATION - DRB
IIITSTATE ...........................25-9
DISSASEMBLY, REMOVAL..............24-51
DISTRIBUTION DUCT - INSTALLATION....24-57
DISTRIBUTION DUCT - REMOVAL........24-57
DISTRIBUTION DUCTS - INSTALLATION,
FLOOR.............................24-50
DISTRIBUTION DUCTS - REMOVAL,
FLOOR.............................24-50
DISTRIBUTION SYSTEM - DESCRIPTION,
POWER..........................8W-97-1
DISTRIBUTION SYSTEM - OPERATION,
POWER..........................8W-97-1
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER...................8W-97-1
DOES NOT FILL - DIAGNOSIS AND
TESTING, VEHICLE...................25-16
DOME/CARGO LAMP - INSTALLATION....8L-22
DOME/CARGO LAMP - REMOVAL........8L-22
DOOR - INSTALLATION................23-16
DOOR - INSTALLATION, FUEL FILL.......23-52
DOOR - INSTALLATION, SLIDING........23-30
DOOR - REMOVAL....................23-15
DOOR - REMOVAL, FUEL FILL..........23-52
DOOR - REMOVAL, SLIDING............23-29
DOOR ACTUATOR - DESCRIPTION,
BLEND........................24-23,24-35
DOOR ACTUATOR - DESCRIPTION,
MODE.............................24-30
DOOR ACTUATOR - DESCRIPTION,
RECIRCULATION.....................24-32
DOOR ACTUATOR - INSTALLATION,
BLEND
........................24-23,24-36
DOOR ACTUATOR - INSTALLATION,
MODE
.............................24-31
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION
.....................24-33
DOOR ACTUATOR - OPERATION, BLEND
. . 24-23,
24-35
DOOR ACTUATOR - OPERATION, MODE
. . . 24-30DOOR ACTUATOR - OPERATION,
RECIRCULATION.....................24-32
DOOR ACTUATOR - REAR -
DESCRIPTION, MODE.................24-39
DOOR ACTUATOR - REAR -
INSTALLATION, MODE.................24-40
DOOR ACTUATOR - REAR - OPERATION,
MODE.............................24-40
DOOR ACTUATOR - REAR - REMOVAL,
MODE.............................24-40
DOOR ACTUATOR - REMOVAL, BLEND . . . 24-23,
24-36
DOOR ACTUATOR - REMOVAL, MODE....24-30
DOOR ACTUATOR - REMOVAL,
RECIRCULATION.....................24-33
DOOR ADJUSTMENT - STANDARD
PROCEDURE, SLIDING................8N-28
DOOR ADJUSTMENTS, ADJUSTMENTS -
SLIDING............................23-30
DOOR BLOCKER LATCH - INSTALLATION,
FUEL FILL..........................23-53
DOOR BLOCKER LATCH - REMOVAL,
FUEL FILL..........................23-53
DOOR BLOCKER LATCH STRIKER -
INSTALLATION, FUEL FILL.............23-53
DOOR BLOCKER LATCH STRIKER -
REMOVAL, FUEL FILL.................23-53
DOOR BLOCKER LOCKOUT LINK -
INSTALLATION, FUEL FILL.............23-54
DOOR BLOCKER LOCKOUT LINK -
REMOVAL, FUEL FILL.................23-53
DOOR CONTROL MODULE -
DESCRIPTION, SLIDING...............8E-19
DOOR CONTROL MODULE -
INSTALLATION, SLIDING...............8E-20
DOOR CONTROL MODULE - OPERATION,
SLIDING............................8E-19
DOOR CONTROL MODULE - REMOVAL,
SLIDING............................8E-19
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION.......................8N-40
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS AND TESTING.............8N-40
DOOR CYLINDER LOCK SWITCH -
EXPORT - DESCRIPTION................8N-3
DOOR CYLINDER LOCK SWITCH -
EXPORT - DIAGNOSIS AND TESTING......8N-3
DOOR CYLINDER LOCK SWITCH -
EXPORT - INSTALLATION...............8N-4
DOOR CYLINDER LOCK SWITCH -
EXPORT - OPERATION.................8N-3
DOOR CYLINDER LOCK SWITCH -
EXPORT - REMOVAL...................8N-3
DOOR CYLINDER LOCK SWITCH -
INSTALLATION......................8N-41
DOOR CYLINDER LOCK SWITCH -
OPERATION.........................8N-40
DOOR CYLINDER LOCK SWITCH -
REMOVAL..........................8N-41
DOOR GLASS - INSTALLATION..........23-17
DOOR GLASS - INSTALLATION, REAR . . . 23-111
DOOR GLASS - INSTALLATION, SLIDING . 23-110
DOOR GLASS - REMOVAL.............23-17
DOOR GLASS - REMOVAL, REAR.......23-111
DOOR GLASS - REMOVAL, SLIDING.....23-110
DOOR GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT...............23-113
DOOR GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT...................23-113
DOOR INNER BELT MOLDING -
INSTALLATION, FRONT...............23-115
DOOR INNER BELT MOLDING -
REMOVAL, FRONT...................23-115
DOOR LEARN CYCLE - STANDARD
PROCEDURE, POWER.................8N-28
DOOR LOCK MOTOR - DIAGNOSIS AND
TESTING.......................8N-4,8N-41
DOOR LOCK MOTOR - INSTALLATION,
SLIDING.......................8N-44,8N-6
DOOR LOCK MOTOR - REMOVAL,
SLIDING.......................8N-44,8N-6
DOOR LOCK SWITCH - DIAGNOSIS AND
TESTING
.......................8N-4,8N-41
DOOR LOCK SWITCH - INSTALLATION
....8N-4,
8N-42
DOOR LOCK SWITCH - REMOVAL
. . . 8N-4,8N-42
DOOR MOTOR - DESCRIPTION, SLIDING
. . 8N-30
DOOR MOTOR - INSTALLATION, SLIDING
. 8N-31DOOR MOTOR - OPERATION, SLIDING . . . 8N-30
DOOR MOTOR - REMOVAL, SLIDING.....8N-30
DOOR OUTER BELT MOLDING -
INSTALLATION, FRONT...............23-113
DOOR OUTER BELT MOLDING -
REMOVAL, FRONT...................23-113
DOOR SILL PLATE - INSTALLATION,
SLIDING............................23-82
DOOR SILL PLATE - REMOVAL, SLIDING . . 23-82
DOOR SILL TRIM PLATE -
INSTALLATION.......................23-77
DOOR SILL TRIM PLATE - REMOVAL.....23-77
DOOR STOP BUMPER BEZEL -
INSTALLATION, SLIDING...............23-25
DOOR STOP BUMPER BEZEL -
REMOVAL, SLIDING..................23-25
DOOR SYSTEM - DESCRIPTION, POWER
SLIDING...........................8N-19
DOOR SYSTEM - DIAGNOSIS AND
TESTING, POWER SLIDING.............8N-22
DOOR SYSTEM - OPERATION, POWER
SLIDING...........................8N-21
DOOR WEATHERSTRIP - INSTALLATION,
FRONT............................23-114
DOOR WEATHERSTRIP - INSTALLATION,
SLIDING...........................23-115
DOOR WEATHERSTRIP - REMOVAL,
FRONT............................23-114
DOOR WEATHERSTRIP - REMOVAL,
SLIDING...........................23-115
DOSING PUMP - DESCRIPTION, FUEL . . . 24-115
DOSING PUMP - INSTALLATION, FUEL....24-116
DOSING PUMP - OPERATION, FUEL.....24-115
DOSING PUMP - REMOVAL, FUEL......24-115
DOWNSTREAM 1/2 - 2.4/3.3/3.8L -
REMOVAL..........................14-34
DOWNSTREAM 2/1, 2.4/3.3/3.8L -
INSTALLATION.......................14-34
D-PILLAR TRIM PANEL - INSTALLATION,
LEFT..............................23-78
D-PILLAR TRIM PANEL - INSTALLATION,
RIGHT.............................23-82
D-PILLAR TRIM PANEL - REMOVAL,
LEFT..............................23-78
D-PILLAR TRIM PANEL - REMOVAL,
RIGHT.............................23-81
DRAIN AND FILL - STANDARD
PROCEDURE, FLUID..................21-71
DRAIN TUBE - INSTALLATION..........23-120
DRAIN TUBE - REMOVAL.............23-119
DRAINCOCK - INSTALLATION, RADIATOR . . . 7-26
DRAINCOCK - REMOVAL, RADIATOR......7-26
DRAINING - STANDARD PROCEDURE,
COOLING SYSTEM.....................7-4
DRAINING FUEL TANK - STANDARD
PROCEDURE.........................14-2
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-13
DRB IIITSTATE DISPLAY TEST MODE,
OPERATION..........................25-9
DRIER - DESCRIPTION, RECEIVER.......24-91
DRIER - INSTALLATION, RECEIVER......24-92
DRIER - OPERATION, RECEIVER.........24-91
DRIER - REMOVAL, RECEIVER..........24-91
DRIVE - ASSEMBLY, FINAL......21-195,21s-99
DRIVE - DESCRIPTION, FINAL..........21s-95
DRIVE - DESCRIPTION, FLEX...........8N-36
DRIVE - DISASSEMBLY, FINAL . . . 21-190,21s-96
DRIVE - INSTALLATION, FLEX..........8N-37
DRIVE - OPERATION, FINAL...........21s-96
DRIVE - OPERATION, FLEX.............8N-36
DRIVE - REMOVAL, FLEX..............8N-37
DRIVE BELT - DIAGNOSIS AND TESTING,
ACCESSORY..........................7-7
DRIVE BELT TENSION, SPECIFICATIONS -
ACCESSORY..........................7-5
DRIVE BELTS - 2.4L - ADJUSTMENTS.....7-10
DRIVE BELTS - 2.4L - CLEANING..........7-9
DRIVE BELTS - 2.4L - INSPECTION........7-9
DRIVE BELTS - 2.4L - INSTALLATION......7-10
DRIVE BELTS - 2.4L - REMOVAL..........7-8
DRIVE BELTS - 3.3/3.8L - CLEANING......7-11
DRIVE BELTS - 3.3/3.8L - INSPECTION
....7-11
DRIVE BELTS - 3.3/3.8L - INSTALLATION
. . . 7-12
DRIVE BELTS - 3.3/3.8L - REMOVAL
......7-11
DRIVE PLATE MISALIGNMENT -
DIAGNOSIS AND TESTING
...............6-6
DRIVE UNIT - DESCRIPTION, LOWER
....8N-32
RSINDEX11
Description Group-Page Description Group-Page Description Group-Page

ENGINE OIL LEVEL CHECK, STANDARD
PROCEDURE.........................9-53
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING.......................9-136
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING, CHECKING...............9-52
ENGINE, SPECIAL TOOLS - 2.4L..........9-21
ENGINE, SPECIAL TOOLS - 3.3/3.8L.......9-95
ENGINE, SPECIFICATIONS - 3.3/3.8L . . 9-91,9s-11
ENGINE SPEED SENSOR - DESCRIPTION . . 14-26
ENGINE SPEED SENSOR - OPERATION....14-26
ENGINES - DESCRIPTION, ENGINE OIL -
DIESEL..............................0-6
ENGINES - DIAGNOSIS AND TESTING,
SYSTEM CHARGE LEVEL TEST -
GASOLINE..........................24-67
ENGINES - EXPORT - DESCRIPTION,
DIESEL.............................0-24
ENTRY MODULE - DESCRIPTION,
REMOTE KEYLESS...................8N-43
ENTRY MODULE - DESCRIPTION,
SENTRY KEY REMOTE.................8Q-3
ENTRY MODULE - DIAGNOSIS AND
TESTING, REMOTE KEYLESS...........8N-43
ENTRY MODULE - DIAGNOSIS AND
TESTING, SENTRY KEY REMOTE.........8Q-5
ENTRY MODULE - INSTALLATION,
REMOTE KEYLESS...................8N-44
ENTRY MODULE - INSTALLATION,
SENTRY KEY REMOTE.................8Q-6
ENTRY MODULE - OPERATION, REMOTE
KEYLESS...........................8N-43
ENTRY MODULE - OPERATION, SENTRY
KEY REMOTE........................8Q-4
ENTRY MODULE - REMOVAL, REMOTE
KEYLESS...........................8N-44
ENTRY MODULE - REMOVAL, SENTRY
KEY REMOTE........................8Q-5
ENTRY SYSTEM - DIAGNOSIS AND
TESTING, SENTRY KEY REMOTE.........8Q-3
ENTRY TRANSMITTER - DIAGNOSIS AND
TESTING, KEYLESS..............8N-42,8N-5
ENTRY TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE, REMOTE
KEYLESS............................8N-5
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-70
ERASING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-11
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-72
EVAP CANISTER - INSTALLATION, REAR . . 25-20
EVAP CANISTER - REMOVAL, REAR......25-19
EVAPORATION CONTROL SYSTEM -
OPERATION.........................25-10
EVAPORATOR - DESCRIPTION, A/C . 24-80,24-97
EVAPORATOR - INSTALLATION, A/C......24-80
EVAPORATOR - INSTALLATION, REAR
A/C................................24-99
EVAPORATOR - OPERATION, A/C . . . 24-80,24-97
EVAPORATOR - REMOVAL, A/C..........24-80
EVAPORATOR - REMOVAL, REAR A/C.....24-97
EVAPORATOR LINE EXTENSION -
INSTALLATION, REAR A/C..............24-99
EVAPORATOR LINE EXTENSION -
REMOVAL, A/C......................24-98
EVAPORATOR TEMPERATURE SENSOR -
DESCRIPTION.......................24-27
EVAPORATOR TEMPERATURE SENSOR -
OPERATION.........................24-28
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-12
EVAP/PURGE SOLENOID - INSTALLATION . 25-12
EVAP/PURGE SOLENOID - OPERATION....25-12
EVAP/PURGE SOLENOID - REMOVAL.....25-12
EXCESSIVE EXHAUST SYSTEM NOISE -
DIAGNOSIS AND TESTING..............11-2
EXHAUST MANIFOLD - CLEANING........9-61
EXHAUST MANIFOLD - INSPECTION.......9-61
EXHAUST MANIFOLD - INSTALLATION.....9-61
EXHAUST MANIFOLD - LEFT - CLEANING . . 9-152
EXHAUST MANIFOLD - LEFT -
INSPECTION
........................9-152
EXHAUST MANIFOLD - LEFT -
INSTALLATION
.......................9-152
EXHAUST MANIFOLD - LEFT - REMOVAL
. . 9-152
EXHAUST MANIFOLD - REMOVAL
.........9-61
EXHAUST MANIFOLD - RIGHT -
CLEANING
..........................9-151EXHAUST MANIFOLD - RIGHT -
INSPECTION........................9-151
EXHAUST MANIFOLD - RIGHT -
INSTALLATION.......................9-151
EXHAUST MANIFOLD - RIGHT -
REMOVAL..........................9-150
EXHAUST SYSTEM - DESCRIPTION.......11-1
EXHAUST SYSTEM NOISE - DIAGNOSIS
AND TESTING, EXCESSIVE..............11-2
EXHAUST SYSTEM RESTRICTION CHECK
- DIAGNOSIS AND TESTING.............11-2
EXHAUST SYSTEM, SPECIAL TOOLS......11-4
EXHAUST TUBE - INSTALLATION.......24-115
EXHAUST TUBE - REMOVAL...........24-114
EXHAUSTER - DESCRIPTION, REAR
QUARTER PANEL/FENDER AIR..........23-57
EXHAUSTER - INSTALLATION, REAR
QUARTER PANEL/FENDER AIR..........23-58
EXHAUSTER - REMOVAL, REAR
QUARTER PANEL/FENDER AIR..........23-57
EXPANSION VALVE - DESCRIPTION......24-81
EXPANSION VALVE - DESCRIPTION, A/C . . 24-99
EXPANSION VALVE - DIAGNOSIS AND
TESTING..........................24-100
EXPANSION VALVE - DIAGNOSIS AND
TESTING, A/C.......................24-81
EXPANSION VALVE - INSTALLATION......24-82
EXPANSION VALVE - INSTALLATION, A/C . 24-100
EXPANSION VALVE - OPERATION........24-81
EXPANSION VALVE - OPERATION, A/C....24-99
EXPANSION VALVE - REMOVAL.........24-82
EXPANSION VALVE - REMOVAL, A/C.....24-100
EXPORT - BRAKE ROTOR..........5-55,5s-58
EXPORT - DESCRIPTION...........5-58,5s-60
EXPORT - DESCRIPTION................0-15
EXPORT - DESCRIPTION................2-10
EXPORT - DESCRIPTION, ANTENNA
MODULE............................8A-6
EXPORT - DESCRIPTION, DIESEL
ENGINES............................0-24
EXPORT - DESCRIPTION, DOOR
CYLINDER LOCK SWITCH...............8N-3
EXPORT - DESCRIPTION, POWER
FOLDAWAY MIRROR SWITCH..........8N-48
EXPORT - DESCRIPTION, QUARTER
GLASS INTEGRAL ANTENNA.............8A-9
EXPORT - DIAGNOSIS AND TESTING,
ANTENNA MODULE....................8A-7
EXPORT - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK SWITCH.........8N-3
EXPORT - DIAGNOSIS AND TESTING,
QUARTER GLASS INTEGRAL ANTENNA....8A-9
EXPORT - INSTALLATION...............2-11
EXPORT - INSTALLATION, ANTENNA
MODULE............................8A-7
EXPORT - INSTALLATION, DOOR
CYLINDER LOCK SWITCH...............8N-4
EXPORT - INSTALLATION, HEADLAMP
UNIT..............................8L-17
EXPORT - INSTALLATION, HOOD AJAR
SWITCH............................8Q-3
EXPORT - INSTALLATION, POWER
FOLDAWAY MIRROR SWITCH..........8N-49
EXPORT - OPERATION, ANTENNA
MODULE............................8A-6
EXPORT - OPERATION, DOOR CYLINDER
LOCK SWITCH........................8N-3
EXPORT - OPERATION, POWER
FOLDAWAY MIRROR SWITCH..........8N-48
EXPORT - OPERATION, QUARTER GLASS
INTEGRAL ANTENNA...................8A-9
EXPORT - REMOVAL...................2-11
EXPORT - REMOVAL, ANTENNA MODULE . . 8A-7
EXPORT - REMOVAL, DOOR CYLINDER
LOCK SWITCH........................8N-3
EXPORT - REMOVAL, HEADLAMP UNIT . . . 8L-17
EXPORT - REMOVAL, HOOD AJAR
SWITCH............................8Q-3
EXPORT - REMOVAL, POWER
FOLDAWAY MIRROR SWITCH
..........8N-48
EXPORT - STANDARD PROCEDURE,
FRONT FOG LAMP UNIT ALIGNMENT
......8L-9
EXPORT - STANDARD PROCEDURE,
HEADLAMP UNIT ALIGNMENT
..........8L-14
EXTENSION - INSTALLATION, REAR A/C
EVAPORATOR LINE
...................24-99
EXTENSION - REMOVAL, A/C
EVAPORATOR LINE
...................24-98EXTENSION TRIM - INSTALLATION,
A-PILLAR LOWER....................23-74
EXTENSION TRIM - REMOVAL, A-PILLAR
LOWER............................23-74
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - WARNING, LAMPS/
LIGHTING...........................8L-3
EXTERIOR HANDLE - INSTALLATION.....23-22,
23-40
EXTERIOR HANDLE - REMOVAL....23-21,23-40
EXTERIOR HANDLE SWITCH -
DESCRIPTION.......................8N-11
EXTERIOR HANDLE SWITCH -
INSTALLATION......................8N-12
EXTERIOR HANDLE SWITCH -
OPERATION.........................8N-11
EXTERIOR HANDLE SWITCH - REMOVAL . . 8N-11
EXTERIOR LAMPS, SPECIFICATIONS......8L-3
EXTERIOR NAME PLATES - ADHESIVE
ATTACHED - INSTALLATION............23-51
EXTERIOR NAME PLATES - ADHESIVE
ATTACHED - REMOVAL................23-51
EXTERIOR NAME PLATES - TAPE
ATTACHED - INSTALLATION............23-51
EXTERIOR NAME PLATES - TAPE
ATTACHED - REMOVAL................23-51
FACTOR SETTING - STANDARD
PROCEDURE, PINION............8E-15,8E-23
FAILED PARK SWITCH - DIAGNOSIS AND
TESTING..............................8R-2
FAN - DESCRIPTION, RADIATOR..........7-28
FAN - INSTALLATION, RADIATOR.........7-30
FAN - OPERATION, RADIATOR...........7-29
FAN - REMOVAL, RADIATOR.............7-30
FAN MOTOR - DIAGNOSIS AND
TESTING, RADIATOR...................7-29
FAN RELAY - DESCRIPTION, RADIATOR....7-30
FAN RELAY - INSTALLATION, RADIATOR . . . 7-30
FAN RELAY - OPERATION, RADIATOR......7-30
FAN RELAY - REMOVAL, RADIATOR.......7-30
FASCIA - INSTALLATION, FRONT.........13-1
FASCIA - INSTALLATION, REAR..........13-2
FASCIA - REMOVAL, FRONT.............13-1
FASCIA - REMOVAL, REAR..............13-2
FASCIA - SCUFF PAD - INSTALLATION,
REAR...............................13-4
FASCIA - SCUFF PAD - REMOVAL, REAR . . . 13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-2
FASTENER TORQUE, SPECIFICATIONS -
ABS ................................5-79
FASTENER TORQUE, SPECIFICATIONS -
BRAKE...........................5-9,5s-8
FASTENER TORQUE, SPECIFICATIONS -
FRONT SUSPENSION...................2-3
FASTENER TORQUE, SPECIFICATIONS -
POWER STEERING....................19-9
FASTENER TORQUE, SPECIFICATIONS -
REAR SUSPENSION...................2-28
FASTENER USAGE - DESCRIPTION......Intro.-5
FEED CIRCUIT RESISTANCE TEST -
DIAGNOSIS AND TESTING.........8F-32,8F-34
FEED CIRCUIT TEST - DIAGNOSIS AND
TESTING
......................8F-33,8F-35
FENDER - INSTALLATION, FRONT
........23-52
FENDER - REMOVAL, FRONT
...........23-52
FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES NOT
..................25-16
FILL - STANDARD PROCEDURE, FLUID
DRAIN
.............................21-71
FILL DOOR - INSTALLATION, FUEL
.......23-52
FILL DOOR - REMOVAL, FUEL
..........23-52
FILL DOOR BLOCKER LATCH -
INSTALLATION, FUEL
.................23-53
FILL DOOR BLOCKER LATCH -
REMOVAL, FUEL
.....................23-53
FILL DOOR BLOCKER LATCH STRIKER -
INSTALLATION, FUEL
.................23-53
FILL DOOR BLOCKER LATCH STRIKER -
REMOVAL, FUEL
.....................23-53
FILL DOOR BLOCKER LOCKOUT LINK -
INSTALLATION, FUEL
.................23-54
FILL DOOR BLOCKER LOCKOUT LINK -
REMOVAL, FUEL
.....................23-53
RSINDEX13
Description Group-Page Description Group-Page Description Group-Page

FILL/CHECK LOCATIONS - DESCRIPTION,
FLUID...............................0-7
FILLER CAP - DESCRIPTION, FUEL.......25-12
FILLER CAP - OPERATION, FUEL........25-12
FILLER NECK SEAL - DIAGNOSIS AND
TESTING, RADIATOR CAP TO............7-27
FILLER TUBE - INSTALLATION, FUEL
TANK ..............................14-13
FILLER TUBE - REMOVAL, FUEL TANK....14-12
FILLING - STANDARD PROCEDURE,
COOLING SYSTEM.....................7-5
FILLING - STANDARD PROCEDURE,
REAR HEATER CORE.................24-101
FILTER - DESCRIPTION, AIR............24-43
FILTER - DESCRIPTION, OIL.............9-53
FILTER - INSTALLATION, AIR...........24-44
FILTER - INSTALLATION, INLET..........14-13
FILTER - INSTALLATION, OIL.......9-139,9-53
FILTER - REMOVAL, AIR...............24-43
FILTER - REMOVAL, INLET.............14-13
FILTER - REMOVAL, OIL...........9-139,9-53
FILTER ADAPTER - INSTALLATION, OIL . . . 9-139
FILTER ADAPTER - REMOVAL, OIL.......9-139
FILTER CHANGE - STANDARD
PROCEDURE, ENGINE OIL..........9-137,9-53
FILTER SERVICE - STANDARD
PROCEDURE, FLUID..........21-203,21s-104
FINAL DRIVE - ASSEMBLY......21-195,21s-99
FINAL DRIVE - DESCRIPTION............21s-95
FINAL DRIVE - DISASSEMBLY....21-190,21s-96
FINAL DRIVE - OPERATION............21s-96
FINESSE SANDING/BUFFING &
POLISHING - DESCRIPTION............23-85
FINISH - DESCRIPTION, BASE
COAT/CLEARCOAT....................23-85
FIRING ORDER, SPECIFICATIONS.........8I-3
FIRST ROW - BENCH - INSTALLATION,
SEAT BELT BUCKLE..................8O-13
FIRST ROW - BENCH - REMOVAL, SEAT
BELT BUCKLE.......................8O-13
FIRST ROW - OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-14
FIRST ROW - OUTBOARD - REMOVAL,
SEAT BELT & RETRACTOR.............8O-14
FIRST ROW INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE......8O-12
FIRST ROW INBOARD - QUAD BUCKET -
REMOVAL, SEAT BELT BUCKLE.........8O-12
FITTING - CONNECTING ROD............9-45
FITTING - PISTON RING................9-45
FITTING - STANDARD PROCEDURE,
MAIN BEARING......................9-123
FITTING - STANDARD PROCEDURE,
PISTON RING.......................9-121
FITTING - STANDARD PROCEDURE,
PISTON TO CYLINDER BORE............9-42
FITTING CONNECTING RODS -
STANDARD PROCEDURE...............9-116
FITTING PISTONS - STANDARD
PROCEDURE........................9-117
FITTINGS - STANDARD PROCEDURE,
HANDLING TUBING...................24-70
FITTINGS - STANDARD PROCEDURE,
QUICK-CONNECT.....................14-14
FLANGE SEAL - INSTALLATION, INPUT....3-45
FLANGE SEAL - INSTALLATION, OUTPUT . . . 3-46
FLANGE SEAL - REMOVAL, INPUT
........3-44
FLANGE SEAL - REMOVAL, OUTPUT
.......3-45
FLANGE SHIM SELECTION,
ADJUSTMENTS - OUTPUT
...............21-7
FLAP AND SPRING ASSEMBLY -
INSTALLATION, QUAD BUCKET SEAT
SIDE SHIELD/CUPHOLDER
............23-107
FLAP AND SPRING ASSEMBLY -
REMOVAL, QUAD BUCKET SEAT SIDE
SHIELD/CUPHOLDER
.................23-107
FLEX DRIVE - DESCRIPTION
...........8N-36
FLEX DRIVE - INSTALLATION
...........8N-37
FLEX DRIVE - OPERATION
.............8N-36
FLEX DRIVE - REMOVAL
...............8N-37
FLEX PLATE - INSTALLATION
...........9-131
FLEX PLATE - REMOVAL
...............9-131
FLEXIBLE FUEL ENGINE OIL -
DESCRIPTION
.........................0-3
FLOOR CONSOLE TRAY - BRACKET
ASSEMBLY - INSTALLATION
............23-83FLOOR CONSOLE TRAY - BRACKET
ASSEMBLY - REMOVAL................23-83
FLOOR CONSOLE TRAY - INSTALLATION . . 23-83
FLOOR CONSOLE TRAY - REMOVAL......23-83
FLOOR DISTRIBUTION DUCTS -
INSTALLATION.......................24-50
FLOOR DISTRIBUTION DUCTS -
REMOVAL..........................24-50
FLOOR HEAT DUCT - INSTALLATION,
REAR..............................24-63
FLOOR HEAT DUCT - REMOVAL, REAR . . . 24-62
FLOOR MATS - INSTALLATION, CARPETS . 23-76
FLOOR MATS - REMOVAL, CARPETS.....23-75
FLOW AND PRESSURE TEST -
DIAGNOSIS AND TESTING, POWER
STEERING SYSTEM....................19-1
FLOW CHECK - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-3
FLUID - DESCRIPTION, AUTOMATIC/
MANUAL TRANSAXLE...................0-4
FLUID - DESCRIPTION, AWD POWER
TRANSFER UNIT.......................0-6
FLUID AND FILTER SERVICE -
STANDARD PROCEDURE.......21-203,21s-104
FLUID CAPACITIES - SPECIFICATIONS......0-6
FLUID CHANGE - STANDARD
PROCEDURE, DIFFERENTIAL
ASSEMBLY..........................3-40
FLUID CHANGE - STANDARD
PROCEDURE, OVERRUNNING CLUTCH
HOUSING............................3-41
FLUID CHANGE - STANDARD
PROCEDURE, PTU......................21-5
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE.............5-32,5s-31
FLUID COOLER - DESCRIPTION.........19-44
FLUID COOLER - INSTALLATION.........19-45
FLUID COOLER - OPERATION...........19-44
FLUID COOLER - REMOVAL............19-44
FLUID DRAIN AND FILL - STANDARD
PROCEDURE........................21-71
FLUID FILL/CHECK LOCATIONS -
DESCRIPTION.........................0-7
FLUID LEAK DIAGNOSIS, DIAGNOSIS
AND TESTING........................21-3
FLUID LEAKAGE - DIAGNOSIS AND
TESTING, TORQUE CONVERTER
HOUSING....................21-123,21s-31
FLUID LEVEL AND CONDITION CHECK,
STANDARD PROCEDURE.......21-201,21s-102
FLUID LEVEL CHECK - STANDARD
PROCEDURE........................21-71
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, BRAKE..............5-32,5s-31
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING........19-44
FLUID LEVEL INSPECTION - STANDARD
PROCEDURE.........................21-4
FLUID LEVEL SWITCH - DESCRIPTION,
BRAKE..........................5-10,5s-9
FLUID LEVEL SWITCH - INSTALLATION,
BRAKE.........................5-11,5s-10
FLUID LEVEL SWITCH - INSTALLATION,
WASHER...........................8R-12
FLUID LEVEL SWITCH - OPERATION,
BRAKE..........................5-10,5s-9
FLUID LEVEL SWITCH - REMOVAL,
BRAKE
.........................5-11,5s-10
FLUID LEVEL SWITCH - REMOVAL,
WASHER
...........................8R-12
FLUID, SPECIFICATIONS - BRAKE
....5-33,5s-32
FLUIDS - DESCRIPTION, AWD REAR
DRIVELINE MODULE
....................0-6
FLUSH MEASUREMENTS -
SPECIFICATIONS, GAP
................23-124
FLYWHEEL - INSTALLATION
.............6-12
FLYWHEEL - REMOVAL
.................6-12
FOG LAMP - DIAGNOSIS AND TESTING,
FRONT
..............................8L-7
FOG LAMP - INSTALLATION, FRONT
.......8L-8
FOG LAMP - REMOVAL, FRONT
..........8L-8
FOG LAMP UNIT ALIGNMENT - EXPORT
- STANDARD PROCEDURE, FRONT
........8L-9
FOG LAMP UNIT ALIGNMENT -
STANDARD PROCEDURE, FRONT
.........8L-9
FOLDAWAY MIRROR SWITCH - EXPORT
- DESCRIPTION, POWER
..............8N-48FOLDAWAY MIRROR SWITCH - EXPORT
- INSTALLATION, POWER..............8N-49
FOLDAWAY MIRROR SWITCH - EXPORT
- OPERATION, POWER................8N-48
FOLDAWAY MIRROR SWITCH - EXPORT
- REMOVAL, POWER..................8N-48
FORK AND SHAFT - DESCRIPTION,
SHIFT.............................21-113
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . . 9-11,9-84
FRAME DIMENSIONS, SPECIFICATIONS....13-4
FRONT - DESCRIPTION, HALF SHAFT.......3-1
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.......................9-127,9-40
FRONT - INSTALLATION, HALF SHAFT......3-4
FRONT - INSTALLATION, SEAT BELT &
RETRACTOR - OUTBOARD.............8O-14
FRONT - INSTALLATION, SPRING
MOUNTS............................2-44
FRONT - INSTALLATION, WHEEL
MOUNTING STUDS...................22-21
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL..........................9-127,9-40
FRONT - REMOVAL, HALF SHAFT..........3-2
FRONT - REMOVAL, SEAT BELT &
RETRACTOR - OUTBOARD.............8O-14
FRONT - REMOVAL, SPRING MOUNTS.....2-43
FRONT - REMOVAL, WHEEL MOUNTING
STUDS.............................22-20
FRONT - SPECIFICATIONS, HALF SHAFT . . . 3-15,
3-6
FRONT BRAKE ROTOR - INSTALLATION.....5-54,
5s-57
FRONT BRAKE ROTOR - REMOVAL . . . 5-54,5s-57
FRONT BUMPER REINFORCEMENT -
INSTALLATION........................13-2
FRONT BUMPER REINFORCEMENT -
REMOVAL...........................13-2
FRONT BUSHING - INSTALLATION, LEAF
SPRING.............................2-30
FRONT BUSHING - REMOVAL, LEAF
SPRING.............................2-29
FRONT CABLE - INSTALLATION.....5-64,5s-67
FRONT CABLE - INSTALLATION,
PARKING BRAKE LEVER...........5-66,5s-69
FRONT CABLE - REMOVAL.........5-64,5s-67
FRONT CABLE - REMOVAL, PARKING
BRAKE LEVER...................5-65,5s-68
FRONT CONTROL MODULE -
DESCRIPTION........................8E-7
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING........................8E-7
FRONT CONTROL MODULE -
INSTALLATION........................8E-8
FRONT CONTROL MODULE - OPERATION . . 8E-7
FRONT CONTROL MODULE - REMOVAL....8E-8
FRONT CRADLE CROSSMEMBER -
DESCRIPTION........................13-9
FRONT CRADLE CROSSMEMBER
THREAD REPAIR - DESCRIPTION
.........13-9
FRONT CROSSMEMBER MOUNT
BUSHINGS - INSTALLATION
............13-12
FRONT CROSSMEMBER MOUNT
BUSHINGS - REMOVAL
................13-12
FRONT DISC BRAKE CALIPER ADAPTER
- INSTALLATION
.................5-31,5s-30
FRONT DISC BRAKE CALIPER ADAPTER
- REMOVAL
.....................5-31,5s-30
FRONT DISC BRAKE CALIPER
(CONTINENTAL TEVES BRAKES) -
INSTALLATION
.......................5s-26
FRONT DISC BRAKE CALIPER
(CONTINENTAL TEVES BRAKES) -
REMOVAL
..........................5s-23
FRONT DISC BRAKE CALIPER
(DISC/DISC BRAKES) - INSTALLATION
.....5-27
FRONT DISC BRAKE CALIPER
(DISC/DISC BRAKES) - REMOVAL
.........5-24
FRONT DISC BRAKE CALIPER
(DISC/DRUM BRAKES) -
INSTALLATION
........................5-27
FRONT DISC BRAKE CALIPER
(DISC/DRUM BRAKES) - REMOVAL
.......5-24
FRONT DISC BRAKE CALIPER (TRW
BRAKES) - INSTALLATION
..............5s-26
FRONT DISC BRAKE CALIPER (TRW
BRAKES) - REMOVAL
.................5s-23
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

MODULE - DESCRIPTION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - DESCRIPTION, POWER
LIFTGATE CONTROL..................8E-10
MODULE - DESCRIPTION, REAR
DRIVELINE...........................3-23
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - DESCRIPTION, SENTRY KEY
REMOTE ENTRY......................8Q-3
MODULE - DESCRIPTION, SLIDING
DOOR CONTROL.....................8E-19
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-20
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-7
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8E-9
MODULE - DIAGNOSIS AND TESTING,
MEMORY SEAT/MIRROR...............8E-10
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY.............8N-43
MODULE - DIAGNOSIS AND TESTING,
SENTRY KEY REMOTE ENTRY...........8Q-5
MODULE - EXPORT - DESCRIPTION,
ANTENNA...........................8A-6
MODULE - EXPORT - DIAGNOSIS AND
TESTING, ANTENNA...................8A-7
MODULE - EXPORT - INSTALLATION,
ANTENNA...........................8A-7
MODULE - EXPORT - OPERATION,
ANTENNA.............................8A-6
MODULE - EXPORT - REMOVAL,
ANTENNA...........................8A-7
MODULE - INSTALLATION, BODY
CONTROL............................8s-3
MODULE - INSTALLATION, BODY
CONTROL...........................8E-5
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-8
MODULE - INSTALLATION, FUEL PUMP....14-9
MODULE - INSTALLATION, HEATED SEAT . . 8E-10
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-3
MODULE - INSTALLATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - INSTALLATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY.....................8N-44
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-19
MODULE - INSTALLATION, SENTRY KEY
REMOTE ENTRY......................8Q-6
MODULE - INSTALLATION, SLIDING
DOOR CONTROL.....................8E-20
MODULE - INSTALLATION, WIPER.......8R-15
MODULE - OPERATION, BODY CONTROL . . . 8s-1
MODULE - OPERATION, BODY CONTROL . . . 8E-3
MODULE - OPERATION, FRONT
CONTROL...........................8E-7
MODULE - OPERATION, FUEL PUMP
......14-8
MODULE - OPERATION, HEATED SEAT
.....8E-9
MODULE - OPERATION, INTEGRATED
POWER
..........................8W-97-2
MODULE - OPERATION, MEMORY
SEAT/MIRROR
.......................8E-10
MODULE - OPERATION, POWER
LIFTGATE CONTROL
..................8E-11
MODULE - OPERATION, REAR
DRIVELINE
...........................3-23
MODULE - OPERATION, REMOTE
KEYLESS ENTRY
.....................8N-43
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER
.......................8E-18
MODULE - OPERATION, SENTRY KEY
REMOTE ENTRY
......................8Q-4
MODULE - OPERATION, SLIDING DOOR
CONTROL
..........................8E-19
MODULE - OPERATION, TRANSMISSION
CONTROL
..........................8E-20
MODULE - REAR BLOWER MOTOR -
DESCRIPTION, POWER
................24-41
MODULE - REAR BLOWER MOTOR -
INSTALLATION, POWER
...............24-42MODULE - REAR BLOWER MOTOR -
OPERATION, POWER..................24-41
MODULE - REAR BLOWER MOTOR -
REMOVAL, POWER...................24-41
MODULE - REMOVAL, BODY CONTROL....8s-3
MODULE - REMOVAL, BODY CONTROL....8E-4
MODULE - REMOVAL, FRONT CONTROL . . . 8E-8
MODULE - REMOVAL, FUEL PUMP........14-8
MODULE - REMOVAL, HEATED SEAT......8E-9
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-2
MODULE - REMOVAL, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - REMOVAL, POWER LIFTGATE
CONTROL..........................8E-11
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY.............................8N-44
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - REMOVAL, SENTRY KEY
REMOTE ENTRY......................8Q-5
MODULE - REMOVAL, SLIDING DOOR
CONTROL..........................8E-19
MODULE - REMOVAL, WIPER...........8R-15
MODULE - SPECIFICATIONS, REAR
DRIVELINE...........................3-34
MODULE, BENCH SEAT - REMOVAL,
CHILD SEAT.........................23-87
MODULE FLUIDS - DESCRIPTION, AWD
REAR DRIVELINE......................0-6
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE.................8M-3
MODULE NOISE - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-24
MODULE OPERATION - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-26
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT..................23-115
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT..................23-113
MOLDING - INSTALLATION, ROOF JOINT . . 23-58
MOLDING - REMOVAL, FRONT DOOR
INNER BELT........................23-115
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT.......................23-113
MOLDING - REMOVAL, ROOF JOINT......23-58
MOLDINGS - INSTALLATION, BODY SIDE . . 23-46
MOLDINGS - REMOVAL, BODY SIDE.....23-45
MONITORED COMPONENT -
DESCRIPTION........................25-1
MONITORED SYSTEMS - DESCRIPTION....25-6
MONITORING - DESCRIPTION, TIRE
PRESSURE.....................22-9,22s-1
MONITORING - OPERATION, TIRE
PRESSURE.....................22-9,22s-1
MOTOR - DESCRIPTION, BLOWER . . 24-46,24-57
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-28
MOTOR - DESCRIPTION, LIFTGATE......8N-15
MOTOR - DESCRIPTION, POWER
MODULE - BLOWER..................24-31
MOTOR - DESCRIPTION, POWER
MODULE - REAR BLOWER.............24-41
MOTOR - DESCRIPTION, SLIDING DOOR . . 8N-30
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-47
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
MOTOR - DIAGNOSIS AND TESTING,
RADIATOR FAN.......................7-29
MOTOR - DIAGNOSIS AND TESTING,
REAR BLOWER......................24-58
MOTOR - DIAGNOSIS AND TESTING,
VENT WINDOW......................8N-63
MOTOR - INSTALLATION, BLOWER . 24-49,24-58
MOTOR - INSTALLATION, FRONT
WASHER PUMP......................8R-8
MOTOR - INSTALLATION, FRONT WIPER . . . 8R-9
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-29
MOTOR - INSTALLATION, LIFTGATE
......8N-15
MOTOR - INSTALLATION, POWER
MODULE - BLOWER
..................24-32
MOTOR - INSTALLATION, POWER
MODULE - REAR BLOWER
.............24-42
MOTOR - INSTALLATION, REAR WASHER
PUMP
.............................8R-10
MOTOR - INSTALLATION, REAR WIPER
. . . 8R-11MOTOR - INSTALLATION, SLIDING DOOR . 8N-31
MOTOR - INSTALLATION, SLIDING DOOR
LOCK.........................8N-44,8N-6
MOTOR - INSTALLATION, SUNROOF.....23-121
MOTOR - INSTALLATION, VENT WINDOW . 8N-64
MOTOR - OPERATION, BLOWER....24-46,24-57
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-28
MOTOR - OPERATION, LIFTGATE........8N-15
MOTOR - OPERATION, POWER MODULE
- BLOWER..........................24-31
MOTOR - OPERATION, POWER MODULE
- REAR BLOWER.....................24-41
MOTOR - OPERATION, SLIDING DOOR . . . 8N-30
MOTOR - REMOVAL, BLOWER.....24-47,24-58
MOTOR - REMOVAL, FRONT WASHER
PUMP..............................8R-8
MOTOR - REMOVAL, FRONT WIPER......8R-9
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-29
MOTOR - REMOVAL, LIFTGATE.........8N-15
MOTOR - REMOVAL, POWER MODULE -
BLOWER...........................24-31
MOTOR - REMOVAL, POWER MODULE -
REAR BLOWER......................24-41
MOTOR - REMOVAL, REAR WASHER
PUMP.............................8R-10
MOTOR - REMOVAL, REAR WIPER......8R-11
MOTOR - REMOVAL, SLIDING DOOR.....8N-30
MOTOR - REMOVAL, SLIDING DOOR
LOCK...........................8N-44,8N-6
MOTOR - REMOVAL, SUNROOF........23-121
MOTOR - REMOVAL, VENT WINDOW.....8N-63
MOTOR - REMOVAL, WINDOW..........8N-64
MOTOR RELAY - DESCRIPTION,
BLOWER......................24-24,24-37
MOTOR RELAY - INSTALLATION,
BLOWER......................24-25,24-38
MOTOR RELAY - OPERATION, BLOWER . . 24-24,
24-37
MOTOR RELAY - REMOVAL, BLOWER....24-25,
24-38
MOTOR RESISTOR - DESCRIPTION,
BLOWER...........................24-38
MOTOR RESISTOR - INSTALLATION,
BLOWER...........................24-39
MOTOR RESISTOR - OPERATION,
BLOWER...........................24-38
MOTOR RESISTOR - REMOVAL,
BLOWER...........................24-39
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, REAR BLOWER..........24-38
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER..............24-27
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER...........................24-26
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER...........................24-26
MOUNT - INSTALLATION, FRONT....9-131,9-49
MOUNT - INSTALLATION, LEFT......9-133,9-50
MOUNT - INSTALLATION, REAR.....9-134,9-50
MOUNT - INSTALLATION, RIGHT....9-135,9-51
MOUNT - REMOVAL, FRONT........9-131,9-49
MOUNT - REMOVAL, LEFT.........9-133,9-49
MOUNT - REMOVAL, REAR.........9-133,9-50
MOUNT - REMOVAL, RIGHT........9-135,9-51
MOUNT BUSHINGS - INSTALLATION,
FRONT CROSSMEMBER...............13-12
MOUNT BUSHINGS - REMOVAL, FRONT
CROSSMEMBER.....................13-12
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH...........8L-6
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH
...............8L-6
MOUNTING - DESCRIPTION, ENGINE
. 9-131,9-48
MOUNTING - STANDARD PROCEDURE,
TIRE AND WHEEL MATCH
...............22-7
MOUNTING BRACKET - 2.4L ENGINE -
INSTALLATION, A/C COMPRESSOR
.......24-76
MOUNTING BRACKET - 2.4L ENGINE -
REMOVAL, A/C COMPRESSOR
..........24-75
22 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

MOUNTING STUDS - FRONT -
INSTALLATION, WHEEL................22-21
MOUNTING STUDS - FRONT - REMOVAL,
WHEEL............................22-20
MOUNTING STUDS - REAR -
INSTALLATION, WHEEL................22-22
MOUNTING STUDS - REAR - REMOVAL,
WHEEL............................22-21
MOUNTS - FRONT - INSTALLATION,
SPRING.............................2-44
MOUNTS - FRONT - REMOVAL, SPRING . . . 2-43
MOUNTS - REAR - INSTALLATION,
SPRING.............................2-45
MOUNTS - REAR - REMOVAL, SPRING....2-44
MUFFLER - INSTALLATION..............11-7
MUFFLER - REMOVAL..................11-7
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-18
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-18
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - ADHESIVE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - ADHESIVE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NAME PLATES - TAPE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - TAPE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-13
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-13
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP TO FILLER..............7-27
NGC CONTROLLER - REMOVAL.........8E-17
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-47
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-47
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-47
NO CUPHOLDER - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NO CUPHOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NOISE - DIAGNOSIS AND TESTING,
EXCESSIVE EXHAUST SYSTEM...........11-2
NOISE - DIAGNOSIS AND TESTING,
REAR DRIVELINE MODULE..............3-24
NOISE - DIAGNOSIS AND TESTING, TIRE . 22-14,
22s-6
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-74
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, HYDRAULIC LASH
ADJUSTER...........................9-34
NOISE SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO.................8A-11
NOISE SUPPRESSION COMPONENTS -
OPERATION, RADIO..................8A-12
NON-ABS JUNCTION BLOCK -
DESCRIPTION...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
INSTALLATION
...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
OPERATION
.....................5-33,5s-32
NON-ABS JUNCTION BLOCK - REMOVAL
. . 5-33,
5s-32
NON-MONITORED CIRCUITS -
OPERATION
..........................25-5
NOT FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES
......................25-16
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION
....................Intro.-9
NVLD - INSTALLATION, WITH
...........25-20
NVLD - REMOVAL, WITH
..............25-19
O2 SENSOR - DESCRIPTION
............14-32
O2 SENSOR - OPERATION
.............14-32
OBTAINING DIAGNOSTIC TROUBLE
CODES - STANDARD PROCEDURE
.......8E-15
OCCUPANT RESTRAINT CONTROLLER -
DESCRIPTION
........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
INSTALLATION
.......................8O-8OCCUPANT RESTRAINT CONTROLLER -
OPERATION..........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
REMOVAL...........................8O-8
OIL - DESCRIPTION, FLEXIBLE FUEL
ENGINE..............................0-3
OIL - DESCRIPTION, REFRIGERANT......24-92
OIL - DIESEL ENGINES - DESCRIPTION,
ENGINE..............................0-6
OIL - OPERATION, REFRIGERANT........24-92
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE.............9-137,9-53
OIL AND LUBRICANTS - DESCRIPTION,
ENGINE..............................0-1
OIL COOLER - DESCRIPTION,
TRANSMISSION.......................7-37
OIL COOLER - INSPECTION,
TRANSMISSION.......................7-37
OIL COOLER - INSTALLATION,
TRANSMISSION.......................7-37
OIL COOLER & LINES - DESCRIPTION....9-138
OIL COOLER & LINES - INSTALLATION . . . 9-138
OIL COOLER & LINES - OPERATION......9-138
OIL COOLER & LINES - REMOVAL.......9-138
OIL COOLER - REMOVAL,
TRANSMISSION.......................7-37
OIL COOLER LINES - INSTALLATION,
TRANSMISSION.......................7-38
OIL COOLER LINES - REMOVAL,
TRANSMISSION.......................7-38
OIL FILTER - DESCRIPTION.............9-53
OIL FILTER - INSTALLATION........9-139,9-53
OIL FILTER - REMOVAL............9-139,9-53
OIL FILTER ADAPTER - INSTALLATION....9-139
OIL FILTER ADAPTER - REMOVAL.......9-139
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE.........9-10,9-86
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..............9-8,9-82
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-93
OIL LEVEL CHECK - STANDARD
PROCEDURE, ENGINE.................9-137
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-53
OIL PAN - CLEANING.................9-140
OIL PAN - INSPECTION................9-140
OIL PAN - INSTALLATION..........9-140,9-54
OIL PAN - REMOVAL..............9-140,9-54
OIL PRESSURE - DIAGNOSIS AND
TESTING, CHECKING ENGINE............9-52
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE....................9-136
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-141
OIL PRESSURE RELIEF VALVE -
REMOVAL..........................9-141
OIL PRESSURE SWITCH - DESCRIPTION . . 9-141
OIL PRESSURE SWITCH - INSTALLATION . 9-141,
9-54
OIL PRESSURE SWITCH - OPERATION....9-141
OIL PRESSURE SWITCH - REMOVAL . 9-141,9-54
OIL PUMP - ASSEMBLY...........9-143,9-56
OIL PUMP - ASSEMBLY.......21-232,21s-132
OIL PUMP - CLEANING............9-142,9-56
OIL PUMP - DESCRIPTION.............9-142
OIL PUMP - DESCRIPTION.....21-230,21s-131
OIL PUMP - DISASSEMBLY........9-142,9-55
OIL PUMP - DISASSEMBLY.....21-230,21s-131
OIL PUMP - INSPECTION..........9-142,9-56
OIL PUMP - INSTALLATION........9-144,9-57
OIL PUMP - INSTALLATION, SEAL......21-233,
21s-133
OIL PUMP - OPERATION.......21-230,21s-131
OIL PUMP - REMOVAL............9-142,9-55
OIL PUMP - REMOVAL, SEAL . . . 21-232,21s-133
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT...................9-127,9-40
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT
...................9-127,9-40
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
...................9-129,9-42
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT
...................9-128,9-41
OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR
..................9-129
OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR
..................9-129OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-28
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-27
ON-BOARD DIAGNOSTIC SYSTEM -
DIAGNOSIS AND TESTING..............8F-21
OPEN LATCH - INSTALLATION, HOLD.....23-25
OPEN LATCH - REMOVAL, HOLD........23-25
OPEN LATCH CABLE - INSTALLATION,
HOLD..............................23-38
OPEN LATCH CABLE - REMOVAL, HOLD . . . 23-38
OPEN LATCH STRIKER - INSTALLATION,
HOLD..............................23-26
OPEN LATCH STRIKER - REMOVAL,
HOLD..............................23-26
OPEN SWITCH - DESCRIPTION, FULL....8N-12,
8N-31
OPEN SWITCH - INSTALLATION, FULL....8N-13
OPEN SWITCH - OPERATION, FULL . 8N-12,8N-31
OPEN SWITCH - REMOVAL, FULL.......8N-13
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-13
OPENING DIMENSIONS -
SPECIFICATIONS, BODY..............23-127
OPENING REINFORCEMENT -
INSTALLATION, GRILLE................23-54
OPENING REINFORCEMENT - REMOVAL,
GRILLE............................23-54
ORDER, SPECIFICATIONS - FIRING........8I-3
O-RING - INSTALLATION, REAR COVER . . . 21-20
O-RING - REMOVAL, REAR COVER.......21-19
ORVR - OPERATION..................25-14
OUTBOARD - FRONT - INSTALLATION,
SEAT BELT & RETRACTOR.............8O-14
OUTBOARD - FRONT - REMOVAL, SEAT
BELT & RETRACTOR..................8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - FIRST ROW...........8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW - LEFT . . . 8O-17
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW -
RIGHT.............................8O-15
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - FIRST ROW.............8O-14
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - LEFT.....8O-17
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-15
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-16
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT & RETRACTOR -
SECOND ROW - RIGHT................8O-16
OUTER - INSTALLATION, CV BOOT........3-10
OUTER - REMOVAL, CV BOOT...........3-10
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-113
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-113
OUTER HALF SHAFT SEAL -
INSTALLATION.......................21-19
OUTER HALF SHAFT SEAL - REMOVAL . . . 21-19
OUTER TIE ROD - INSTALLATION........19-34
OUTER TIE ROD - REMOVAL...........19-34
OUTLET - DESCRIPTION, POWER......8W-97-4
OUTLET - DIAGNOSIS & TESTING,
POWER..........................8W-97-4
OUTLET - INSTALLATION, DEMISTER
.....24-46
OUTLET - INSTALLATION, INSTRUMENT
PANEL
.............................24-46
OUTLET - OPERATION, POWER
.......8W-97-4
OUTLET - REMOVAL, DEMISTER
........24-45
OUTLET - REMOVAL, INSTRUMENT
PANEL
.............................24-45
OUTLETS - DESCRIPTION, AIR
.....24-44,24-56
OUTLETS - INSTALLATION, AIR
.........24-56
OUTLETS - INSTALLATION, CENTER
BEZEL
.............................24-45
OUTLETS - REMOVAL, AIR
.............24-56
OUTLETS - REMOVAL, CENTER BEZEL
....24-44
OUTPUT - DESCRIPTION, SPEED
SENSOR
....................21-241,21s-142
OUTPUT - INSTALLATION, SPEED
SENSOR
....................21-242,21s-143
OUTPUT - OPERATION, 5 VOLT SUPPLY -
PCM
...............................8E-15
RSINDEX23
Description Group-Page Description Group-Page Description Group-Page