2004 CHRYSLER VOYAGER tire pressure

CHARGING PROCEDURE
CAUTION: A small amount of refrigerant oil is
removed from the A/C system each time the refrig-
erant system is recovered and evacuated. Before
charging the A/C system, you MUST replenish any
oil lost during the recovery process. Refer the
equipment manufacturer instructions for more infor-
mation.
(1) Evacuate the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
FRONT/REFRIGERANT - STANDARD PROCE-
DURE - REFRIGERANT SYSTEM EVACUATE).
(2) A manifold gauge set and a R-134a refrigerant
recovery/recycling/charging station that meets SAE
Standard J2210 should still be connected to the
refrigerant system.
(3) Measure the proper amount of refrigerant and
heat it to 52É C (125É F) with the charging station.
See the operating instructions supplied by the equip-
ment manufacturer for proper use of this equipment.
(4) Open both the suction and discharge valves,
then open the charge valve to allow the heated
refrigerant to flow into the system.
(5) When the transfer of refrigerant has stopped,
close both the suction and discharge valves.
(6) If all of the refrigerant charge did not transfer
from the dispensing device, open all of the windows
in the vehicle and set the heater-air conditioner con-
trols so that the compressor is engaged and the
blower motor is operating at its lowest speed setting.
Run the engine at a steady high idle (about 1400
rpm). If the compressor will not engage, test the com-
pressor clutch control circuit and repair as required.
(7) Open the suction valve to allow the remaining
refrigerant to transfer to the refrigerant system.
WARNING: TAKE CARE NOT TO OPEN THE DIS-
CHARGE (HIGH PRESSURE) VALVE AT THIS TIME.
(8) Close the suction valve and test the system
performance. (Refer to 24 - HEATING & AIR CON-
DITIONING - STANDARD PROCEDURE - A/C PER-
FORMANCE TEST).
(9) Disconnect the charging station and manifold
gauge set from the refrigerant system service ports.
(10) Reinstall the caps onto the refrigerant system
service ports.
(11) Run the HVAC Control Cooldown test to ver-
ify proper operation(Refer to 24 - HEATING & AIR
CONDITIONING - DIAGNOSIS AND TESTING).A/C COMPRESSOR
DESCRIPTION
DESCRIPTION - A/C COMPRESSOR
Vehicles equipped with the 2.5L diesel, 3.3L and
3.8L gasoline engines use the Denso 10S20 A/C com-
pressor. Vehicles equipped with the 2.4L gasoline
engine use the Denso 10S17 A/C compressor. Both
A/C compressors include an integral high pressure
relief valve. The A/C compressor is secured to a
mounting bracket on the 2.4L gasoline engine and
directly to the cylinder block on the 2.5L diesel, 3.3L
and 3.8L gasoline engines.
DESCRIPTION - HIGH PRESSURE RELIEF
VALVE
A high pressure relief valve is located on the rear
of the A/C compressor. This mechanical valve is
designed to vent refrigerant from the A/C system to
protect against damage to the compressor and other
system components, caused by condenser air flow
restriction or an overcharge of refrigerant.
OPERATION
OPERATION - A/C COMPRESSOR
The A/C compressor is driven by the engine
through an electric clutch, drive pulley and belt
arrangement. The compressor is lubricated by refrig-
erant oil that is circulated throughout the refrigerant
system with the refrigerant.
The compressor draws in low-pressure refrigerant
vapor from the evaporator through its suction port. It
then compresses the refrigerant into a high-pressure,
high-temperature refrigerant vapor. The compressor
pumps the high-pressure refrigerant vapor to the
condenser through the compressor discharge port.
The compressor cannot be repaired. If faulty or
damaged, the entire compressor assembly must be
replaced. The compressor clutch, pulley and clutch
coil are available for service.
OPERATION - HIGH PRESSURE RELIEF VALVE
The high pressure relief valve vents the system
when a discharge pressure of 3445 to 4135 kPa (500
to 600 psi) or above is reached. The valve closes
when a minimum discharge pressure of 2756 kPa
(400 psi) is reached.
The high pressure relief valve vents only enough
refrigerant to reduce the system pressure, and then
re-seats itself. The majority of the refrigerant is con-
served in the system. If the valve vents refrigerant, it
does not mean that the valve is faulty.
RSPLUMBING - FRONT24-73
PLUMBING - FRONT (Continued)

(18) Install plugs in, or tape over the opened suc-
tion line fittings.
(19) Lower the vehicle.
(20) Remove the suction line from the engine com-
partment.
INSTALLATION
(1) Position the suction line into the engine com-
partment.
(2) Remove the tape or plugs from the suction line
and liquid line fittings and both expansion valve
ports.
(3) Lubricate new rubber O-ring seals with clean
refrigerant oil and install them on the suction line
and liquid line fittings.
(4) Reconnect the liquid line and suction line fit-
tings to the expansion valve.
(5) Install the nut that secures the suction line
and liquid line fittings to the front expansion valve.
Tighten the nut to 23 N´m (17 ft. lbs.).
(6) Engage the retainer that secures the suction
line routing clip to the receiver/drier mounting
bracket on the side of the right front strut tower in
the engine compartment.
(7) Remove the tape or plugs from the compressor
suction port and the suction line fitting.
(8) Lubricate a new rubber O-ring seal with clean
refrigerant oil and install it on the suction line fit-
ting.
(9) Reconnect the suction line fitting to the com-
pressor suction port.
(10) Install the nut that secures the suction line
fitting to the A/C compressor. Tighten the nut to 23
N´m (17 ft. lbs.).
(11) Reconnect the drain tube to the wiper module
drain on the right side of the engine compartment.
(12) Reinstall the air cleaner top cover and snorkel
onto the air cleaner housing located on the right side
of the engine compartment.
(13) Reconnect the battery negative cable.
(14) Raise and support the vehicle.
(15) Remove the tape or plugs from the suction
line extension fitting and the underbody suction line
fitting.(16) Lubricate a new rubber O-ring seal with clean
refrigerant oil and install it on the underbody suction
line fitting.
(17) Reconnect the suction line extension fitting to
the underbody suction line fitting. Tighten the fitting
to 23 N´m (17 ft. lbs.).
(18) Install a new tie strap just forward of the con-
nections between the underbody plumbing and the
engine compartment plumbing for the rear heater
and air conditioner.
(19) Lower the vehicle.
(20) Evacuate the refrigerant system (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
FRONT/REFRIGERANT - STANDARD PROCE-
DURE - REFRIGERANT SYSTEM EVACUATE).
(21) Charge the refrigerant system (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
FRONT/REFRIGERANT - STANDARD PROCE-
DURE - REFRIGERANT SYSTEM CHARGE).
UNDERBODY LINES
DESCRIPTION
The underbody heater-A/C plumbing is used only
on models with the optional rear heater-A/C system
(Fig. 11). The underbody suction line, liquid line, and
heater tubes can each be serviced separately.
OPERATION
The rear heater and A/C lines are all serviced as
individual pieces. When disconnecting any line or
block ensure that the area around it is clean of any
contaminations that can get in to the system (Fig.
12), (Fig. 13), (Fig. 15), (Fig. 14) and (Fig. 16).
Any kinks or sharp bends in the rear heater-A/C
unit plumbing will reduce the capacity of the entire
heating and air conditioning system. Kinks and
sharp bends reduce the system flow. High pressures
are produced in the refrigerant system when the air
conditioning compressor is operating. High tempera-
ture coolant is present in the heater plumbing when
the engine is operating. Extreme care must be exer-
cised o make sure that each of the plumbing connec-
tions is pressure-tight and leak free.
RSPLUMBING - REAR24 - 107
SUCTION LINE (Continued)

HEATED SEAT SWITCH - INSTALLATION,
DRIVER............................8G-10
HEATED SEAT SWITCH - INSTALLATION,
PASSENGER........................8G-14
HEATED SEAT SWITCH - OPERATION,
DRIVER.............................8G-8
HEATED SEAT SWITCH - OPERATION,
PASSENGER........................8G-12
HEATED SEAT SWITCH - REMOVAL,
DRIVER............................8G-10
HEATED SEAT SWITCH - REMOVAL,
PASSENGER........................8G-14
HEATED SEAT SYSTEM - DESCRIPTION....8G-7
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SYSTEM - OPERATION.....8G-8
HEATER - DESCRIPTION, CABIN........24-112
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-20
HEATER - DIAGNOSIS AND TESTING,
DIESEL SUPPLEMENTAL CABIN........24-113
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-20
HEATER - OPERATION, ENGINE BLOCK....7-20
HEATER - REMOVAL, ENGINE BLOCK......7-20
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-4
HEATER CONTROL - DESCRIPTION, A/C . . . 24-20
HEATER CONTROL - INSTALLATION, A/C . . 24-21
HEATER CONTROL - REMOVAL, A/C.......24-21
HEATER CORE - DESCRIPTION....24-101,24-83
HEATER CORE - INSTALLATION . . . 24-103,24-85
HEATER CORE - OPERATION......24-101,24-83
HEATER CORE - REMOVAL.......24-102,24-84
HEATER CORE FILLING - STANDARD
PROCEDURE, REAR..................24-101
HEATER CORE TUBES - INSTALLATION . . . 24-85
HEATER CORE TUBES - REMOVAL.......24-83
HEATER HOSES - INSTALLATION.......24-104
HEATER HOSES - REMOVAL...........24-103
HEATER INLET HOSE - INSTALLATION....24-86
HEATER INLET HOSE - REMOVAL........24-85
HEATER LINES - INSTALLATION, REAR . . 24-111
HEATER PERFORMANCE TEST -
DIAGNOSIS AND TESTING.............24-10
HEATER RETURN HOSE - INSTALLATION . . 24-87
HEATER RETURN HOSE - REMOVAL......24-86
HEATER TESTING - DIAGNOSIS AND
TESTING, ENGINE BLOCK...............7-20
HEATER TUBES - REMOVAL,
UNDERBODY.......................24-109
HEATER UNIT - INSTALLATION.........24-119
HEATER UNIT - REMOVAL.............24-118
HEATER WIRING - INSTALLATION,
SUPPLEMENTAL DIESEL..............24-119
HEATER WIRING - REMOVAL,
SUPPLEMENTAL DIESEL..............24-119
HEAVY DUTY, CARGO - INSTALLATION,
AWD ...............................2-36
HEAVY DUTY, CARGO - REMOVAL, AWD . . . 2-36
HEIGHT ADJUSTER-BORC-PILLAR -
INSTALLATION, SEAT BELT.............8O-13
HEIGHT ADJUSTER-BORC-PILLAR -
REMOVAL, SEAT BELT................8O-13
HEIGHT ADJUSTER KNOB -
INSTALLATION, SEAT BELT.............8O-14
HEIGHT ADJUSTER KNOB - REMOVAL,
SEAT BELT .........................8O-14
HEIGHT MEASUREMENT - STANDARD
PROCEDURE, CURB...................2-55
HIGH AND LOW LIMITS - DESCRIPTION . . . 25-8
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION
.......................24-73
HIGH PRESSURE RELIEF VALVE -
OPERATION
.........................24-73
HIGH SPEED OPERATION - STANDARD
PROCEDURE, TIRE PRESSURE
.....22-17,22s-9
HINGE - INSTALLATION
......23-18,23-40,23-60
HINGE - INSTALLATION, CENTER
........23-24HINGE - INSTALLATION, LOWER........23-28
HINGE - INSTALLATION, UPPER.........23-36
HINGE - REMOVAL.........23-17,23-40,23-60
HINGE - REMOVAL, BENCH SEAT BACK . . 23-102
HINGE - REMOVAL, CENTER............23-24
HINGE - REMOVAL, LOWER............23-28
HINGE - REMOVAL, UPPER.............23-36
HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - INSTALLATION, SEAT
BACK.............................23-101
HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - REMOVAL, SEAT BACK . . 23-101
HOISTING - STANDARD PROCEDURE......0-27
HOLD OPEN LATCH - INSTALLATION.....23-25
HOLD OPEN LATCH - REMOVAL.........23-25
HOLD OPEN LATCH CABLE -
INSTALLATION.......................23-38
HOLD OPEN LATCH CABLE - REMOVAL . . . 23-38
HOLD OPEN LATCH STRIKER -
INSTALLATION.......................23-26
HOLD OPEN LATCH STRIKER -
REMOVAL..........................23-26
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-15
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-16
HOLDDOWN - OPERATION, BATTERY.....8F-15
HOLDDOWN - REMOVAL, BATTERY . 8F-15,8F-16
HOLDER - INSTALLATION, CUP.........23-64
HOLDER - REMOVAL, CUP.............23-64
HOLDING CLUTCHES - DESCRIPTION . . . 21-207,
21s-106
HOLDING CLUTCHES - OPERATION.....21-207,
21s-106
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-5
HONING - STANDARD PROCEDURE,
CYLINDER BORE.................9-112,9-35
HOOD - INSTALLATION................23-61
HOOD - REMOVAL....................23-60
HOOD AJAR SWITCH - EXPORT -
INSTALLATION.......................8Q-3
HOOD AJAR SWITCH - EXPORT -
REMOVAL...........................8Q-3
HORN - DIAGNOSIS AND TESTING.......8H-3
HORN - INSTALLATION.................8H-5
HORN - REMOVAL....................8H-4
HORN CHIRP PREFERENCE - STANDARD
PROCEDURE....................8N-42,8N-5
HORN SWITCH - DESCRIPTION..........8H-5
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - INSTALLATION, HEATER INLET....24-86
HOSE - INSTALLATION, HEATER RETURN . 24-87
HOSE - REMOVAL, HEATER INLET.......24-85
HOSE - REMOVAL, HEATER RETURN.....24-86
HOSE CLAMPS - DESCRIPTION...........7-1
HOSE CLAMPS - OPERATION.............7-2
HOSES - DESCRIPTION, BRAKE TUBES....5-14,
5s-13
HOSES - INSPECTION, BRAKE TUBES.....5-14,
5s-13
HOSES - INSTALLATION, HEATER.......24-104
HOSES - INSTALLATION, WASHER.......8R-13
HOSES - OPERATION, BRAKE TUBES . 5-14,5s-13
HOSES - REMOVAL, HEATER..........24-103
HOSES - REMOVAL, WASHER..........8R-13
HOSES AND CLAMP - STANDARD
PROCEDURE.........................14-7
HOUSING - INSTALLATION, AIR
CLEANER........................9-24,9-99
HOUSING - INSTALLATION, HVAC........24-61
HOUSING - INSTALLATION, LOCK
CYLINDER..........................19-19
HOUSING - REMOVAL, AIR CLEANER . . 9-24,9-99
HOUSING - REMOVAL, HVAC...........24-60
HOUSING - REMOVAL, LOCK CYLINDER . . 19-17
HOUSING FLUID CHANGE - STANDARD
PROCEDURE, OVERRUNNING CLUTCH.....3-41
HOUSING FLUID LEAKAGE - DIAGNOSIS
AND TESTING, TORQUE CONVERTER . . . 21-123,
21s-31
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION
.....................8W-01-1
HUB / BEARING - DESCRIPTION
.......2-30,2-4
HUB / BEARING - INSTALLATION
......2-33,2-6
HUB / BEARING - OPERATION
........2-30,2-4
HUB / BEARING - REMOVAL
..........2-31,2-5HUB AND BEARING - DIAGNOSIS AND
TESTING.........................2-31,2-5
HVAC - LWB - INSTALLATION, SEAT
BELT & RETRACTOR - SECOND ROW -
RIGHT OUTBOARD WITH REAR.........8O-16
HVAC - LWB - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR...............8O-16
HVAC HOUSING - INSTALLATION........24-61
HVAC HOUSING - REMOVAL............24-60
HVAC LOUVER - INSTALLATION, REAR . . . 23-81
HVAC LOUVER - REMOVAL, REAR.......23-81
HYDRAULIC CIRCUITS AND VALVES -
OPERATION..........................5-83
HYDRAULIC LASH ADJUSTER NOISE
DIAGNOSIS - DIAGNOSIS AND
TESTING............................9-34
HYDRAULIC LASH ADJUSTERS -
INSTALLATION........................9-34
HYDRAULIC LASH ADJUSTERS -
REMOVAL...........................9-34
HYDRAULIC LIFTERS - DIAGNOSIS AND
TESTING...........................9-113
HYDRAULIC LIFTERS (CAM IN BLOCK) -
DESCRIPTION.......................9-113
HYDRAULIC LIFTERS (CAM IN BLOCK) -
INSTALLATION.......................9-114
HYDRAULIC LIFTERS (CAM IN BLOCK) -
REMOVAL..........................9-114
HYDRAULIC PRESSURE TESTS -
DIAGNOSIS AND TESTING.......21-120,21s-28
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS - 41TE TRANSAXLE....21-169
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS - 4XTE TRANSAXLE....21s-75
HYDROSTATIC LOCKED ENGINE -
STANDARD PROCEDURE............9-10,9-85
ICU - ASSEMBLY......................5-94
ICU - DISASSEMBLY...................5-93
ICU (INTEGRATED CONTROL UNIT) -
DESCRIPTION........................5-89
ICU (INTEGRATED CONTROL UNIT) -
OPERATION..........................5-90
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-2
IDENTIFICATION - DESCRIPTION,
VEHICLE............................23-1
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION, DIAGNOSIS AND
TESTING - SEAL......................21-3
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-9
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-28
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-29
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-28
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-29
IGNITION COIL - DESCRIPTION...........8I-6
IGNITION COIL - OPERATION.............8I-7
IGNITION INTERLOCK - DESCRIPTION....19-17
IGNITION SENSE - PCM INPUT -
OPERATION.........................8E-15
IGNITION SWITCH - INSTALLATION......19-16
IGNITION SWITCH - REMOVAL..........19-14
IGNITION SYSTEM - DESCRIPTION........8I-1
IGNITION SYSTEM - OPERATION..........8I-1
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-13
IIITSTATE DISPLAY TEST MODE,
OPERATION - DRB....................25-9
ILLUMINATION LAMPS - INSTALLATION,
CLUSTER...........................8L-21
ILLUMINATION LAMPS - REMOVAL,
CLUSTER...........................8L-21
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY
........................8E-18
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY
........................8E-19
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY
........................8E-18
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY
........................8E-18
INBOARD - 50/50 BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW
.......................8O-13
RSINDEX17
Description Group-Page Description Group-Page Description Group-Page

INBOARD - 50/50 BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-13
INBOARD - INSTALLATION, SEAT BELT
BUCKLE - FRONT....................8O-12
INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE -
FIRST ROW.........................8O-12
INBOARD - QUAD BUCKET - REMOVAL,
SEAT BELT BUCKLE - FIRST ROW.......8O-12
INBOARD - REMOVAL, SEAT BELT
BUCKLE - FRONT....................8O-12
INDICATOR LAMP - DESCRIPTION,
VTSS/SKIS..........................8Q-7
INDICATOR LAMP - OPERATION,
VTSS/SKIS..........................8Q-8
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR..........22-16,22s-8
INFLATION PRESSURES - STANDARD
PROCEDURE, TIRE..............22-16,22s-8
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-6
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INFRARED TEMPERATURE SENSOR -
DESCRIPTION.......................24-29
INFRARED TEMPERATURE SENSOR -
OPERATION.........................24-29
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-37
INJECTION SYSTEM - OPERATION.......14-18
INJECTOR - DESCRIPTION, FUEL........14-26
INJECTOR - OPERATION, FUEL..........14-26
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-30
INLET FILTER - INSTALLATION..........14-13
INLET FILTER - REMOVAL..............14-13
INLET HOSE - INSTALLATION, HEATER....24-86
INLET HOSE - REMOVAL, HEATER.......24-85
INLET TUBE - 2.4L - DESCRIPTION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - INSTALLATION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - REMOVAL, WATER
PUMP..............................7-35
INLET TUBE - 3.3/3.8L - INSTALLATION,
WATER PUMP........................7-36
INLET TUBE - 3.3/3.8L - REMOVAL,
WATER PUMP........................7-36
INNER - INSTALLATION, CV BOOT.........3-6
INNER - REMOVAL, CV BOOT.............3-6
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-115
INNER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-115
INNER SEAL - INSTALLATION, HALF
SHAFT.............................21-12
INNER SEAL - REMOVAL, HALF SHAFT . . . 21-12
INNER/OUTER - INSTALLATION, CV
BOOT...............................3-17
INNER/OUTER - REMOVAL, CV BOOT......3-15
INPUT - DESCRIPTION, SPEED SENSOR . 21-239,
21s-140
INPUT - INSTALLATION, SPEED
SENSOR....................21-240,21s-141
INPUT - OPERATION, DATA BUS
COMMUNICATION RECEIVE - PCM.......8E-15
INPUT - OPERATION, IGNITION SENSE -
PCM...............................8E-15
INPUT - OPERATION, SENSOR RETURN -
PCM...............................8E-15
INPUT - OPERATION, SPEED SENSOR . . . 21-240,
21s-140
INPUT - REMOVAL, SPEED SENSOR....21-240,
21s-141
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-216,
21s-116
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY...............21-208,21s-107
INPUT FLANGE SEAL - INSTALLATION
.....3-45
INPUT FLANGE SEAL - REMOVAL
.........3-44
INPUT SHAFT - ASSEMBLY
........21-96,21s-5
INPUT SHAFT - DESCRIPTION
.....21-93,21s-1
INPUT SHAFT - DISASSEMBLY
.....21-93,21s-1INPUT SHAFT COVER SEAL -
INSTALLATION.......................21-14
INPUT SHAFT COVER SEAL - REMOVAL . . . 21-13
INPUT SHAFT END SEAL -
INSTALLATION.......................21-16
INPUT SHAFT END SEAL - REMOVAL.....21-15
INPUT SHAFT SEAL - INSTALLATION.....21-18
INPUT SHAFT SEAL - REMOVAL.........21-17
INSIDE HANDLE ACTUATOR -
INSTALLATION.......................23-27
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-27
INSIDE HANDLE CABLE - INSTALLATION . . 23-38
INSIDE HANDLE CABLE - REMOVAL......23-37
INSIDE LATCH HANDLE - INSTALLATION . . 23-34
INSIDE LATCH HANDLE - REMOVAL......23-34
INSPECT, INSPECTION...............21-114
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-1
INSTRUMENT CLUSTER - OPERATION.....8J-1
INSTRUMENT PANEL - INSTALLATION,
LOWER............................23-69
INSTRUMENT PANEL - REMOVAL,
LOWER............................23-69
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-9
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-8
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-66
INSTRUMENT PANEL ASSEMBLY -
REMOVAL............................23-65
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-68
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-68
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-55
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-55
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-55
INSTRUMENT PANEL DUCTS - REMOVAL . 24-55
INSTRUMENT PANEL END CAP -
INSTALLATION.......................23-68
INSTRUMENT PANEL END CAP -
REMOVAL..........................23-68
INSTRUMENT PANEL OUTLET -
INSTALLATION.......................24-46
INSTRUMENT PANEL OUTLET -
REMOVAL..........................24-45
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-69
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-68
INSTRUMENT PANEL TOP PAD
ASSEMBLY - INSTALLATION............23-72
INSTRUMENT PANEL TOP PAD
ASSEMBLY - REMOVAL................23-71
INTAKE MANIFOLD - DESCRIPTION . . 9-144,9-58
INTAKE MANIFOLD - INSTALLATION,
LOWER............................9-149
INTAKE MANIFOLD - INSTALLATION,
UPPER.............................9-147
INTAKE MANIFOLD - LOWER -
CLEANING..........................9-148
INTAKE MANIFOLD - LOWER -
INSPECTION....................9-148,9-60
INTAKE MANIFOLD - LOWER -
INSTALLATION........................9-60
INTAKE MANIFOLD - LOWER - REMOVAL . . 9-60
INTAKE MANIFOLD - REMOVAL, LOWER . . 9-148
INTAKE MANIFOLD - REMOVAL, UPPER . . . 9-145
INTAKE MANIFOLD - UPPER -
INSPECTION.........................9-59
INTAKE MANIFOLD - UPPER -
INSTALLATION........................9-59
INTAKE MANIFOLD - UPPER - REMOVAL . . . 9-58
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING...................9-145,9-58
INTAKE MANIFOLD VACUUM PORT
REPAIR - STANDARD PROCEDURE.......9-145
INTAKE PIPE - INSTALLATION, AIR
......24-114
INTAKE PIPE - REMOVAL, AIR
.........24-113
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.................9-105,9-32,9s-22
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
..............9-104,9-32,9s-21
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...................9-105,9s-22INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..................9-106,9s-23
INTAKE/EXHAUST VALVES & SEATS -
OPERATION....................9-104,9s-21
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.....................9-105,9s-22
INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER GLASS.........8A-9
INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER
GLASS..............................8A-9
INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER GLASS...........8A-9
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-2
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-3
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-2
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-2
INTERACTIVE SPEED CONTROL (4
SPEED EATX ONLY) - OPERATION........8P-2
INTERFACE (PCI) BUS, OPERATION -
PROGRAMMABLE COMMUNICATIONS....14-21
INTERIOR LAMPS, SPECIFICATIONS......8L-20
INTERLOCK - DESCRIPTION, IGNITION....19-17
INTERLOCK SOLENOID - DESCRIPTION,
SHIFT......................21-233,21s-133
INTERLOCK SOLENOID - DIAGNOSIS
AND TESTING, BRAKE/TRANSMISSION
SHIFT......................21-235,21s-135
INTERLOCK SOLENOID - INSTALLATION,
SHIFT.......................21-236,21s-136
INTERLOCK SOLENOID - OPERATION,
SHIFT......................21-233,21s-134
INTERLOCK SOLENOID - REMOVAL,
SHIFT......................21-235,21s-135
INTERLOCK SWITCH - INSTALLATION,
CLUTCH PEDAL.......................6-14
INTERLOCK SWITCH - REMOVAL,
CLUTCH PEDAL.......................6-13
INTERMEDIATE SHAFT - ASSEMBLY....21-107,
21s-17
INTERMEDIATE SHAFT - DESCRIPTION . . 21-100,
21s-9
INTERMEDIATE SHAFT - DISASSEMBLY . 21-100,
21s-10
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-5
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-3,9-76
IOD FUSE - DESCRIPTION...........8W-97-3
IOD FUSE - OPERATION.............8W-97-3
JOINT - DESCRIPTION, LOWER BALL......2-10
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - OPERATION, LOWER BALL.......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-58
JOINT MOLDING - REMOVAL, ROOF......23-58
JOUNCE BUMPER - DESCRIPTION........2-36
JOUNCE BUMPER - OPERATION..........2-36
JUMP STARTING - STANDARD
PROCEDURE.........................0-27
JUNCTION BLOCK - DESCRIPTION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - INSTALLATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - OPERATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - REMOVAL, NON-ABS . . 5-33,
5s-32
KEY - DESCRIPTION, TRANSPONDER.....8Q-6
KEY - OPERATION, TRANSPONDER.......8Q-6
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY................8E-18
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-19
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY
.................8E-18
KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY
............................8E-18
KEY REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY
................8Q-3
KEY REMOTE ENTRY MODULE -
DIAGNOSIS AND TESTING, SENTRY
.......8Q-5
18 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

KEY REMOTE ENTRY MODULE -
INSTALLATION, SENTRY................8Q-6
KEY REMOTE ENTRY MODULE -
OPERATION, SENTRY..................8Q-4
KEY REMOTE ENTRY MODULE -
REMOVAL, SENTRY...................8Q-5
KEY REMOTE ENTRY SYSTEM -
DIAGNOSIS AND TESTING, SENTRY.......8Q-3
KEYLESS ENTRY MODULE -
DESCRIPTION, REMOTE...............8N-43
KEYLESS ENTRY MODULE - DIAGNOSIS
AND TESTING, REMOTE...............8N-43
KEYLESS ENTRY MODULE -
INSTALLATION, REMOTE..............8N-44
KEYLESS ENTRY MODULE - OPERATION,
REMOTE...........................8N-43
KEYLESS ENTRY MODULE - REMOVAL,
REMOTE...........................8N-44
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING.........8N-42,8N-5
KEYLESS ENTRY TRANSMITTER
PROGRAMMING - STANDARD
PROCEDURE, REMOTE.................8N-5
KEY/LOCK CYLINDER - DESCRIPTION....19-20
KEY/LOCK CYLINDER - INSTALLATION....19-20
KEY/LOCK CYLINDER - OPERATION......19-20
KEY/LOCK CYLINDER - REMOVAL.......19-20
KNOB - INSTALLATION, GEARSHIFT......21-87
KNOB - INSTALLATION, SEAT BELT
HEIGHT ADJUSTER...................8O-14
KNOB - REMOVAL, GEARSHIFT..........21-87
KNOB - REMOVAL, SEAT BELT HEIGHT
ADJUSTER.........................8O-14
KNOCK SENSOR - DESCRIPTION..........8I-8
KNOCK SENSOR - OPERATION...........8I-8
KNUCKLE - DESCRIPTION................2-6
KNUCKLE - INSPECTION, STEERING........2-9
KNUCKLE - INSTALLATION, STEERING......2-9
KNUCKLE - OPERATION.................2-7
KNUCKLE - REMOVAL, STEERING.........2-7
LABEL - DESCRIPTION, E-MARK......Intro.-11
LABEL - DESCRIPTION, VECI.........Intro.-11
LABEL - DESCRIPTION, VEHICLE
CERTIFICATION....................Intro.-11
LABEL - DESCRIPTION, VEHICLE
EMISSION CONTROL INFORMATION.......25-1
LAMP - DESCRIPTION, VTSS/SKIS
INDICATOR..........................8Q-7
LAMP - DIAGNOSIS AND TESTING,
FRONT FOG..........................8L-7
LAMP - INSTALLATION, CENTER
CONSOLE...........................8L-21
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, COURTESY......8L-21
LAMP - INSTALLATION, DOME/CARGO....8L-22
LAMP - INSTALLATION, FRONT FOG.......8L-8
LAMP - INSTALLATION, LICENSE........8L-17
LAMP - INSTALLATION, LIFTGATE.......8L-22
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-18
LAMP - INSTALLATION, READING........8L-23
LAMP - INSTALLATION, TAIL...........8L-19
LAMP - INSTALLATION, VANITY.........8L-24
LAMP - OPERATION, VTSS/SKIS
INDICATOR..........................8Q-8
LAMP - REMOVAL, CENTER CONSOLE....8L-21
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, COURTESY..........8L-21
LAMP - REMOVAL, DOME/CARGO.......8L-22
LAMP - REMOVAL, FRONT FOG..........8L-8
LAMP - REMOVAL, LICENSE............8L-17
LAMP - REMOVAL, LIFTGATE...........8L-22
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-18
LAMP - REMOVAL, READING...........8L-23
LAMP - REMOVAL, TAIL...............8L-18
LAMP - REMOVAL, VANITY.............8L-24
LAMP REPLACEMENT - STANDARD
PROCEDURE, MODULE................8M-3
LAMP REPLACEMENT - STANDARD
PROCEDURE, READING/COURTESY
.......8M-3
LAMP SWITCH - DESCRIPTION, BRAKE
....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE
......................8L-4
LAMP SWITCH - INSTALLATION,
BACK-UP
...........................21-62
LAMP SWITCH - INSTALLATION, BRAKE
. . . 8L-5LAMP SWITCH - INSTALLATION, CENTER
CONSOLE...........................8L-21
LAMP SWITCH - INSTALLATION, GLOVE
BOX ...............................8L-22
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BACK-UP....21-62
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP SWITCH - REMOVAL, CENTER
CONSOLE...........................8L-21
LAMP SWITCH - REMOVAL, GLOVE BOX . . 8L-22
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, TAIL.......8L-19
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, TAIL...........8L-19
LAMP UNIT ALIGNMENT - EXPORT -
STANDARD PROCEDURE, FRONT FOG.....8L-9
LAMP UNIT ALIGNMENT - STANDARD
PROCEDURE, FRONT FOG...............8L-9
LAMPS - INSTALLATION, CLUSTER
ILLUMINATION......................8L-21
LAMPS - REMOVAL, CLUSTER
ILLUMINATION......................8L-21
LAMPS, SPECIFICATIONS - EXTERIOR.....8L-3
LAMPS, SPECIFICATIONS - INTERIOR....8L-20
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-2
LAMPS/LIGHTING - EXTERIOR -
WARNING...........................8L-3
LASH ADJUSTER NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING, HYDRAULIC....9-34
LASH ADJUSTERS - INSTALLATION,
HYDRAULIC..........................9-34
LASH ADJUSTERS - REMOVAL,
HYDRAULIC..........................9-34
LATCH - DESCRIPTION...........8N-13,8N-29
LATCH - INSTALLATION.....23-18,23-41,23-61
LATCH - INSTALLATION..........8N-14,8N-29
LATCH - INSTALLATION, FUEL FILL
DOOR BLOCKER.....................23-53
LATCH - INSTALLATION, GLOVE BOX.....23-64
LATCH - INSTALLATION, HOLD OPEN.....23-25
LATCH / LOCK ASSEMBLY -
INSTALLATION.......................23-27
LATCH / LOCK ASSEMBLY - REMOVAL....23-26
LATCH - OPERATION............8N-13,8N-29
LATCH - REMOVAL.........23-18,23-41,23-61
LATCH - REMOVAL..............8N-13,8N-29
LATCH - REMOVAL, FUEL FILL DOOR
BLOCKER...........................23-53
LATCH - REMOVAL, GLOVE BOX.........23-64
LATCH - REMOVAL, HOLD OPEN........23-25
LATCH ACTUATOR - DESCRIPTION......8N-14
LATCH ACTUATOR - INSTALLATION......8N-14
LATCH ACTUATOR - OPERATION........8N-14
LATCH ACTUATOR - REMOVAL..........8N-14
LATCH CABLE - INSTALLATION, HOLD
OPEN..............................23-38
LATCH CABLE - REMOVAL, HOLD OPEN . . . 23-38
LATCH HANDLE - INSTALLATION, INSIDE . . 23-34
LATCH HANDLE - REMOVAL, INSIDE.....23-34
LATCH LOCKING LINK - INSTALLATION,
SEAT RISER........................23-106
LATCH LOCKING LINK - REMOVAL, SEAT
RISER
............................23-106
LATCH RELEASE CABLE - INSTALLATION
. . 23-62
LATCH RELEASE CABLE - REMOVAL
.....23-61
LATCH STRIKER - INSTALLATION
. . 23-19,23-41,
23-62
LATCH STRIKER - INSTALLATION, FUEL
FILL DOOR BLOCKER
.................23-53
LATCH STRIKER - INSTALLATION, GLOVE
BOX
...............................23-64
LATCH STRIKER - INSTALLATION, HOLD
OPEN
..............................23-26
LATCH STRIKER - INSTALLATION, REAR
. . 23-29
LATCH STRIKER - REMOVAL
. 23-19,23-41,23-62
LATCH STRIKER - REMOVAL, FUEL FILL
DOOR BLOCKER
.....................23-53
LATCH STRIKER - REMOVAL, GLOVE
BOX
...............................23-64
LATCH STRIKER - REMOVAL, HOLD
OPEN
..............................23-26
LATCH STRIKER - REMOVAL, REAR
......23-29LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE..................22-14,22s-6
LEAF SPRING FRONT BUSHING -
INSTALLATION........................2-30
LEAF SPRING FRONT BUSHING -
REMOVAL...........................2-29
LEAK DETECTION ASSY - INSTALLATION,
NATURAL VAC.......................25-13
LEAK DETECTION ASSY - REMOVAL,
NATURAL VAC.......................25-13
LEAK DETECTION PUMP - INSTALLATION . 25-13
LEAK DETECTION PUMP - REMOVAL.....25-13
LEAK DIAGNOSIS, DIAGNOSIS AND
TESTING - FLUID......................21-3
LEAK INSPECTION - DIAGNOSIS AND
TESTING, ENGINE OIL...............9-8,9-82
LEAK REPAIRING - STANDARD
PROCEDURE, TIRE..............22-17,22s-9
LEAK TEST - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-2
LEAKAGE - DIAGNOSIS AND TESTING,
TORQUE CONVERTER HOUSING FLUID . . 21-123,
21s-31
LEAKAGE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION
PRESSURE.......................9-83,9-9
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD...............9-145,9-58
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-66
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEARN CYCLE - STANDARD
PROCEDURE, POWER DOOR.............8N-28
LEARN CYCLE - STANDARD
PROCEDURE, POWER LIFTGATE..........8N-9
LEARN PROCEDURE - STANDARD
PROCEDURE, QUICK.............8E-16,8E-23
LEFT - CLEANING, EXHAUST MANIFOLD . . 9-152
LEFT - INSPECTION, EXHAUST
MANIFOLD..........................9-152
LEFT - INSTALLATION, CYLINDER HEAD
COVER.............................9-103
LEFT - INSTALLATION, EXHAUST
MANIFOLD..........................9-152
LEFT - REMOVAL, CYLINDER HEAD
COVER.............................9-103
LEFT - REMOVAL, EXHAUST MANIFOLD . . . 9-152
LEFT B-PILLAR SWITCH - DESCRIPTION . . 8N-32
LEFT B-PILLAR SWITCH - INSTALLATION . 8N-32
LEFT B-PILLAR SWITCH - OPERATION....8N-32
LEFT B-PILLAR SWITCH - REMOVAL.....8N-32
LEFT D-PILLAR TRIM PANEL -
INSTALLATION.......................23-78
LEFT D-PILLAR TRIM PANEL - REMOVAL . 23-78
LEFT MOUNT - INSTALLATION......9-133,9-50
LEFT MOUNT - REMOVAL..........9-133,9-49
LEFT OUTBOARD - INSTALLATION, SEAT
BELT & RETRACTOR - SECOND ROW....8O-17
LEFT OUTBOARD - REMOVAL, SEAT
BELT & RETRACTOR - SECOND ROW....8O-17
LEFT QUARTER TRIM PANEL -
INSTALLATION.......................23-80
LEFT QUARTER TRIM PANEL - REMOVAL
. 23-80
LENS - INSTALLATION, CLUSTER
........8J-10
LENS - REMOVAL, CLUSTER
............8J-10
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE
......8F-14
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-93
LEVEL AND CONDITION CHECK,
STANDARD PROCEDURE - FLUID
......21-201,
21s-102
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT
.................7-5
LEVEL CHECK - STANDARD
PROCEDURE, ENGINE OIL
..............9-137
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
..................21-71
LEVEL CHECK, STANDARD PROCEDURE
- ENGINE OIL
........................9-53
LEVEL CHECKING - STANDARD
PROCEDURE, BRAKE FLUID
........5-32,5s-31
LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING FLUID
. . . 19-44
LEVEL INSPECTION - STANDARD
PROCEDURE, FLUID
...................21-4
RSINDEX19
Description Group-Page Description Group-Page Description Group-Page

MODULE - DESCRIPTION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - DESCRIPTION, POWER
LIFTGATE CONTROL..................8E-10
MODULE - DESCRIPTION, REAR
DRIVELINE...........................3-23
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - DESCRIPTION, SENTRY KEY
REMOTE ENTRY......................8Q-3
MODULE - DESCRIPTION, SLIDING
DOOR CONTROL.....................8E-19
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-20
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-7
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8E-9
MODULE - DIAGNOSIS AND TESTING,
MEMORY SEAT/MIRROR...............8E-10
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY.............8N-43
MODULE - DIAGNOSIS AND TESTING,
SENTRY KEY REMOTE ENTRY...........8Q-5
MODULE - EXPORT - DESCRIPTION,
ANTENNA...........................8A-6
MODULE - EXPORT - DIAGNOSIS AND
TESTING, ANTENNA...................8A-7
MODULE - EXPORT - INSTALLATION,
ANTENNA...........................8A-7
MODULE - EXPORT - OPERATION,
ANTENNA.............................8A-6
MODULE - EXPORT - REMOVAL,
ANTENNA...........................8A-7
MODULE - INSTALLATION, BODY
CONTROL............................8s-3
MODULE - INSTALLATION, BODY
CONTROL...........................8E-5
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-8
MODULE - INSTALLATION, FUEL PUMP....14-9
MODULE - INSTALLATION, HEATED SEAT . . 8E-10
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-3
MODULE - INSTALLATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - INSTALLATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY.....................8N-44
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-19
MODULE - INSTALLATION, SENTRY KEY
REMOTE ENTRY......................8Q-6
MODULE - INSTALLATION, SLIDING
DOOR CONTROL.....................8E-20
MODULE - INSTALLATION, WIPER.......8R-15
MODULE - OPERATION, BODY CONTROL . . . 8s-1
MODULE - OPERATION, BODY CONTROL . . . 8E-3
MODULE - OPERATION, FRONT
CONTROL...........................8E-7
MODULE - OPERATION, FUEL PUMP
......14-8
MODULE - OPERATION, HEATED SEAT
.....8E-9
MODULE - OPERATION, INTEGRATED
POWER
..........................8W-97-2
MODULE - OPERATION, MEMORY
SEAT/MIRROR
.......................8E-10
MODULE - OPERATION, POWER
LIFTGATE CONTROL
..................8E-11
MODULE - OPERATION, REAR
DRIVELINE
...........................3-23
MODULE - OPERATION, REMOTE
KEYLESS ENTRY
.....................8N-43
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER
.......................8E-18
MODULE - OPERATION, SENTRY KEY
REMOTE ENTRY
......................8Q-4
MODULE - OPERATION, SLIDING DOOR
CONTROL
..........................8E-19
MODULE - OPERATION, TRANSMISSION
CONTROL
..........................8E-20
MODULE - REAR BLOWER MOTOR -
DESCRIPTION, POWER
................24-41
MODULE - REAR BLOWER MOTOR -
INSTALLATION, POWER
...............24-42MODULE - REAR BLOWER MOTOR -
OPERATION, POWER..................24-41
MODULE - REAR BLOWER MOTOR -
REMOVAL, POWER...................24-41
MODULE - REMOVAL, BODY CONTROL....8s-3
MODULE - REMOVAL, BODY CONTROL....8E-4
MODULE - REMOVAL, FRONT CONTROL . . . 8E-8
MODULE - REMOVAL, FUEL PUMP........14-8
MODULE - REMOVAL, HEATED SEAT......8E-9
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-2
MODULE - REMOVAL, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - REMOVAL, POWER LIFTGATE
CONTROL..........................8E-11
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY.............................8N-44
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - REMOVAL, SENTRY KEY
REMOTE ENTRY......................8Q-5
MODULE - REMOVAL, SLIDING DOOR
CONTROL..........................8E-19
MODULE - REMOVAL, WIPER...........8R-15
MODULE - SPECIFICATIONS, REAR
DRIVELINE...........................3-34
MODULE, BENCH SEAT - REMOVAL,
CHILD SEAT.........................23-87
MODULE FLUIDS - DESCRIPTION, AWD
REAR DRIVELINE......................0-6
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE.................8M-3
MODULE NOISE - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-24
MODULE OPERATION - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-26
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT..................23-115
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT..................23-113
MOLDING - INSTALLATION, ROOF JOINT . . 23-58
MOLDING - REMOVAL, FRONT DOOR
INNER BELT........................23-115
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT.......................23-113
MOLDING - REMOVAL, ROOF JOINT......23-58
MOLDINGS - INSTALLATION, BODY SIDE . . 23-46
MOLDINGS - REMOVAL, BODY SIDE.....23-45
MONITORED COMPONENT -
DESCRIPTION........................25-1
MONITORED SYSTEMS - DESCRIPTION....25-6
MONITORING - DESCRIPTION, TIRE
PRESSURE.....................22-9,22s-1
MONITORING - OPERATION, TIRE
PRESSURE.....................22-9,22s-1
MOTOR - DESCRIPTION, BLOWER . . 24-46,24-57
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-28
MOTOR - DESCRIPTION, LIFTGATE......8N-15
MOTOR - DESCRIPTION, POWER
MODULE - BLOWER..................24-31
MOTOR - DESCRIPTION, POWER
MODULE - REAR BLOWER.............24-41
MOTOR - DESCRIPTION, SLIDING DOOR . . 8N-30
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-47
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
MOTOR - DIAGNOSIS AND TESTING,
RADIATOR FAN.......................7-29
MOTOR - DIAGNOSIS AND TESTING,
REAR BLOWER......................24-58
MOTOR - DIAGNOSIS AND TESTING,
VENT WINDOW......................8N-63
MOTOR - INSTALLATION, BLOWER . 24-49,24-58
MOTOR - INSTALLATION, FRONT
WASHER PUMP......................8R-8
MOTOR - INSTALLATION, FRONT WIPER . . . 8R-9
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-29
MOTOR - INSTALLATION, LIFTGATE
......8N-15
MOTOR - INSTALLATION, POWER
MODULE - BLOWER
..................24-32
MOTOR - INSTALLATION, POWER
MODULE - REAR BLOWER
.............24-42
MOTOR - INSTALLATION, REAR WASHER
PUMP
.............................8R-10
MOTOR - INSTALLATION, REAR WIPER
. . . 8R-11MOTOR - INSTALLATION, SLIDING DOOR . 8N-31
MOTOR - INSTALLATION, SLIDING DOOR
LOCK.........................8N-44,8N-6
MOTOR - INSTALLATION, SUNROOF.....23-121
MOTOR - INSTALLATION, VENT WINDOW . 8N-64
MOTOR - OPERATION, BLOWER....24-46,24-57
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-28
MOTOR - OPERATION, LIFTGATE........8N-15
MOTOR - OPERATION, POWER MODULE
- BLOWER..........................24-31
MOTOR - OPERATION, POWER MODULE
- REAR BLOWER.....................24-41
MOTOR - OPERATION, SLIDING DOOR . . . 8N-30
MOTOR - REMOVAL, BLOWER.....24-47,24-58
MOTOR - REMOVAL, FRONT WASHER
PUMP..............................8R-8
MOTOR - REMOVAL, FRONT WIPER......8R-9
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-29
MOTOR - REMOVAL, LIFTGATE.........8N-15
MOTOR - REMOVAL, POWER MODULE -
BLOWER...........................24-31
MOTOR - REMOVAL, POWER MODULE -
REAR BLOWER......................24-41
MOTOR - REMOVAL, REAR WASHER
PUMP.............................8R-10
MOTOR - REMOVAL, REAR WIPER......8R-11
MOTOR - REMOVAL, SLIDING DOOR.....8N-30
MOTOR - REMOVAL, SLIDING DOOR
LOCK...........................8N-44,8N-6
MOTOR - REMOVAL, SUNROOF........23-121
MOTOR - REMOVAL, VENT WINDOW.....8N-63
MOTOR - REMOVAL, WINDOW..........8N-64
MOTOR RELAY - DESCRIPTION,
BLOWER......................24-24,24-37
MOTOR RELAY - INSTALLATION,
BLOWER......................24-25,24-38
MOTOR RELAY - OPERATION, BLOWER . . 24-24,
24-37
MOTOR RELAY - REMOVAL, BLOWER....24-25,
24-38
MOTOR RESISTOR - DESCRIPTION,
BLOWER...........................24-38
MOTOR RESISTOR - INSTALLATION,
BLOWER...........................24-39
MOTOR RESISTOR - OPERATION,
BLOWER...........................24-38
MOTOR RESISTOR - REMOVAL,
BLOWER...........................24-39
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, REAR BLOWER..........24-38
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER..............24-27
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER...........................24-26
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER...........................24-26
MOUNT - INSTALLATION, FRONT....9-131,9-49
MOUNT - INSTALLATION, LEFT......9-133,9-50
MOUNT - INSTALLATION, REAR.....9-134,9-50
MOUNT - INSTALLATION, RIGHT....9-135,9-51
MOUNT - REMOVAL, FRONT........9-131,9-49
MOUNT - REMOVAL, LEFT.........9-133,9-49
MOUNT - REMOVAL, REAR.........9-133,9-50
MOUNT - REMOVAL, RIGHT........9-135,9-51
MOUNT BUSHINGS - INSTALLATION,
FRONT CROSSMEMBER...............13-12
MOUNT BUSHINGS - REMOVAL, FRONT
CROSSMEMBER.....................13-12
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH...........8L-6
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH
...............8L-6
MOUNTING - DESCRIPTION, ENGINE
. 9-131,9-48
MOUNTING - STANDARD PROCEDURE,
TIRE AND WHEEL MATCH
...............22-7
MOUNTING BRACKET - 2.4L ENGINE -
INSTALLATION, A/C COMPRESSOR
.......24-76
MOUNTING BRACKET - 2.4L ENGINE -
REMOVAL, A/C COMPRESSOR
..........24-75
22 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

MOUNTING STUDS - FRONT -
INSTALLATION, WHEEL................22-21
MOUNTING STUDS - FRONT - REMOVAL,
WHEEL............................22-20
MOUNTING STUDS - REAR -
INSTALLATION, WHEEL................22-22
MOUNTING STUDS - REAR - REMOVAL,
WHEEL............................22-21
MOUNTS - FRONT - INSTALLATION,
SPRING.............................2-44
MOUNTS - FRONT - REMOVAL, SPRING . . . 2-43
MOUNTS - REAR - INSTALLATION,
SPRING.............................2-45
MOUNTS - REAR - REMOVAL, SPRING....2-44
MUFFLER - INSTALLATION..............11-7
MUFFLER - REMOVAL..................11-7
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-18
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-18
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - ADHESIVE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - ADHESIVE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NAME PLATES - TAPE ATTACHED -
INSTALLATION, EXTERIOR.............23-51
NAME PLATES - TAPE ATTACHED -
REMOVAL, EXTERIOR.................23-51
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-13
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-13
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP TO FILLER..............7-27
NGC CONTROLLER - REMOVAL.........8E-17
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-47
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-47
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-47
NO CUPHOLDER - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NO CUPHOLDER - REMOVAL, QUAD
BUCKET SEAT SIDE SHIELD............23-97
NOISE - DIAGNOSIS AND TESTING,
EXCESSIVE EXHAUST SYSTEM...........11-2
NOISE - DIAGNOSIS AND TESTING,
REAR DRIVELINE MODULE..............3-24
NOISE - DIAGNOSIS AND TESTING, TIRE . 22-14,
22s-6
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-74
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, HYDRAULIC LASH
ADJUSTER...........................9-34
NOISE SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO.................8A-11
NOISE SUPPRESSION COMPONENTS -
OPERATION, RADIO..................8A-12
NON-ABS JUNCTION BLOCK -
DESCRIPTION...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
INSTALLATION
...................5-33,5s-32
NON-ABS JUNCTION BLOCK -
OPERATION
.....................5-33,5s-32
NON-ABS JUNCTION BLOCK - REMOVAL
. . 5-33,
5s-32
NON-MONITORED CIRCUITS -
OPERATION
..........................25-5
NOT FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES
......................25-16
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION
....................Intro.-9
NVLD - INSTALLATION, WITH
...........25-20
NVLD - REMOVAL, WITH
..............25-19
O2 SENSOR - DESCRIPTION
............14-32
O2 SENSOR - OPERATION
.............14-32
OBTAINING DIAGNOSTIC TROUBLE
CODES - STANDARD PROCEDURE
.......8E-15
OCCUPANT RESTRAINT CONTROLLER -
DESCRIPTION
........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
INSTALLATION
.......................8O-8OCCUPANT RESTRAINT CONTROLLER -
OPERATION..........................8O-8
OCCUPANT RESTRAINT CONTROLLER -
REMOVAL...........................8O-8
OIL - DESCRIPTION, FLEXIBLE FUEL
ENGINE..............................0-3
OIL - DESCRIPTION, REFRIGERANT......24-92
OIL - DIESEL ENGINES - DESCRIPTION,
ENGINE..............................0-6
OIL - OPERATION, REFRIGERANT........24-92
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE.............9-137,9-53
OIL AND LUBRICANTS - DESCRIPTION,
ENGINE..............................0-1
OIL COOLER - DESCRIPTION,
TRANSMISSION.......................7-37
OIL COOLER - INSPECTION,
TRANSMISSION.......................7-37
OIL COOLER - INSTALLATION,
TRANSMISSION.......................7-37
OIL COOLER & LINES - DESCRIPTION....9-138
OIL COOLER & LINES - INSTALLATION . . . 9-138
OIL COOLER & LINES - OPERATION......9-138
OIL COOLER & LINES - REMOVAL.......9-138
OIL COOLER - REMOVAL,
TRANSMISSION.......................7-37
OIL COOLER LINES - INSTALLATION,
TRANSMISSION.......................7-38
OIL COOLER LINES - REMOVAL,
TRANSMISSION.......................7-38
OIL FILTER - DESCRIPTION.............9-53
OIL FILTER - INSTALLATION........9-139,9-53
OIL FILTER - REMOVAL............9-139,9-53
OIL FILTER ADAPTER - INSTALLATION....9-139
OIL FILTER ADAPTER - REMOVAL.......9-139
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE.........9-10,9-86
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..............9-8,9-82
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-93
OIL LEVEL CHECK - STANDARD
PROCEDURE, ENGINE.................9-137
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-53
OIL PAN - CLEANING.................9-140
OIL PAN - INSPECTION................9-140
OIL PAN - INSTALLATION..........9-140,9-54
OIL PAN - REMOVAL..............9-140,9-54
OIL PRESSURE - DIAGNOSIS AND
TESTING, CHECKING ENGINE............9-52
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE....................9-136
OIL PRESSURE RELIEF VALVE -
INSTALLATION.......................9-141
OIL PRESSURE RELIEF VALVE -
REMOVAL..........................9-141
OIL PRESSURE SWITCH - DESCRIPTION . . 9-141
OIL PRESSURE SWITCH - INSTALLATION . 9-141,
9-54
OIL PRESSURE SWITCH - OPERATION....9-141
OIL PRESSURE SWITCH - REMOVAL . 9-141,9-54
OIL PUMP - ASSEMBLY...........9-143,9-56
OIL PUMP - ASSEMBLY.......21-232,21s-132
OIL PUMP - CLEANING............9-142,9-56
OIL PUMP - DESCRIPTION.............9-142
OIL PUMP - DESCRIPTION.....21-230,21s-131
OIL PUMP - DISASSEMBLY........9-142,9-55
OIL PUMP - DISASSEMBLY.....21-230,21s-131
OIL PUMP - INSPECTION..........9-142,9-56
OIL PUMP - INSTALLATION........9-144,9-57
OIL PUMP - INSTALLATION, SEAL......21-233,
21s-133
OIL PUMP - OPERATION.......21-230,21s-131
OIL PUMP - REMOVAL............9-142,9-55
OIL PUMP - REMOVAL, SEAL . . . 21-232,21s-133
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT...................9-127,9-40
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT
...................9-127,9-40
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT
...................9-129,9-42
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT
...................9-128,9-41
OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR
..................9-129
OIL SEAL RETAINER - REMOVAL,
CRANKSHAFT REAR
..................9-129OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-28
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-27
ON-BOARD DIAGNOSTIC SYSTEM -
DIAGNOSIS AND TESTING..............8F-21
OPEN LATCH - INSTALLATION, HOLD.....23-25
OPEN LATCH - REMOVAL, HOLD........23-25
OPEN LATCH CABLE - INSTALLATION,
HOLD..............................23-38
OPEN LATCH CABLE - REMOVAL, HOLD . . . 23-38
OPEN LATCH STRIKER - INSTALLATION,
HOLD..............................23-26
OPEN LATCH STRIKER - REMOVAL,
HOLD..............................23-26
OPEN SWITCH - DESCRIPTION, FULL....8N-12,
8N-31
OPEN SWITCH - INSTALLATION, FULL....8N-13
OPEN SWITCH - OPERATION, FULL . 8N-12,8N-31
OPEN SWITCH - REMOVAL, FULL.......8N-13
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-13
OPENING DIMENSIONS -
SPECIFICATIONS, BODY..............23-127
OPENING REINFORCEMENT -
INSTALLATION, GRILLE................23-54
OPENING REINFORCEMENT - REMOVAL,
GRILLE............................23-54
ORDER, SPECIFICATIONS - FIRING........8I-3
O-RING - INSTALLATION, REAR COVER . . . 21-20
O-RING - REMOVAL, REAR COVER.......21-19
ORVR - OPERATION..................25-14
OUTBOARD - FRONT - INSTALLATION,
SEAT BELT & RETRACTOR.............8O-14
OUTBOARD - FRONT - REMOVAL, SEAT
BELT & RETRACTOR..................8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - FIRST ROW...........8O-14
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW - LEFT . . . 8O-17
OUTBOARD - INSTALLATION, SEAT BELT
& RETRACTOR - SECOND ROW -
RIGHT.............................8O-15
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - FIRST ROW.............8O-14
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - LEFT.....8O-17
OUTBOARD - REMOVAL, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-15
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR - SECOND ROW - RIGHT....8O-16
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT & RETRACTOR -
SECOND ROW - RIGHT................8O-16
OUTER - INSTALLATION, CV BOOT........3-10
OUTER - REMOVAL, CV BOOT...........3-10
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-113
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-113
OUTER HALF SHAFT SEAL -
INSTALLATION.......................21-19
OUTER HALF SHAFT SEAL - REMOVAL . . . 21-19
OUTER TIE ROD - INSTALLATION........19-34
OUTER TIE ROD - REMOVAL...........19-34
OUTLET - DESCRIPTION, POWER......8W-97-4
OUTLET - DIAGNOSIS & TESTING,
POWER..........................8W-97-4
OUTLET - INSTALLATION, DEMISTER
.....24-46
OUTLET - INSTALLATION, INSTRUMENT
PANEL
.............................24-46
OUTLET - OPERATION, POWER
.......8W-97-4
OUTLET - REMOVAL, DEMISTER
........24-45
OUTLET - REMOVAL, INSTRUMENT
PANEL
.............................24-45
OUTLETS - DESCRIPTION, AIR
.....24-44,24-56
OUTLETS - INSTALLATION, AIR
.........24-56
OUTLETS - INSTALLATION, CENTER
BEZEL
.............................24-45
OUTLETS - REMOVAL, AIR
.............24-56
OUTLETS - REMOVAL, CENTER BEZEL
....24-44
OUTPUT - DESCRIPTION, SPEED
SENSOR
....................21-241,21s-142
OUTPUT - INSTALLATION, SPEED
SENSOR
....................21-242,21s-143
OUTPUT - OPERATION, 5 VOLT SUPPLY -
PCM
...............................8E-15
RSINDEX23
Description Group-Page Description Group-Page Description Group-Page

POWER TRANSFER UNIT, SPECIAL
TOOLS - SDP........................21-8
POWER WINDOWS - DESCRIPTION......8N-62
POWER WINDOWS - DIAGNOSIS AND
TESTING...........................8N-62
POWER WINDOWS - OPERATION........8N-62
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY...................23-1
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY................23-108
PREFERENCE - STANDARD PROCEDURE,
HORN CHIRP...................8N-42,8N-5
PRELOAD - ADJUSTMENT,
DIFFERENTIAL BEARING..............21-199
PRELOAD MEASUREMENT AND
ADJUSTMENT, ADJUSTMENTS -
DIFFERENTIAL BEARING.............21s-100
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE........................9-11,9-85
PRESSURE - DIAGNOSIS AND TESTING,
CHECKING ENGINE OIL.................9-52
PRESSURE - DIAGNOSIS AND TESTING,
ENGINE OIL.........................9-136
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-26
PRESSURE CAP - OPERATION,
RADIATOR...........................7-27
PRESSURE CAP TESTING - DIAGNOSIS
AND TESTING, COOLING SYSTEM........7-27
PRESSURE FOR HIGH SPEED
OPERATION - STANDARD PROCEDURE,
TIRE..........................22-17,22s-9
PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION.....................9-83,9-9
PRESSURE MONITORING -
DESCRIPTION, TIRE..............22-9,22s-1
PRESSURE MONITORING - OPERATION,
TIRE...........................22-9,22s-1
PRESSURE PLATE - 2.5L TD -
INSTALLATION, CLUTCH DISC...........6-12
PRESSURE PLATE - 2.5L TD - REMOVAL,
CLUTCH DISC........................6-11
PRESSURE REGULATOR -
INSTALLATION, FUEL..................14-7
PRESSURE REGULATOR - OPERATION,
FUEL...............................14-7
PRESSURE REGULATOR - REMOVAL,
FUEL...............................14-7
PRESSURE RELEASE PROCEDURE -
STANDARD PROCEDURE, FUEL
SYSTEM............................14-2
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-73
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-141
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-73
PRESSURE RELIEF VALVE - REMOVAL,
OIL
................................9-141
PRESSURE SENSOR - DIAGNOSIS AND
TESTING, TIRE
..................22-10,22s-2
PRESSURE SENSOR RETRAIN -
STANDARD PROCEDURE, TIRE
.....22-10,22s-2
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM
............................14-3
PRESSURE SWITCH - DESCRIPTION, OIL
. 9-141
PRESSURE SWITCH - INSTALLATION,
OIL
...........................9-141,9-54
PRESSURE SWITCH - OPERATION, OIL
. . . 9-141
PRESSURE SWITCH - REMOVAL, OIL
....9-141,
9-54
PRESSURE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMPRESSION
. . . 9-83,9-9
PRESSURE TEST - DIAGNOSIS AND
TESTING, POWER STEERING SYSTEM
FLOW
...............................19-1
PRESSURE TESTS - DIAGNOSIS AND
TESTING, CLUTCH AIR
.........21-122,21s-30
PRESSURE TESTS - DIAGNOSIS AND
TESTING, HYDRAULIC
..........21-120,21s-28
PRESSURE TRANSDUCER -
DESCRIPTION, A/C
...................24-21PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-22
PRESSURE TRANSDUCER -
INSTALLATION, A/C...................24-22
PRESSURE TRANSDUCER - OPERATION,
A/C................................24-21
PRESSURE TRANSDUCER - REMOVAL,
A/C................................24-22
PRESSURES - STANDARD PROCEDURE,
TIRE INFLATION.................22-16,22s-8
PROBLEM CAUSES - DIAGNOSIS AND
TESTING, COMMON..................21-30
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER.......8N-43
PROGRAMMABLE COMMUNICATIONS
INTERFACE (PCI) BUS, OPERATION......14-21
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER................8M-7
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM................8E-2
PROGRAMMING - STANDARD
PROCEDURE, REMOTE KEYLESS
ENTRY TRANSMITTER.................8N-5
PROGRAMMING - STANDARD
PROCEDURE, TRANSPONDER...........8Q-6
PROPELLER SHAFT - DESCRIPTION.......3-21
PROPELLER SHAFT - INSTALLATION......3-22
PROPELLER SHAFT - OPERATION........3-21
PROPELLER SHAFT - REMOVAL..........3-21
PROPELLER SHAFT - SPECIFICATIONS.....3-22
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE............5-75
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-77
PROPORTIONING VALVE (HEIGHT
SENSING) - DESCRIPTION.........5-48,5s-51
PROPORTIONING VALVE (HEIGHT
SENSING) - DIAGNOSIS AND TESTING....5-49,
5s-52
PROPORTIONING VALVE (HEIGHT
SENSING) - INSTALLATION.........5-51,5s-53
PROPORTIONING VALVE (HEIGHT
SENSING) - OPERATION...........5-48,5s-51
PROPORTIONING VALVE (HEIGHT
SENSING) - REMOVAL............5-50,5s-53
PTU FLUID CHANGE - STANDARD
PROCEDURE.........................21-5
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER....................8F-25,8F-27
PULLEY - DIAGNOSIS AND TESTING,
GENERATOR DECOUPLER.........8F-25,8F-27
PULLEY - INSTALLATION, GENERATOR
DECOUPLER....................8F-26,8F-28
PULLEY - INSTALLATION, TIMING BELT
TENSIONER..........................9-69
PULLEY - OPERATION, GENERATOR
DECOUPLER....................8F-25,8F-27
PULLEY - REMOVAL, GENERATOR
DECOUPLER....................8F-26,8F-28
PULLEY - REMOVAL, TIMING BELT
TENSIONER..........................9-68
PUMP - 2.4L - CLEANING, WATER........7-32
PUMP - 2.4L - DESCRIPTION, WATER.....7-31
PUMP - 2.4L - INSPECTION, WATER......7-32
PUMP - 2.4L - INSTALLATION, WATER.....7-32
PUMP - 2.4L - REMOVAL, WATER........7-31
PUMP - 3.3/3.8L - CLEANING, WATER.....7-34
PUMP - 3.3/3.8L - DESCRIPTION,
WATER .............................7-33
PUMP - 3.3/3.8L - INSPECTION, WATER . . . 7-34
PUMP - 3.3/3.8L - INSTALLATION,
WATER .............................7-34
PUMP - 3.3/3.8L - REMOVAL, WATER.....7-33
PUMP - ASSEMBLY, OIL...........9-143,9-56
PUMP - ASSEMBLY, OIL.......21-232,21s-132
PUMP - CLEANING, OIL...........9-142,9-56
PUMP - DESCRIPTION, FUEL............14-8
PUMP - DESCRIPTION, FUEL DOSING . . . 24-115
PUMP - DESCRIPTION, OIL.............9-142
PUMP - DESCRIPTION, OIL.....21-230,21s-131
PUMP - DISASSEMBLY, OIL........9-142,9-55
PUMP - DISASSEMBLY, OIL
....21-230,21s-131
PUMP - INSPECTION, OIL
..........9-142,9-56
PUMP - INSTALLATION, FUEL DOSING
. . . 24-116
PUMP - INSTALLATION, LEAK
DETECTION
.........................25-13
PUMP - INSTALLATION, OIL
........9-144,9-57PUMP - INSTALLATION, SEAL - OIL....21-233,
21s-133
PUMP - OPERATION, FUEL..............14-8
PUMP - OPERATION, FUEL DOSING.....24-115
PUMP - OPERATION, OIL......21-230,21s-131
PUMP - REMOVAL, FUEL DOSING......24-115
PUMP - REMOVAL, LEAK DETECTION....25-13
PUMP - REMOVAL, OIL............9-142,9-55
PUMP - REMOVAL, SEAL - OIL . . 21-232,21s-133
PUMP (2.4L ENGINE) - INSTALLATION....19-42
PUMP (2.4L ENGINE) - REMOVAL.......19-38
PUMP (2.4L/3.3L/3.8L ENGINE) -
DESCRIPTION.......................19-36
PUMP (2.5L DIESEL) - DESCRIPTION.....19-36
PUMP (2.5L DIESEL) - INSTALLATION....19-43
PUMP (2.5L DIESEL) - REMOVAL........19-40
PUMP (3.3L/3.8L ENGINE) -
INSTALLATION.......................19-43
PUMP (3.3L/3.8L ENGINE) - REMOVAL . . . 19-40
PUMP INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING........19-37
PUMP INLET TUBE - 2.4L -
DESCRIPTION, WATER.................7-35
PUMP INLET TUBE - 2.4L -
INSTALLATION, WATER.................7-35
PUMP INLET TUBE - 2.4L - REMOVAL,
WATER .............................7-35
PUMP INLET TUBE - 3.3/3.8L -
INSTALLATION, WATER.................7-36
PUMP INLET TUBE - 3.3/3.8L -
REMOVAL, WATER....................7-36
PUMP MODULE - DESCRIPTION, FUEL....14-8
PUMP MODULE - INSTALLATION, FUEL....14-9
PUMP MODULE - OPERATION, FUEL......14-8
PUMP MODULE - REMOVAL, FUEL........14-8
PUMP MOTOR - INSTALLATION, FRONT
WASHER............................8R-8
PUMP MOTOR - INSTALLATION, REAR
WASHER...........................8R-10
PUMP MOTOR - REMOVAL, FRONT
WASHER............................8R-8
PUMP MOTOR - REMOVAL, REAR
WASHER...........................8R-10
PUMP (PULLEY) - ASSEMBLY..........19-41
PUMP (PULLEY) - DISASSEMBLY........19-41
PUMP RELAY - DESCRIPTION, FUEL.....14-28
PUMP RELAY - OPERATION, FUEL.......14-28
PUMP, SPECIAL TOOLS - POWER
STEERING..........................19-43
PUSH-PIN GROMMET REPLACEMENT -
STANDARD PROCEDURE..............8N-28
PUSHRODS - DESCRIPTION.......9-109,9s-26
PUSHRODS - OPERATION.........9-109,9s-26
QUAD BUCKET - INSTALLATION, BUCKET
SEAT BACK.........................23-99
QUAD BUCKET - INSTALLATION, SEAT
BELT BUCKLE - FIRST ROW INBOARD....8O-12
QUAD BUCKET - REMOVAL, BUCKET
SEAT BACK.........................23-98
QUAD BUCKET - REMOVAL, SEAT BELT
BUCKLE - FIRST ROW INBOARD........8O-12
QUAD BUCKET, 50/50 SPLIT, BENCH -
INSTALLATION, SEAT BACK HINGE
COVERS...........................23-101
QUAD BUCKET, 50/50 SPLIT, BENCH -
INSTALLATION, SEAT CUSHION COVER . . 23-100
QUAD BUCKET, 50/50 SPLIT, BENCH -
REMOVAL, SEAT BACK HINGE COVERS . . 23-101
QUAD BUCKET, 50/50 SPLIT, BENCH -
REMOVAL, SEAT CUSHION COVER......23-100
QUAD BUCKET SEAT RISER -
INSTALLATION.......................23-98
QUAD BUCKET SEAT RISER - REMOVAL . . 23-98
QUAD BUCKET SEAT SIDE SHIELD - NO
CUPHOLDER - INSTALLATION...........23-97
QUAD BUCKET SEAT SIDE SHIELD - NO
CUPHOLDER - REMOVAL..............23-97
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - FLAP AND SPRING
ASSEMBLY - INSTALLATION
...........23-107
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - FLAP AND SPRING
ASSEMBLY - REMOVAL
...............23-107
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - INSTALLATION
...........23-96
QUAD BUCKET SEAT SIDE SHIELD/
CUPHOLDER - REMOVAL
..............23-96
QUAD CHILD SEAT - INSTALLATION
......23-89
26 INDEXRS
Description Group-Page Description Group-Page Description Group-Page