2004 CHRYSLER CONCORDE lock

▫Fuel System Hoses....................217
▫Automatic Transaxle...................217
▫Appearance Care And Protection From
Corrosion...........................220
Fuses...............................224
▫Fuse Block Relays.....................224
▫Underhood Fuses.....................224
Replacement Light Bulbs................226
Bulb Replacement......................227
▫Headlight, Parking Light Replacement......227
▫Front Park And Turn Signal Light..........230
▫Front Sidemarker Light.................230▫Fog Light...........................230
▫Center Stop Light.....................231
▫Tail, Stop, Back Up, And Turn Signal Lights . . 231
▫License Plate Light....................232
Specifications.........................232
Fluid Capacities.......................233
Recommended Fluids, Lubricants And
Genuine Parts
.........................233
▫Engine.............................233
▫Chassis............................234
▫Body..............................234
188 MAINTAINING YOUR VEHICLE

External Lock Cylinders
Lubricate the external lock cylinders twice a year, prefer-
ably in the fall and spring. Apply a small amount of
lubricant, such as Mopar Lock Cylinder Lubricant di-
rectly into the lock cylinder (avoid excess lubricant).
Insert the key into the lock cylinder and rotate from the
unlocked to the locked position; without adding more
lubricant. Repeat this procedure three or four times. Wipe
all the lubricant off the key with a clean cloth, to avoid
soiling clothing.
If you use a lubricant that cannot be dispensed directly
into the lock cylinder, apply a small amount of the
lubricant to the key. Insert the key into the lock cylinder,
then proceed as described above, to distribute the lubri-
cant within the lock cylinder. Pay attention to trunk
hinges, especially during cold weather, to ensure ease of
trunk operation.
Other Body Mechanisms
The following body mechanisms should be inspected
and, if necessary, all pivot and sliding contact areas of
these components should be lubricated with the lubricant
specified as follows:
Engine Oil
•
Door hinges
•Hood hinges
•Trunk hinges
Smooth White Body Lubricant - Such as Mopar
Spray White Lube:
•
Hood hinge springs and links
•Lock cylinders
•Parking brake mechanism
•Trunk latches
•Ash tray
•Door Check Straps
208 MAINTAINING YOUR VEHICLE

FUSES
The fuse block is behind the end cover at the left side of
the instrument panel. Pull the cover straight away from
the instrument panel for access to the fuses.
Fuse Block Relays
The location and identification of fuse block relays can be
found on the inside of the instrument panel end cover.
Underhood Fuses
A Power Distribution center is located in the engine
compartment. This center contains fuses and relays for
circuits that operate only under the hood. A label which
identifies these components is located on the underside
of the cover.
224 MAINTAINING YOUR VEHICLE

Cavity Fuse Circuits
18 20 Amp Yel-
lowPower Amplifier, Horn
19 15 Amp Lt.
BlueOverhead Console, Garage
Door Opener, Trunk, Over-
head, Rear Reading, and Visor
Vanity Lights, Trunk Release
Solenoid, Power Mirrors,
Power Door Locks, Body Con-
trol Module, Aspirator Motor
20 20 Amp Yel-
lowBrake Lights
21 10 Amp Red Leak Detection Pump, Low
Rad Relay, High Rad Relay,
A/C Clutch Relay
22 10 Amp Red Airbag
23 30 Amp
GreenBlower Motor, ATC Power
Module
24 20 Amp
C/BRKRPower Window Motors
25 20 Amp
C/BRKRPower Door Lock Motors,
Power SeatsREPLACEMENT LIGHT BULBS
Interior Light Bulbs Bulb No.
Turn Signal...........................PC194
Climate Control.......................... 330
Overhead Console, Front Reading, Courtesy, Grab
Handle................................ 192
Trunk................................. 906
Exterior Light Bulbs Bulb No.
Low Beam Headlights....................9006
High Beam Headlights................9005XSLL
Park, Turn, & Side Marker................3157A
Fog Lights.............................9040
Center Stop Light........................ 921
Tail, Stop, & Turn......................3157K
Back-Up............................... 921
License................................ 168
Front Sidemarker......................... 168
Tail.................................. 916
226 MAINTAINING YOUR VEHICLE

5. Remove the speed control servo screw. 6. Lift and prop the crossmember above the headlamp on
the side being serviced, and remove the electrical con-
nectors from the headlamp.
7. Pull headlamp up and under crossmember to remove
it from the vehicle.
8. Remove the bulb retaining ring by turning it counter-
clockwise. Pull the bulb and socket assembly from the
housing and pull the bulb from the socket.
9. Install a new headlight bulb in the socket, reinstall the
bulb and socket assembly and tighten the retaining ring.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life.
If the bulb comes into contact with any oily surface,
clean the bulbs with rubbing alcohol.
10. Reinstall the headlight assembly, replace the electri-
cal connectors from the headlamp and lower the cross-
member back on the headlamp.
MAINTAINING YOUR VEHICLE 229
7

11. Reinstall the upper crossmember attachments, head-
lamp jackscrews, windshield filler neck screw and speed
control servo screw.
Front Park and Turn Signal Light
1. Remove the headlight assembly from the vehicle.
2. Turn the park/turn signal bulb and socket assembly
counterclockwise and remove it from the housing.
3. Pull the bulb from the socket and install a new bulb.
4. Reinstall the bulb and socket assembly.
5. Reinstall the headlight assembly.
Front Sidemarker Light
1. Reach up under the fascia and grasp the light bulb
socket.
2. Turn the socket counterclockwise to remove it from
the housing.
3. Pull the bulb out of the socket.
4. Replace the bulb and reinstall the socket. Turn the
socket clockwise to secure it in the housing.
Fog Light
1. Remove the screw securing the fog light to the fascia
and pull the light away from the vehicle to expose the
bulb.
2. Remove the bulb by turning counter-clockwise. Pull
the bulb out of the light housing.
3. Remove the wiring connector from the bulb.
4. Insert new bulb and turn clockwise.
230 MAINTAINING YOUR VEHICLE

5. Connect the wiring connector to the new bulb and
reinstall the assembly.
Center Stop Light
1. Open the trunk and reach up under the package shelf.
2. Turn the bulb socket counterclockwise and remove it
from the housing.
3. Pull the bulb from the socket and replace the bulb.
4. Reinstall the bulb and socket assembly.
Tail, Stop, Back Up, and Turn Signal Lights
1. Open the trunk and remove the fasteners securing the
light housing to the body.
2. Pull the light housing from the body to expose the
wiring socket.
3. Turn the bulb socket counterclockwise to remove from
the housing. Pull the bulb out of the socket and remove
the bulb.
4. Replace the bulb, reinstall the bulb and socket assem-
bly and reattach the light housing.
MAINTAINING YOUR VEHICLE 231
7

Chassis
Component Fluid, Lubricant or Genuine Part
Automatic Transmission MoparATF+4 Automatic Transmission Fluid.
Axle Differential (front-rear) MoparHypoid Gear Lubricant (SAE 80W-90). Do not use synthetic gear lu-
bricants.
Brake Master Cylinder MoparDOT-3 Brake Fluid.
Power Steering Reservoir MoparATF+4 Automatic Transmission Fluid.
Tire Pressure Refer to label on driver’s door pillar.
Body
Component Fluid, Lubricant or Genuine Part
Hinges:
Door, Hood and Trunk MoparEngine Oil
Hood hinge springs and links MoparSpray White Lube
Latches:
Door and Hood Trunk MoparMulti-Purpose Lube NLGI Grade 2 MoparSpray White Lube
Door check straps MoparSpray White Lube
Window System Components MoparSpray White Lube
Lock Cylinders MoparSpray White Lube
Parking Brake Mechanism MoparSpray White Lube
234 MAINTAINING YOUR VEHICLE