2004 BMW X3 3.0I lock

Reference
At a glance
Controls
Driving tips
Mobility
27
Adjustments
Sitting safely
The ideal sitting position can make a vital
contribution to relaxed driving that is as
fatigue-free as possible. The sitting posi-
tion plays an important role together with
the safety belts and airbags in providing
occupants with maximum levels of passive
safety in an accident. Therefore, observe
the following instructions, as otherwise the
protective function of the safety systems
may be impaired.
For additional information on transporting
children safely, refer to page 34.
Sitting safely with airbags
Always maintain an adequate dis-
tance between yourself and the air-
bags. Always hold the steering wheel by
its rim with hands at the 9 o'clock and
3 o'clock positions, to minimize the risk of
injuries to your hands and arms in the event
of airbag deployment.
No one and nothing is to come between the
airbags and the seat occupant.
Do not use the cover of the front airbag on
the front passenger side as a storage area.
Make sure that the front passenger is cor-
rectly seated, i.e. feet or legs not resting on
the instrument panel, as otherwise leg inju-
ries can result if the knee and front airbag is
triggered.
Never let an occupant's head rest near or
on a side airbag because the inflating air-
bag could cause a serious or fatal injury.<
Even if you adhere to all the instructions
injuries resulting from contact with airbags
cannot be fully excluded, depending on the
circumstances. The ignition and inflation
noise may provoke a mild Ð usually tempo-
rary Ð hearing loss in extremely sensitive
individuals.
For airbag locations and additional infor-
mation on airbags, refer to page 54.
Sitting safely with safety belts
Even though there is an airbag, wear a
safety belt every time you get in the vehi-
cle. Although airbags enhance safety by
providing added protection, they are not a
substitute for safety belts.
Your vehicle has five seats that are all
equipped with a safety belt.
Occupants should sit upright and be
properly restrained at all times:
infants and small children in appropriate
child-restraint systems; larger children and
adults using the safety belts.
Expectant mothers should always wear
their safety belts, taking care to position
the lap belt against the lower hips, where it
will not exert pressure against the abdomi-
nal area.
Never allow more than one person to wear
a single safety belt. Never allow infants and
small children to ride in a passengers lap.
Do not route the belt across your neck, or
run it across sharp edges. Be sure that the
belt does not become caught or jammed.
Avoid twisting the belt while routing it firmly
across the hips and shoulder. Do not allow
the belt to rest against hard or fragile
objects. Otherwise, in the event of a frontal
impact, a loose lap belt could slide over
your hips, leading to abdominal injury.
Avoid wearing clothing that prevents the
belt from fitting properly and pull the lap
belt periodically to readjust the tension
across your shoulder in order to avoid a
reduction in the retention effect of the
safety belt.<
For fastening safety belts, refer to page 30.
Seats
Note before adjusting
Never try to adjust your seat while
operating the vehicle. The seat could
respond with unexpected movement, and

Adjustments
30 3.Press MEMORY button:
The indicator lamp in the button lights
up
4.Press the desired memory button 1, 2
or 3:
The indicator lamp goes out.
Selecting a stored setting
Do not call up a position from the
memory while the vehicle is moving,
as otherwise there is a risk of accident from
unexpected seat movement.<
Convenience mode
1.Open the driver's door after unlocking
or turn the ignition key to position 1
2.Briefly press the desired memory but-
ton 1, 2 or 3.
The system immediately cancels the
adjustment procedure when you press
one of the seat adjustment buttons or
use one of the memory buttons.
Safety feature
1.Close the driver's door and turn the
ignition key to position 0 or 2
2.Press the desired memory button 1, 2
or 3 and maintain pressure until the
adjustment process has been com-
pleted.
If you press the
MEMORY button
accidentally:
Press the button a second time Ñ the indi-
cator lamp goes out.<
You can have your vehicle pro-
grammed to automatically dial in your
own individual adjustment settings for the
seat and exterior mirror position whenever
you use your personal remote control to
unlock the vehicle.<
If you make use of this adjustment, be
sure that the footwell behind the
driver's seat is unobstructed before
unlocking the vehicle. If you fail to do so,
any persons, animals or objects behind the
seat could be injured or damaged by a
rearward movement of the seat.<
Heated seats*
The seat cushion and backrest can be
heated when the ignition key is in
position 2.
To call up different temperature levels:
Press the button repeatedly.
To switch off from a higher heat setting:
Press the button and hold it slightly longer.
Safety belts
Even though there is an airbag, wear a
safety belt every time you get in the vehi-
cle. Although airbags enhance safety by
providing added protection, they are not a
substitute for safety belts.
Fastening
Make sure you hear the latch plate engage
in the belt buckle.
Please fasten safety belt warning
lamp:
Lights up for a few seconds or until
safety belts are fastened. Depending on
you vehicle version, a signal
* sounds
simultaneously.

Reference
At a glance
Controls
Driving tips
Mobility
33
Vehicle Memory,
Key Memory
How the system functions
You have probably frequently wished that
you could configure individual functions of
your vehicle to reflect your own personal
requirements. In developing your vehicle,
BMW has incorporated a number of
options for personal adjustment. You can
have these programmed at your BMW
Sports Activity Vehicle Center.
There are vehicle-related and person-
related adjustments: Vehicle Memory and
Key Memory. You can configure up to four
different basic adjustments for four differ-
ent persons. The only requirement is that
each person uses his or her own master
key with remote control.
When your vehicle is unlocked with the
remote control, the vehicle recognizes the
individual user by means of a data
exchange with the key, and makes adjust-
ments accordingly.
In order for you to distinguish between the
remote control master keys, colored decals
are supplied together with the keys.
What the system can do
Your BMW Sports Activity Vehicle Center
can provide you with details on the capabil-
ities of the Vehicle Memory and Key Mem-
ory systems.
You will see this symbol throughout
the Owner's Manual. It is to remind
you at appropriate places of the settings
that are available to you.<
Examples of Vehicle Memory
functions
>Different acknowledgment signals to
confirm locking/unlocking of the vehi-
cle, refer to page 18
>Activate/deactivate function for path-
way lighting, refer to page 57
>Activate/deactivate daytime driving
lamps, refer to page 57
>Setting measurement units for displays
in the instrument cluster of the time,
outside temperature, distance driven
and fuel consumption, refer to page 47
>Active PDC is indicated by an acoustic
sound signal when reverse gear or
selector-lever position R is engaged,
refer to page 49
>The rear window defroster switches on
automatically, refer to page 61
>Different acknowledgment signals to
confirm arming/disarming the alarm
system, refer to page 25
>After an ice warning has been issued,
the display of the computer returns to
the previous adjustment, refer to
page 47
>Acoustic warning if the ignition key
remains in the ignition lock after the
driver's door has been opened, refer to
page 21.
Examples of Key Memory functions
>On unlocking, first unlock the driver's
door, then the entire vehicle, refer to
page 19
>Locking the vehicle after moving off,
refer to page 20
>Automatic adjustment of the driver's
seat and exterior mirror position for
each person when unlocking the vehi-
cle, refer to page 30
>Angle of downward tilt of mirror on pas-
senger side, refer to page 32.

Reference
At a glance
Controls
Driving tips
Mobility
35
Installing child-restraint
systems
Before installing any child-restraint system
or child seat, read the following:
Observe the child-restraint system
manufacturer's instructions for instal-
lation and use. Otherwise the degree of
protection can be reduced.
After an accident, have all parts of the rele-
vant vehicle safety belt system checked by
a BMW Sports Activity Vehicle Center and
replaced if necessary.<
Commercially-available child-restraint sys-
tems are designed to be secured with a lap
belt or with the lap belt portion of a combi-
nation lap/shoulder belt. Improperly or
inadequately installed restraint systems
can increase the risk of injury to children.
Always read and follow the instructions that
come with the system.
Child seat security
All of the rear belt retractors and the front
passenger's safety belt can be locked for
mounting and securing child-restraint sys-
tems.
Information regarding this is located near
the buckle latch of each safety belt.
To lock the safety belt
Pull the entire length of the belt from the
belt retractor. Allow the reel to retract the
belt somewhat and engage the buckle,
then tighten the belt against the child-
restraint system. The retraction mechanism
is now locked.
To unlock the safety belt
Release the buckle, remove the child-
restraint system and allow the belt retractor
to reel the belt completely in.
Child-restraint system with tether
strap
If you use a child-restraint system with a
tether strap, three additional tether anchor-
age points have been provided, refer to the
arrows in the illustration. Depending on the
location selected for seating in the rear
passenger area, attach the tether strap to
the corresponding anchorage point to
secure the child-restraint system, as
shown in the illustration below.
Each seating position is fitted with a head
restraint.
Outer seating positions:
Lift the head restraint and pass the tether
strap between the head restraint and the
seat back. It is recommended to readjust
the head restraint into the lowest possible
position.
Center seating position:
The head restraint must be adjusted into
the lowest possible position. Pass the
tether strap over the head restraint.

Transporting children safely
36 Adjust the tether strap according to
the child-restraint manufacturer's
instructions.<
LATCH* child-restraint fixing
LATCH: Lower Anchor and Tethers for
CHildren.
The rear outer seating positions are pro-
vided with anchors for a LATCH child-
restraint fixing.
Access to anchorage points
The illustrations show the left rear seat as
an example. The anchorage points for the
LATCH child seat fixing are located behind
the cover caps.
Remove the cover caps toward the front.
Press on to remount.
Canadian models only:
The anchorage points for the LATCH child-
restraint fixing are identified by buttons.
To fit the child seat fixing LATCH, fol-
low the operating and safety instruc-
tions of the manufacturer.<
Before mounting the LATCH child-restraint
fixing, remove the cover caps.1.Engage the center safety belt into the
belt buckle
2.Pull the belt away from the area of the
child seat fixing.
For driving
With side airbags in the rear, make
sure that children do not lean out of
the child's seat toward the door panel, as
otherwise major injuries can result if the
side airbags are triggered.<
You can have the rear side airbags perma-
nently deactivated.
Your BMW Sports Activity Vehicle Center
will be happy to advise you.
Child-safety lock of rear doors
Slide down the safety levers on the rear
doors:
The door can now be opened from the out-
side only.
Safety switch for power windows
Always press the safety switch for the elec-
tric power windows, refer to page 22, when
children are in the rear of the vehicle.

Reference
At a glance
Controls
Driving tips
Mobility
37
Driving
Ignition lock
0 Steering locked
The key can only be inserted or removed in
this position.
After removing the key, turn the steering
wheel slightly to the left or right until you
hear the lock engage.
Vehicles with automatic transmission:
Only move the selector lever from
position P with the engine running. To turn
the key back to position 0 or to remove it,
first place the selector lever in position P:
Interlock.<
1 Steering unlocked
A slight steering wheel movement often
makes it easier to turn the key from 0 to 1.
Individual current consumers are ready for
operation.
2 Ignition switched on
All vehicle systems are ready for operation.
3 Engine start
Engine
Do not allow the engine to warm up while
idling. Drive off immediately at moderate
engine speed.
Engine idle speed is controlled by the
engine computer system. Increased
speeds at startup are normal and should decrease as the engine warms up. If engine
speed does not decrease, service is
required.
To prevent the battery from discharging,
always switch off electrical devices which
are not in use and the ignition when the
vehicle is not being driven.
Do not run the engine in closed
rooms, as otherwise inhaling toxic
exhaust gases can cause unconsciousness
and death. The exhaust gases contain car-
bon monoxide, an odorless and colorless,
but highly toxic gas. Do not leave the vehi-
cle unattended with the engine running,
since an unattended vehicle with a running
engine represents a safety hazard.
When driving, standing at idle and while
parking take care to avoid possible contact
between a hot exhaust system and any
highly flammable materials such as hay,
leaves, grass, etc. Such contact could lead
to a fire, resulting in serious personal injury
and property damage.<
Indicator lamps
If the Service Engine Soon indicator
lamp comes on either continuously
or intermittently, this indicates a
fault in the emissions-related electronic
systems. Although the vehicle remains
operational, you should have the systems
checked by your BMW Sports Activity
Vehicle Center at the earliest possible
opportunity.
The illuminated indicator informs you of the
need for service, not that you need to stop
the vehicle. However, the systems should
be checked by your BMW Sports Activity
Vehicle Center at the next opportunity.
If the indicator blinks or flashes, this indi-
cates a high level of engine misfire. Reduce
speed and contact the nearest BMW
Sports Activity Vehicle Center immediately.
Severe engine misfiring over even a short
period of time can seriously damage emis-

Driving
38 sion control system components, espe-
cially the catalytic converter.
Service Engine Soon indicator lamp
for Canadian models.
Malfunction in the engine electron-
ics.
You can continue to drive with
reduced engine output or engine speed.
Please have it checked by your BMW
Sports Activity Vehicle Center.
Starting the engine
When starting the engine, do not press the
accelerator pedal.
Vehicles with manual transmission:
Step on the clutch when starting the
vehicle. A lockout prevents the engine from
starting if the clutch is not depressed.<
Do not actuate the starter for too
short a time. Do not turn it for more
than approx. 20 seconds. Release the igni-
tion key immediately as soon as the engine
starts.<
If the engine fails to start on the first
attempt, for instance, if it is very hot or cold:
>Press the accelerator pedal halfway
down while engaging the starter.
During a cold start at very low tempera-
tures, as of approx. +57/Ð156, at high
altitudes over 3,300 ft/1,000 m:
>For the first attempt, run the start for
longer, approx. 10 seconds
>Press the accelerator pedal halfway
down while engaging the starter.
Avoid frequent starting is quick suc-
cession or repeated start attempts in
which the engine does not start. Otherwise,
the fuel is not burned or inadequately
burned and there is a danger of overheat-
ing and damaging the catalytic converter.<
Manual transmission
1.Engage the handbrake
2.Gearshift lever in idle position
3.Press the clutch pedal
4.Start the engine.Before leaving the vehicle with the
engine running, place the gearshift
lever in idle position and apply the hand-
brake.
Never leave an unattended vehicle with the
engine running, as such a vehicle repre-
sents a potential safety hazard.<
Automatic transmission
1.Press the brake pedal
2.Place the selector lever in position P
or N
3.Start the engine.
To prevent the vehicle from rolling,
always select position P and engage
the handbrake before leaving the vehicle
with the engine running.
Never leave an unattended vehicle with the
engine running, as such a vehicle repre-
sents a potential safety hazard.<
Switching off the engine
Do not remove the ignition key when
the vehicle is moving, as otherwise
the steering could lock.
When leaving the vehicle, always remove
the ignition key and lock the steering.
When parking on downward inclines, apply
the handbrake.<
Manual transmission
Turn the ignition key to position 1 or 0.
Automatic transmission
Engage selector-lever position P, turn igni-
tion key to position 1 or 0.
Handbrake
The handbrake is primarily intended to pre-
vent the vehicle from rolling while parked; it
brakes the rear wheels.
Indicator lamp
The indicator lamp lights up from
ignition switch position 2 with the
handbrake set Ð an acoustic signal
also sounds when starting off.

Driving
40
Selector lever positions
P R N D M/S + Ð
Engine started
The engine can only be started in selector-
lever positions P Ð Park Ð or N Ð Neutral.
Range selection
An interlock prevents inadvertent gear-
shifts into selector-lever positions R and P.
To cancel the interlock, press the button on
the front of the selector-lever knob.
Shiftlock
Press the brake pedal before shifting
out of P or N; the shift command will
not be executed unless the brake is applied
Ð Shiftlock.<
To prevent the vehicle from 'creeping'
after you select a range, maintain
pressure on the brake pedal until you are
ready to start. If you leave the vehicle with
the engine running, engage selector-lever
position P and apply the handbrake. If you
fail to do this, the vehicle could move.
Never leave an unattended vehicle with
the engine running, as such a vehicle rep-
resents a potential safety hazard.<
P Park
Select only when the vehicle is stationary.
The transmission locks to prevent the rear
wheels from turning.
R Ñ Reverse
Select only when the vehicle is stationary.
N Ð Neutral
Select only if your journey is interrupted for
a longer period.
D Drive Ð Automatic shift program
This position is designed for driving under
all normal operating conditions. All forward
gears are available.
Kickdown
A kickdown provides you with maximum
acceleration and the maximum road speed
in position D.
Press the accelerator pedal past the
increased resistance point at the full-
throttle position.
M/S Manual mode and
Sport Program
Shifting from D into M/S activates the Sport
program and this is indicated with SD in the
gear display. The Sport Program is
designed for performance-oriented driving.
The first time the selector lever is even
slightly touched, the automatic transmis-
sion shifts from the Sport program into
manual operation.
If you start to move the selector lever
towards
+, the transmission shifts
upwards; moving it towards
Ð shifts down-
wards. The gear display shows M1 through
M5.
Upshifts and downshifts are executed only
when they will result in a plausible combi-
nation of engine and vehicle speed; thus,
for example, a downshift that would cause
the engine to overrev will not be executed
by the system. The gear selected will