2004 BMW 545i vanos solenoid

Downloaded from www.Manualslib.com manuals search engine 5
N62 Engine
Engine Views
1
2
3
45
6
7
42-02-03 N62B44 Engine (Front View)
1. Starter Motor
2. Valvetronic Motor
3. Evaporative Emission Valve
4. VANOS Solenoid Valve
5. Thermostat Housing
6. Throttle Unit
7. Vacuum Pump
N62B44 Engine (Rear View)
1. Camshaft Position Sensor
Cylinder Bank 5-8
2. Valvetronic Eccentric Shaft
Position Sensor, Cylinder
Bank 5-8
3. Valvetronic Eccentric Shaft
Position Sensor, Cylinder
Bank 1-4
4. Camshaft Position Sensor
Cylinder Bank 1-4
5. Secondary Air Non-return Valves
6. Servomotor for Variable Intake
Manifold
42-02-04

Downloaded from www.Manualslib.com manuals search engine Cylinder Heads
The two N62 cylinder heads are a new development from BMW. They are fitted with the
Valvetronic system. The secondary air ducts for subsequent exhaust gas treatment are
integrated in the cylinder heads. The cylinder heads are cooled by the “cross-flow” princi-
ple.
The inlet camshaft and the Valvetronic eccentric shaft are jointly guided by a bridge sup-
port. The cylinder heads are made from aluminum and are manufactured using gravity die-
casting. The upper timing chain housing is now an integral part of the cylinder head.
20
N62 Engine
Cylinder Head
1. Cylinder Head for Cylinder Bank 1-4 7. Mounting VANOS Intake Solenoid
2. Cylinder Head for Cylinder Bank 5-8 8. Mounting VANOS Outlet Solenoid
3. Upper Timing Chain Guide with Oil Jet 9. Oil Pressure Switch
4. Mounting for VANOS Intake Solenoid 10. Chain Tensioner Mount
5. Mounting for VANOS Outlet Solenoid 11. Upper Timing Chain Guide with Oil Jet
6. Chain Tensioner Mount43-02-20

Downloaded from www.Manualslib.com manuals search engine 30
N62 Engine
Camshaft Sensors
The cam shaft sensors (Hall effect) are mounted through the cylinder head cover. There are
two sensors per cylinder head to monitor the intake and exhaust camshaft positions.
The sensors monitor the impulse wheels
attached to the ends of the camshafts.
Solenoid Valves
The VANOS solenoid valves are mounted through the upper timing case front cover. There
are two solenoids per cylinder head to control the oil flow to the camshaft ports for the
intake and exhaust VANOS units.
The 4/3 way proportional solenoid valve is acti-
vated by the ECM to direct oil flow. The sole-
noid valve is sealed to the front cover by a radi-
al seal and secured by a retaining plate.
N No
ot
te
es
s:
:

42-02-48 Camshaft Sensors
1. Valvetronic Position Sensor
2. Intake Camshaft Position Sensor
3. Exhaust Camshaft Position Sensor
42-02-42

Downloaded from www.Manualslib.com manuals search engine 31
N62 Engine
VANOS Sectional Views
M Me
ec
ch
ha
an
ni
ic
ca
al
l
L
La
ay
yo
ou
ut
t:
:
The figures above show a sectional view of one VANOS unit. The VANOS unit is secured
by a central bolt through the hub (7) to the camshaft. The timing chain connects the crank-
shaft with the housing of the unit.
There is a recess in the hub in which the locking pin (6) engages without oil pressure
(sprung). When the solenoid valve is activated to supply oil pressure to the VANOS unit,
the locking pin is compressed and releases the VANOS for adjustment.
The internal blades (9) are spring loaded (10) to provide a seal between the oil pressure
chambers (11 and 12). The torsion spring (3) acts against the camshaft torque.
42-02-4942-02-45
VANO’S Components
1. Housing with Sprocket 7. Hub
2. Front Plate 8. Black Plate
3. Torsion Plate 9. Blade
4. Lock Spring 10. Spring
5. Retaining Plate for Lock Spring 11. Pressure Chamber A
6. Spring Loaded Locking Pin 12. Pressure Chamber B

Downloaded from www.Manualslib.com manuals search engine 32
N62 Engine
H Hy
yd
dr
ra
au
ul
li
ic
c
A
Ac
ct
tu
ua
at
ti
io
on
n:
:
When oil pressure is applied to chamber A, the blades are forced away from the VANOS
housing (counterclockwise). The blades are keyed into the hub which results in the hub
position being rotated in relation to the housing (with sprocket). The hub is secured to the
camshaft which changes the camshaft to sprocket relationship (timing).
The example below shows the a ad
dj
ju
us
st
tm
me
en
nt
t
procedure together with the pressure progres-
sion based on the VANOS unit for the exhaust camshafts.
During this adjustment chamber B is open (through the solenoid) to allow the oil to drain
back through the cylinder head (internal reservoir).
Hydraulic Actuation - Chamber A
1. Front View of Vanos Unit 5. Engine Oil Pump
2. Side View of Vanos Unit 6. Supplied Oil from Pump (Switched Through Solenoid)
3. Camshaft Oil Port (Chamber B) 7. Supplied Oil Pressure (From Engine Oil Pump)
4. Solenoid Valve43-02-45

Downloaded from www.Manualslib.com manuals search engine 33
N62 Engine
When the solenoid valve switches over, oil pressure is applied to chamber B. This forces
the blades (and hub) in a clockwise direction back to the initial position, again changing the
camshaft timing.
The example below shows the r re
es
se
et
t
procedure together with the pressure progression
based on the VANOS unit for the exhaust camshafts.
During this adjustment chamber A is open (through the solenoid) to allow the oil to drain
back through the cylinder head (internal reservoir).
N No
ot
te
es
s:
:

42-02-44 Hydraulic Actuation - Chamber B
1. Front View of VANOS Unit 5. Engine Oil Pump
2. Side View of VANOS Unit 6. Oil Return (Switched through Solenoid)
3. Camshaft Oil Port (Chamber B) 7. Supplied Oil Pressure (From Engine Oil Pump)
4. Solenoid Valve

Downloaded from www.Manualslib.com manuals search engine 35
N62 Engine
Chain Drive
The camshafts are driven by a toothed chain, one for each cylinder bank. The oil pump is
driven by a separate roller chain.
1. Sensor wheels for the camshaft position sensor, cylinder bank 1-4
2. Tensioner Rail, Cylinder 5-8
3. Chain Tensioner, Cylinder Bank 5-8
4. Sensor Wheel for the camshaft position sensor, cylinder bank 5-8
5. Upper timing chain guide with integrated oil jet
6. Guide rail
7. Sprocket for Oil Pump Drive
8. Timing case lower section
9. Tensioning rail, cylinder bank 1-4
10. Solenoid Valve, VANOS exhaust camshaft
11. Solenoid Valve, VANOS intake camshaft
12. Upper Timing Chain Cover
13. Chain Tensioner, Cylinder Bank 1-4
14. VANOS exhaust camshaft Bank 1-4
15. Upper Timing Chain guide with integrated oil jet
16. VANOS intake camshaft 1-4Chain Drive
43-02-50