2004 Acura TSX buttons

To adjust the height of a f ront seat
belt anchor, squeeze the two release
buttons and slide the anchor up or
down as needed (it has f our
positions).See page f or additional
inf ormation about your seat belt
system and how to take care of your
belts.
This could cause
very serious injuries in a crash.
If a seat belt does not seem to work
as it should, it may not protect the
occupant in a crash.
Anyone using a seat belt that is
not working properly can be
seriously injured or killed. Have your
Acura dealer check the belt as soon
as possible. 43
Protecting Adults
Driver and Passenger Saf ety
Never place t he shoulder port ion of a
lap/shoulder belt under your arm orbehind your back.
No one should
sit in a seat wit h an inoperat ive seat belt.
17
RELEASE BUTTONS

Your Acura’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.
The in-dash CD changer holds up to
six discs. You operate the CD
changer with the same controls used
f or the radio. See page f or CD
changer operation.
The anti-thef t f eature will disable the
system if it is disconnected f rom the
car’s battery. To get the system
working again, you must enter a
code number (see page ).172
136
A M/FM/CD Changer
Audio System
Without Navigation System
Audio System
Comf ort and Convenience Feat ures129
AM/FM BUTTON
TUNE KNOB
PRESET BUTTONS STEREO INDICATOR
SEEK
BAR
SCAN
BUTTON
PWR/VOL KNOB A. SEL INDICATOR
A. SEL
BUTTON

µ
µ
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button. On the FM band, ST will be
displayed if the station is broadcast-
ing in stereo. Stereo reproduction on
AM is not available. The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
the SEEK bar ( or ), then
release it. Depending on which side
of the SEEK bar you press, the
system scans upward or downward
f rom the current f requency. It stops
when it finds a station with a strong
signal.
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, AUTO
SELECT, and the preset buttons. The ignition switch must be in the
ACCESSORY (I) or ON (II) position
to operate the audio system. Turn
the system on by pressing the PWR/
VOL knob or the AM or FM button.
Adjust the volume by turning the
knob. Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Operating the Radio
SEEK
TUNE
Audio System
Comf ort and Convenience Feat ures130

µ
µ
To store a f requency:UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station. You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
Pick the preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM. Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
The preset f requencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio f use is
removed.
The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan up
the band for a station with a strong
signal. When it f inds one, it will stop
and play that station for about 5
seconds. If you do nothing, the
system will then scan f or the next
strong station and play that for 5
seconds. When it plays a station that
you want to continue listening to,
press the SCAN button again. 1.
2.
3.
4. Preset
SCAN
Audio System
Comf ort and Convenience Feat ures131

µIf you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
To activate Auto Select, press the
A. SEL button. A. SEL will f lash in
the display, and the system will go
into scan mode f or several seconds.
It automatically scans both bands,
looking f or stations with strong
signals. It stores the f requencies of
six AM stations and twelve FM
stations in the preset buttons. You
can then use the preset buttons to
select those stations.
If you are in a remote area, Auto
Select may not f ind six strong AM
stations or twelve strong FM stations.
If this happens, you will see a ‘‘0’’
displayed when you press any preset
button that does not have a station
stored. AUTO SELECT
Audio System
Comf ort and Convenience Feat ures132
AM/FM BUTTON A. SEL INDICATOR A. SEL BUTTON
SEEK
BAR
SCAN
BUTTON
PRESET BUTTONS

If you do not like the stations Auto
Select has stored, you can store
other f requencies in the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind the desired
f requencies, then store them in the
selected preset buttons as described
previously.
Auto Select does not erase the
f requencies that you set previously.
When you return home, turn of f
Auto Select by pressing the A. SEL
button. The preset buttons will then
select the f requencies you originally
set.
Audio System
Comf ort and Convenience Feat ures133
A. SEL
BUTTON
SCAN
BUTTON AM/FM BUTTON
PRESET BUTTONSA. SEL INDICATOR
SEEK
BAR

If you press the LOAD button while
a CD is playing, the system will stop
playing that CD and start the loading
sequence. It will then play the CD
just loaded.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. Select an empty position (the
disc number indicator is of f ), and
press the preset button f or that
position (1 to 6). The system will
stop playing the current CD and start
the loading sequence. It will then
play the CD just loaded.
Audio System
Comf ort and Convenience Feat ures138
SCAN INDICATORRPT BUTTON
SKIP BAR
RDM
BUTTON
SCAN
BUTTON
LOAD BUTTON
PWR/VOL KNOB RPT INDICATOR
RDM INDICATOR
AM/FM BUTTON
PRESET BUTTONS
CD
BUTTON

Î
Î
The cassette system f eatures Dolby
noise reduction, automatic sensing of
chromium-dioxide (CrO ) tape, and
auto-reverse f or continuous play.
To operate the cassette player, the
ignition switch must be in the
ACCESSORY(I) or ON(II) position.
Make sure the tape opening on the
cassette is facing to the right, then
insert the cassette most of the way
into the slot. The system will pull it
in the rest of the way, and begin to
play.
2
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
Operating the Cassette Player
(Optional)
Audio System
Comf ort and Convenience Feat ures144
CD/AUX
BUTTON TAPE DIRECTION INDICATOR
RPT INDICATOR RPT BUTTON
PWR/VOL KNOB PRESET BUTTONS
AM/FM BUTTON
SEEK/SKIP
BAR