2004 Acura TL ignition

To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display.
When you remove the disc f rom the
slot, the system automatically begins
the load sequence so you can load
another disc in that position. If you
do not load another disc, within 15
seconds, the system selects the
previous mode [AM, FM1, FM2,
tape, or Satellite Radio (U.S.
models)].
If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 15 seconds and put the
disc changer in pause mode. To
begin playing the disc, press the disc
button.To remove a dif f erent disc f rom the
changer,firstselectitbypressing
the corresponding number on the
preset button (touching the
appropriate disc icon on models with
navigation system). When that disc
begins playing, press the eject button.
When you press the eject button
while listening to the radio, or with
the audio system turned of f , the disc
that was last selected is ejected.
Af ter that disc is ejected, pressing
the eject button again will eject the
next disc in numerical order. By
doing this six times, you can remove
all the discs f rom the changer.
You can also eject discs when the
ignition switch is of f :
To eject one disc, press and release
the eject button.
To eject all discs, press and hold the
eject button until the system beeps.
Playing Discs
Removing Discs f rom the
Changer
Comf ort and Convenience Feat ures133

Ûµ
Î
Î
CONT INUED
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Make sure the open side of the tape
is facing right, then insert the tape
most of the way into the slot. The
system will pull the tape in the rest
of the way, and begin to play it.
Thetapedirectionindicatorinthe
display comes on to show you which
side of the tape is playing. The
indicates the side you inserted
upward is now playing. If you want to
play the other side, press the PLAY/
PROG (preset2) button or touch the
PLAY/PROGiconontheaudio
display (models with navigation
system). When the player reaches
the end of the tape, it will
automatically reverse direction and
play the other side.
Dolby noise reduction turns on
when you insert a tape. Theindicator and NR icon (models with navigation system) will come on
in the display. If the tape was not
recorded in Dolby, turn it of f by
pressing the (preset 4) button
or touching the NR icon on the audio
display. Dolby remains of f until you
press the button (touch the icon)
again.
To remove the tape, press the
EJECT button. If you want to turn
the player of f , press the VOL/PWR
knob or turn of f the ignition. The
tape will remain in the drive. When
youturnthesystembackon,the
tape will begin playing where it lef t
off.
To switch to the radio, Satellite Radio (U.S. models) or disc changer
while a tape is playing, press the
AM/FM button (AM or FM button
on Canadian models), button
or DISC/TAPE button (CD/DVD
buttononCanadianmodels).To
change back to the tape player, press
the DISC/TAPE button (TAPE/
AUXbuttononCanadianmodels).
To rewind the tape,
push the (preset 1 ) button or
touch the REW icon on the audio
display (models with navigation
system). You will see REW in the
display (TAPE REW on models with
navigation system). To fast forward
the tape, push the (preset 3)
button or touch the FF icon. You will
seeFFdisplayed(TAPEFFon
models with navigation system).
Press the , , or PLAY/
PROG button (icon) to take the
system out of rewind or f ast f orward.
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
Playing a T ape
Comf ort and Convenience Feat ures
To Play a Tape
To Stop Playing a TapeFF/REW T ape Search Function
137

The HFL will accept a numeric, f our-
digit passcode that you can use f or
security purposes.Press and release the Talk button.
Af ter the beep, say ‘‘Set passcode.’’ With the ignition in the ON (II)
position, press and release the
Talk button on the steering wheel.
Af ter the beep, say ‘‘Security.’’ The
HFL response is ‘‘Security options
are lock, unlock, and set passcode.’’
The HFL response is ‘‘What is the
new f our-digit passcode?’’ (If you
are changing the passcode, you
will f irst be asked f or the current
passcode.) Press and release the Talk button.
Af ter the beep, say the f our-digit
passcode you want to use. For
example,say‘‘1,2,3,4.’’TheHFL
responseis‘‘1,2,3,4.Isthis
correct?’’
Press and release the Talk button.
Af ter the beep, say ‘‘Lock’’ or
‘‘Unlock.’’ means the HFL
will prompt you f or your passcode
each time the ignition switch is
turned to ON (II) and you press
the Talk button. You will only be
askedforthepasscodeonceper
ignition cycle. If the HFL is locked,
its response is ‘‘System is locked.
Each time the vehicle is turned on,
the passcode will be required to
use the system.’’ If the HFL is
unlocked, its response is ‘‘The
system is unlocked. Returning to
the main menu.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Yes.’’ The
HFL response is ‘‘The new
passcode has been stored.
Returning to the main menu.’’
Once a passcode is set, you can lock
the HFL so it only operates after the
passcode is entered, or you can
unlock it so anyone using your
vehicle can also use the HFL. Press and release the Talk button.
Af ter the beep, say ‘‘Security.’’ The
HFL response is ‘‘Security options
are lock, unlock, and set passcode.’’
2. 1.
4.
5.
3. 1.2.
To set your passcode, do this:
To lock or unlock the HFL, do this:
HandsFreeL ink
Comf ort and Convenience Feat ures
Setting Your Passcode Lock
L ocking or Unlocking the HFL
153
TM

With your phone on and the
ignition in the ACCESSORY (I) or
ON (II) position, press and release
the Talk button. After the beep,
say ‘‘Phone set up.’’ The HFL
response is ‘‘Phone set up options
are status, pair, edit, delete, and
list.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Pair.’’ The
HFL response is ‘‘The pairing
process requires operation of your
mobile phone. For saf ety, only
perf orm this f unction while the
vehicle is stopped. State a f our-
digit code f or pairing. Note this
code. It will be requested by the
phone.’’
Press and release the Talk button.
Af ter the beep, say the f our-digit
code you want to use. For example,
say‘‘1,2,3,4.’’TheHFLresponse
is,‘‘1,2,3,4.Isthiscorrect?’’Press and release the Talk button.
Af ter the beep, say ‘‘Enter’’. The
HFL response is ‘‘Searching f or a
Bluetooth phone.’’
Steps 5 and 6 show a
common way to get your phone into
its Discovery mode. If these steps do
not work on your phone, ref er to the
phone’s operating manual.
Follow the prompts on your phone
to get it into its Search mode. The
phone will search f or the HFL.
When it comes up, select
HandsFreeLink f rom the list of
options displayed on your phone.
When asked by the phone, enter
the four-digit code from step 3 into
your phone. The HFL response is
‘‘A new phone has been f ound.
What would you like to name this
phone?’’ Press and release the Talk button.
After the beep, say the name you
want to use. For example, say
‘‘Eric’s phone.’’ The HFL response
is ‘‘Eric’s phone has been
successf ully paired. Returning to
the main menu.’’
If you want to pair another phone,
repeat steps 1 through 7.
1.
4.
5.
6.7.
2.
3. 8.
CONT INUED
HandsFreeL ink
Comf ort and Convenience Feat ures155
NOTE:
TM

Press and release the Talk button.
Af ter the beep, say ‘‘Call’’ or ‘‘Dial.’’
The HFL response is ‘‘Calling’’ or
‘‘Dialing.’’ Once connected, you
will hear the person you called
through the audio speakers. To
change the volume, use the audio
system volume knob.
You can make calls using any phone
number, or by using a name in the
HFL phonebook. You can also redial
the last number called. During a call,
theHFLallowsyoutotalkupto30
minutes af ter you remove the key
from the ignition switch.
With your phone on and the
ignition in the ACCESSORY (I) or
ON (II) position, press and release
the Talk button. After the beep,
say ‘‘Call’’ or ‘‘Dial’.’ The HFL
response is, ‘‘What name or
number would you like to call/
dial?’’
Press and release the Talk button.
Af ter the beep, say the number
you want to call. For example, say
‘‘123 456 7891.’’ The HFL response
is ‘‘123 456 7891. Say call, dial, or
continue to add numbers.’’ To end the call, press the Back
button.
With your phone on and the
ignition in the ACCESSORY (I) or
ON (II) position, press and release
the Talk button. After the beep,
say ‘‘Call’’ or ‘‘Dial.’’ The HFL
response is ‘‘What name or
number would you like to call/
dial?’’
Press and release the Talk button.
After the beep, say the name you
want to call. For example, say‘‘Eric.’’ The HFL response is
‘‘Would you like to call Eric?’’
Press and release the Talk button.
Af ter the beep, say ‘‘Yes.’’ The
HFL response is ‘‘Calling’’ or
‘‘Dialing.’’ Once connected, you
will hear the person you called
through the audio speakers. To
change the volume, use the audio
system volume knob.
To end the call, press the Back
button.
To redial the last number called by
the phone, press and release the
Talk button. After the beep, say
‘‘Redial.’’ The HFL response is,
‘‘Redialing.’’ Once connected, you
will hear the person you called
through the audio speakers. To
change the volume, use the audio
system volume knob.
1. 3.
3.
1.
2. 2. 4.4.
To make a call using a phone number,do this:
To make a call using a name in the HFLphonebook, do this:
Making a Call
HandsFreeL ink
Comf ort and Convenience Feat ures158
TM

Apply the parking brake.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.
Push the clutch pedal down all the
way.
Make sure the shif t lever is in
Park. Press on the brake pedal.
Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. Do not hold
the key in START for more than
15 seconds at a time. If the engine
does not start right away, pause
f or at least 10 seconds bef ore
trying again.If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed halfway
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.
If the engine fails to start, press
the accelerator pedal all the way
downandholdittherewhile
starting to clear flooding. If the
engine still does not start, return
to step 5.
1.
2.
3.
4. 5.
6.
Manual Transmission:
Automatic Transmission:
Driving
Starting the Engine
177
NOTICE: The engine is harder to start
in cold weather. Also, the thinner air
f ound at altitudes above 8,000 f eet
(2,400 meters) adds to this problem.

The 6-speed manual transmission
has an electric lockout so you cannot
accidentally shif t f rom Fif th to
Reverse instead of Sixth. If you
cannot shif t to Reverse when the
vehicle is stopped:With the clutch pedal pressed,
move the shift lever to the first/
second gear side of the Neutral
gate, then shif t to Reverse.If you are still unable to shif t to
Reverse, apply the parking brake
and turn the ignition key to
ACCESSORY (I) or LOCK (0).
Press the clutch pedal, and shif t to
Reverse.
With the clutch pedal still pressed,
start the engine.
If you need to use this procedure to
shif t to Reverse, your vehicle may be
developing a problem. Have the
vehicle checked by your Acura
dealer.
1. 2.
3.
4.
Driving
6-speed Manual T ransmission
Reverse Lockout
180

These indicators on the instrument
panel show which position the shif t
lever is in. The illuminated number
next to the ‘‘L’’ indicator shows you
the gear you have selected in the
Sequential SportShif t mode.The ‘‘D’’ indicator comes on f or a
f ew seconds when you turn the
ignition switch to ON (II). If it
f lashes while driving (in any shif t
position), it indicates a possible
problem in the transmission. Avoid
rapid acceleration and have the
transmission checked by an Acura
dealer as soon as possible.
To shif t f rom any position, press
f irmly on the brake pedal. You
cannot shif t out of Park when the
ignition switch is in the LOCK (0) or
ACCESSORY (I) position.
CONT INUED
Shif t L ever Position Indicators Shif ting
Automatic Transmission
Driving181