Page 64 of 370

If a brake light does not work, theindicator comes on
when you push the brake pedal with
the ignition switch ON (II).
A burned out brake light is a hazard
when drivers behind you cannot tell
you are braking. Have your brake
lights repaired right away. The lef t or right turn signal light
blinks when you signal a lane change
or turn. If the light does not blink or
blinks rapidly, it usually means one
of the turn signal bulbs is burned out
(see page ). Replace the bulb as
soon as possible, since other drivers
cannot see that you are signaling.
WhenyouturnontheHazard
Warning switch, both turn signal
lights blink. All turn signals on the
outside of the vehicle should f lash.
The appropriate light comes on in
this display if the trunk or any door
is not closed tightly.
All the lights in the monitor display
come on f or a f ew seconds when you
turn the ignition switch to ON (II).
291
Indicator L ights
Inst rument s and Cont rols
Brake L amp Indicator
Turn Signal and
Hazard Warning
Indicators
Door and T runk Open Monitor
61
BRAKE LAMP
Page 242 of 370

If you have the skills and tools to per-
f orm more complex maintenance
tasks on your Acura, you may want
to purchase the Service Manual. See
page f or inf ormation on how to
obtain a copy, or see your Acura
dealer. This section also includes
Maintenance Schedules f or normal
driving and severe driving conditions,
a Maintenance Record, and instruc-
tions f or simple maintenance tasks
you may want to take care of
yourself . This section explains why it is
important to keep your car well
maintained and how to f ollow basic
maintenance saf ety precautions.......................
Maintenance Saf ety .240
.
Important Safety Precautions . 241
.................
Maintenance Schedule . 242
...
Required Maintenance Record . 249
.......
Owner Maintenance Checks . 251
..............................
Fluid Locations .252
......................................
Engine Oil .253
..................................
Adding Oil .253
....................
Recommended Oil .253
..............................
Synthetic Oil .254
....................................
Additives .254
.....
Changing the Oil and Filter . 255
.............................
Cooling System .257
............
Adding Engine Coolant . 257
.......
Replacing Engine Coolant . 259
....................
Windshield Washers .263
....
Automatic Transmission Fluid . 264
..............................
Dif f erential Oil .265
....................................
Brake Fluid .266
............................
Brake System .266
..............................
Power Steering .266
....................................
Hood Latch .267
.....................
Air Cleaner Element .267
....................................
Spark Plugs .269
..............................
Replacement .269
............................
Specif ications .272 ...........................................
Battery .272
.................................
Wiper Blades .275
..............
Air Conditioning System . 277
..................
Dust and Pollen Filter . 278
.....................................
Drive Belts .278
....................................
Timing Belt .279
...............................................
Tires .279
......................................
Inf lation .279
..................................
Inspection .281
..............................
Maintenance .282
.............................
Tire Rotation .282
...
Replacing Tires and Wheels . 283
......................
Wheels and Tires .284
..........................
Winter Driving .284
.............................
Snow Tires .285
............................
Tire Chains .285
.............................................
Lights .286
........................
Replacing Bulbs .288
...........................
Storing Your Car .297
355
Maintenance
Maint enance239
Page 289 of 370
Check the operation of your car’s
exterior lights at least once a month.
A burned out bulb can create an
unsaf e condition by reducing your
car’s visibility and the ability to
signal your intentions to other
drivers.
Lights
Maint enance286
HIGH BEAM HEADLIGHT LOW BEAM HEADLIGHT
FRONT FOG LIGHT TURN SIGNAL/ PARKING LIGHTSIDE MARKER LIGHT
Page 290 of 370
Check the f ollowing:Headlights (low and high beam)
Fog lights
Parking lights
Taillights
Brake lights
Turn signals
Back-up lights
Hazard light f unction
License plate lights
Side marker lights
High-mount brake light
Daytime running lights (Canadian
models)
If you f ind any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on page to
determine what type of replacement
bulb is needed. 339
Lights
Maint enance287
HIGH-MOUNT BRAKE LIGHT
TURN SIGNAL LIGHT
LICENSE PLATE
LIGHTS BACK-UP LIGHT BRAKE/TAILLIGHTS
Page 291 of 370

Halogen bulbs are used f or the high
beam headlight bulbs. When
replacing a high beam headlight bulb,
handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.Open the hood.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.
Theheadlightswereproperlyaimed
when your car was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustment of the
headlights should be perf ormed by
an Acura technician or other
qualif ied mechanic.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced. 1.
2.
3.
Lights
Maint enance
Headlight A iming
Replacing a High Beam Headlight
Bulb
288
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
Page 292 of 370
à
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb.
Insert the new bulb into the hole,
making sure the bulb is right side
up and the nubs on the bulb base
f it in the indentations in the
headlight assembly. Pivot the hold-
down wire back in place and clip
the end into the slot. Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘ .’’
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Your car uses halogen f og light
bulbs. See page f or inf ormation
on replacing a halogen bulb.
4.
5. 6.
7.
288
CONT INUED
Lights
Maint enance
ReplacingaFogLightBulb
289
WEATHER SEAL BULB
CONNECTOR HOLD-DOWN WIRE
Page 293 of 370
à
Put the light assembly into the
bumper. Tighten the mounting
bolt. Push the electrical connector onto
the new bulb. Turn on the f ront
f og lights to test the new bulb. Install the rubber seal over the
back of the f og light assembly.
Make sure it is right side up; it is
marked ‘‘ .’’
Use a wrench to loosen the light
assembly’s mounting bolt.
Remove the light assembly f rom
the bumper.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back. Remove the rubber weather seal
by pulling on the tab.
Unclip the end of the hold-down
wire f rom its slot. Pivot the wire
out of the way and remove the
bulb.Insert the new bulb into the hole,
making sure the bulb is right side
up and the nubs on the bulb base
f it in the indentations in the f og
light assembly. Pivot the hold-
down wire back in place and clip
the end into the slot.
1.
2.
3. 4.
5.6.
7.
8.
9.
Lights
Maint enance290
CONNECTOR
BOLT HOLD-DOWN WIRE
WEATHER SEAL
BULB
Page 294 of 370

To remove the f ront turn signal/
parking light bulb, push it in
slightly and turn it
counterclockwise. To remove the
side marker bulb, pull it straight
out of its socket.
Install the new bulb into the
socket.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise. Pull the inner f ender cover back.
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left. Put the inner f ender cover in place.
Install the holding clip. Lock it in
place by pushing on the center. Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
1. 2.
3.
4.5.
6.
7.
8.
9.
Lights
Maint enance
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
291
HOLDING CLIP