2003 YAMAHA YZF-R1 radiator cap

DESCRIPTION
2-2
2
Right view13. Luggage strap holders (page 3-23)
14. Helmet holders (page 3-18)
15. Main fuse (page 6-36)
16. Electronic fuel injection fuse (page 6-36)
17. Battery (page 6-34)
18. Rear brake fluid reservoir (page 6-28)19. Air filter element (page 6-18)
20. Radiator cap (page 6-15)
21. Coolant reservoir (page 6-13)
22. Engine oil level check window (page 6-9)
23. Engine oil filler cap (page 6-9)
U5PWE1.book Page 2 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
6
EC000080
CAUTION:_

If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.


If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the cool-
ing system will not be protected
against frost and corrosion.


If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.
_
EW000067
WARNING
_ Never attempt to remove the radia-
tor cap when the engine is hot. _NOTE:_

The radiator fan is automatically
switched on or off according to the
coolant temperature in the radia-
tor.


If the engine overheats, see page
6-47 for further instructions.
_
EAU04925
To change the coolant
1. Place the motorcycle on a level
surface and let the engine cool if
necessary.
2. Remove cowlings A and B, and
panel A. (See pages 6-5–6-7 for
cowling and panel removal and in-
stallation procedures.)
3. Place a container under the en-
gine to collect the used coolant.
U5PWE1.book Page 14 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-15
64. Remove the clutch cable holder
from the coolant reservoir as
shown.
5. Remove the coolant reservoir by
removing the bolts.
6. Remove the coolant reservoir cap,
and then turn the coolant reservoir
upside down to empty it.
7. Install the coolant reservoir by in-
stalling the bolts, and then install
the clutch cable holder.8. Remove the radiator cap.
EW000067
WARNING
_ Never attempt to remove the radia-
tor cap when the engine is hot. _
9. Remove the coolant drain bolt to
drain the cooling system.
10. Loosen the radiator hose clamp
screw located at the left side of the
engine, and then pull off the hose
to drain the radiator.
1. Bolt (× 2)
2. Radiator cap
3. Coolant reservoir cap
4. Coolant reservoir
5. Clutch cable holder
1. Coolant drain bolt
2. Clamp screw
U5PWE1.book Page 15 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-16
6 11. After the coolant is completely
drained, thoroughly flush the cool-
ing system with clean tap water.
12. Install the coolant drain bolt, and
then tighten it to the specified
torque.
NOTE:_ Check the washer for damage and re-
place it if necessary. _13. Connect the radiator hose, and
then tighten the clamp screw.14. Pour the specified amount of rec-
ommended coolant into the radia-
tor and reservoir.
EC000080
CAUTION:_

If coolant is not available, use
distilled water or soft tap water
instead. Do not use hard water
or salt water since it is harmful
to the engine.


If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the engine may not be
sufficiently cooled and the cool-
ing system will not be protected
against frost and corrosion.


If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness of
the coolant will be reduced.
_
Tightening torque:
Coolant drain bolt:
10 Nm (1.0 m·kgf)
Antifreeze/water mixture ratio:
1:1
Recommended antifreeze:
High-quality ethylene glycol
antifreeze containing corrosion
inhibitors for aluminum engines
Coolant quantity:
Total amount:
2.45 L
Coolant reservoir capacity
(up to the maximum level mark):
0.24 L
U5PWE1.book Page 16 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
615. Install the radiator cap and the
coolant reservoir cap, and then
start the engine and let it idle for
several minutes. During this peri-
od, rev the engine two or three
times between 3,000–5,000 r/min,
and then turn it off.
16. Remove the radiator cap to check
the coolant level in the radiator. If
necessary, add sufficient coolant
until it reaches the top of the radia-
tor, and then install the radiator
cap.
17. Check the coolant level in the res-
ervoir. If necessary, remove the
coolant reservoir cap, add coolant
to the maximum level mark, and
then install the cap.
18. Start the engine, and then check
the vehicle for coolant leakage. If
coolant is leaking, have a Yamaha
dealer check the cooling system.
19. Install the cowlings and the panel.
EAU04572*
Replacing the air filter
element The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.
1. Remove the rider seat. (See page
3-17 for rider seat removal and in-
stallation procedures.)
2. Remove the bolt.3. Lift the front of the fuel tank, and
then tilt it back and away from the
air filter case. (Do not disconnect
the fuel hoses!)
EW000071
WARNING
_

Make sure that the fuel tank is
well supported.


Do not tilt or pull the fuel tank
too much, otherwise the fuel
hoses may come loose, which
could cause fuel leakage.
_4. Disconnect the fuel tank breather
hose and the fuel tank overflow
hose.
1. Bolt
1. Fuel tank breather hose
2. Fuel tank overflow hose
U5PWE1.book Page 17 Monday, July 8, 2002 10:28 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-47
6Engine overheating
EW000070
WARNING
_

Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hiss-
ing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
_CT-2AENOTE:_ If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible. _
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See NOTE.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U5PWE1.book Page 47 Monday, July 8, 2002 10:28 AM

SPECIFICATIONS
8-4
8
Battery
Model GT12B-4
Voltage, capacity 12 V, 10 Ah
Headlight typeHalogen bulb
Bulb voltage, wattage × quantity
Headlight 12 V, 60/55 W × 2
Tail/brake light L.E.D.
Turn signal light 12 V, 10 W × 4
Auxiliary light 12 V, 5 W × 2
License plate light 12 V, 5 W × 1
Meter lighting L.E.D.
Neutral indicator light L.E.D.
High beam indicator light L.E.D.
Turn signal indicator light L.E.D.
Fuel level warning light L.E.D.
Oil level warning light L.E.D.
Engine trouble warning light L.E.D.
Engine speed indicator light L.E.D.
Fuses
Main fuse 50 A
Headlight fuse 20 A
Signaling system fuse 10 A
Radiator fan fuse 15 A
Ignition fuse 15 AOdometer and clock fuse
(backup fuse) 10 A
Electronic fuel injection fuse 15 A
Turn signal lights and
hazard fuse 10 A
U5PWE1.book Page 4 Monday, July 8, 2002 10:28 AM