2003 YAMAHA TZR50 torque

EAU17240
Safety is an obligation of the owner.
Periodic inspection, adjustment and
lubrication will keep your vehicle in
the safest and most efficient condi-
tion possible. The most important
points of inspection, adjustment, and
lubrication are explained on the follo-
wing pages.
The intervals given in the periodic
maintenance and lubrication chart
should be simply considered as a
general guide under normal riding
conditions. However, DEPENDING
ON THE WEATHER, TERRAIN, GEO-
GRAPHICAL LOCATION, AND INDIVI-
DUAL USE, THE MAINTENANCE
INTERVALS MAY NEED TO BE
SHORTENED.
EWA10320
s s
WARNING
If you are not familiar with mainte-
nance work, have a Yamaha dealer
do it for you.
EAU17380
Owner’s tool kit
1. Owner’s took kit
The owner’s tool kit is located under
the seat. (See page 3-7 for.)
The service information included in
this manual and the tools provided in
the owner’s tool kit are intended to
assist you in the performance of pre-
ventive maintenance and minor
repairs. However, additional tools
such as a torque wrench may be
necessary to perform certain mainte-
nance work correctly.
NOTE:
If you do not have the tools or expe-
rience required for a particular job,
have a Yamaha dealer perform it for
you.
EWA10350
s s
WARNING
Modifications not approved by
Yamaha may cause loss of perfor-
mance and render the vehicle
unsafe for use. Consult a Yamaha
dealer before attempting any chan-
ges.
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-1
1
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 33

EAU19620
Checking the spark plug
1. Spark plug
The spark plug is an important engine
component, which should be chec-
ked periodically, preferably by a
Yamaha dealer. Since heat and depo-
sits will cause any spark plug to
slowly erode, it should be removed
and checked in accordance with the
periodic maintenance and lubrication
chart. In addition, the condition of the
spark plug can reveal the condition of
the engine.
The porcelain insulator around the
center electrode of the spark plug
should be a medium-to-light tan (the
ideal color when the vehicle is riddennormally). If the spark plug shows a
distinctly different color, the engine
could be defective. Do not attempt to
diagnose such problems yourself.
Instead, have a Yamaha dealer check
the vehicle.
If the spark plug shows signs of elec-
trode erosion and excessive carbon
or other deposits, it should be repla-
ced.
Before installing a spark plug, the
spark plug gap should be measured
with a wire thickness gauge and, if
necessary, adjusted to specification.
Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
NOTE:
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4~1/2 turn past finger tight. Howe-
ver, the spark plug should be tighte-
ned to the specified torque as soon
as possible.
EAUM1270
Transmission oil
1. Oil level check bolt
2. Oil drain bolt
3. Oil filler cap
Tightening torque:
Spark plug:
20 Nm (2,0 m•kgf)
Spark plug gap:
0,6 ~ 0,7 mm (0,023~0,027 in)
Specified spark plug:
BR9ES (NGK)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-6
1
3
1
2
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 38

The transmission oil level should be
checked before each ride. In addition,
the oil must be changed at the inter-
vals specified in the periodic mainte-
nance and lubrication chart.
To check the transmission oil level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
2. Remove the oil check bolt, and
then check the oil level.
NOTE:
The oil should be at the brim of the
check hole.
3. If the oil is below the brim of the
check hole, remove the oil filler
cap, add sufficient oil of the
recommended type to raise it to
the correct level, and then install
the oil filler cap.
4. Install the oil check bolt, and then
tighten it to the specified torque.
To change the transmission oil
1. Place an oil pan under the trans-
mission oil case to collect the used
oil.
2. Remove the drain bolt and the oil
check bolt to drain the oil.
3. Install the drain bolt and the
check bolt, and then tighten them to
the specified torque.4. Remove the oil filler cap, add the
specified amount of the recom-
mended transmission oil, and
then install and tighten the oil
filler cap.
ECAM1020
CAUTION
Make sure that no foreign material
enters the transmission case.
5. Start the engine and let it idle for
several minutes while checking
the transmission oil case for oil
leakage. If oil is leaking, imme-
diately turn the engine off and
check for the cause.
Recommended transmission oil:
See page 8-1.
Oil change quantity:
0,75 L (0,65 imp.qt)
Tightening torque:
Transmission oil drain bolt:
17 Nm (1,7 m•kgf)
Oil check bolt:
3 Nm (0,3 m•kgf)
Tightening torque:
Oil check bolt:
3 Nm (0,3 m•kgf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 39

comes on just before braking takes
effect. If necessary, adjust the brake
light switch as follows.
Turn the adjusting nut while holding
the rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a).
To make the brake light come on later,
turn the adjusting nut in direction (b).
EAU22420
Front brake pads
Each front brake pad is provided with
a wear indicator groove, which allows
you to check the brake pad wear wit-
hout having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that thewear indicator groove has almost
disappeared, have a Yamaha dealer
replace the brake pads as a set.
EAU22480
Rear brake pads
Each rear brake pad is provided with
a wear indicator groove, which allows
you to check the brake pad wear wit-
hout having to disassemble the brake.
Check the brake pad wear as follows.
1. Remove the brake caliper bolt,
and then tilt the caliper forward to
inspect the wear indicator groo-
ve. If a brake pad has worn to the
point that the wear indicator gro-
ove has almost disappeared,
have a Yamaha dealer replace
the brake pads as a set.2. Install the brake caliper bolt, and
then tighten it to the specified
torque.
EAU22610
Checking the brake fluid
level
Insufficient brake fluid may allow air
to enter the brake system, possibly
causing it to become ineffective.
Tightening torque:
Brake caliper bolt:
30 Nm (3,0 m•kgf)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-14
FRONT
mín.
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 46

EAU22760
Drive chain slack
(a) Drive chain slack
The drive chain slack should be chec-
ked before each ride and adjusted if
necessary.
EAU22771
To check the drive chain slack
1. Place the motorcycle on the
sidestand.
NOTE:
When checking and adjusting the dri-
ve chain slack, there should be no
weight on the motorcycle.
2. Shift the transmission into the
neutral position.
3. Move the rear wheel by pushing
the motorcycle to locate the tigh-
test portion of the drive chain,and then measure the drive chain
slack as shown.
4. If the drive chain slack is inco-
rrect, adjust it as follows.
EAU22920
To adjust the drive chain slack
1. Cotter pin
2. Axle nut
3. Lock nut
4. Chain tensioner
1. Remove the cotter pin from the axle
nut, and then loosen the axle nut.
2. Loosen the chain puller locknut
at each end of the swingarm.
3. To tighten the drive chain, turn
the adjusting nut at each end of
the swingarm in direction (a). To
loosen the drive chain, turn theadjusting nut at each end of the
swingarm in direction (b), and
then push the rear wheel forward.
NOTE:
Using the alignment marks on each
side of the swingarm, make sure that
both adjusting nuts are in the same
position for proper wheel alignment.
ECA10570
CAUTION
Improper drive chain slack will
overload the engine as well as
other vital parts of the motorcycle
and can lead to chain slippage or
breakage. To prevent this from
occurring, keep the drive chain
slack within the specified limits.
4. Tighten the locknuts, and then
tighten the axle nut to the speci-
fied torque.
5. Insert a new cotter pin into the
axle nut, and then bend its ends
as shown.
Tightening torque:
Axle nut:
90 Nm (9,0 m•kgf)
Drive chain slack:
40~50 mm (1,5 ~1,9 in)
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-16

a
a
b
2
1
4
3
5WX-F8199-E1.qxd 14/12/2004 15:05 Página 48