2003 YAMAHA TW200 clock

3-1
LOCKOFFON
EAU00029
Main switch/Steering lock
The main switch controls the igni-
tion and lighting systems. Its oper-
ation is described below.
EAU00032
ON:
All electrical circuits are switched
on, and the headlight, meter light,
taillight and front position lights
come on. The engine can be start-
ed. The key cannot be removed in
this position.
EAU00038
OFF:
All electrical circuits are switched
off. The key can be removed in this
position.
EAU00042
LOCK:
The steering is locked in this posi-
tion and all electrical circuits are
switched off.
The key can be removed in this
position.
To lock the steering, turn the han-
dlebars all the way to the left. With
the key at “OFF”, push it into the
main switch and release it, turn it
counterclockwise to “LOCK” and
remove it.
To release the lock, turn the key to
“OFF”.
EW000016
w
Never turn the key to “OFF” or
“LOCK” when the motorcycle is
moving. The electrical circuits will
be switched off which may result
in loss of control or an accident. Be
sure the motorcycle is stopped
before turning the key to “OFF” or
“LOCK”.
EAU00027
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 11

3-5
INSTRUMENT AND CONTROL FUNCTIONS
1
2
3
4
5
6
7
8
9
1
2
EAU00158Front brake lever
The front brake lever is located on
the right handlebar. Pull it toward
the handlebar to apply the front
brake.
1. Unlock
2. Open
EAU00162Rear brake pedal
The rear brake pedal is on the right
side of the motorcycle. Press down
on the brake pedal to apply the
rear brake.
EAU00177
Fuel tank cap
TO OPEN:
Insert the key and turn it 1/4 turn
counterclockwise. Turn the cap 1/3
turn counterclockwise and remove
it from the tank.
TO CLOSE:
Put the cap in the filler neck and
turn it 1/3 turn clockwise. Lock the
cap by turning the key 1/4 turn
clockwise, and remove the key.
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 15

6-30
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
1
3. Remove the connector and the
bulb holder cover.
4. Turn the bulb holder counter-
clockwise to remove it and
remove the defective bulb.
EW000119
w
Keep flammable products and your
hands away from a bulb while it is
on, as it is hot. Do not touch a bulb
until it cools down.
5. Put a new bulb into position
and secure it in place with the
bulb holder.
1. Bulb holder cover
EAU01191
Headlight bulb replacement
This motorcycle is equipped with a
quartz bulb headlight. If the head-
light bulb burns out, replace it as
follows:
1. Remove cowling A. (See page
6-6 for cowling removal and
installation procedures.)
2. Remove the headlight unit.
1
EC000105
cC
Avoid touching the glass part of a
bulb. Keep it free from oil; other-
wise, the transparency of the
glass, life of the bulb, and lumi-
nous flux will be adversely affect-
ed. If oil gets on a bulb, thoroughly
clean it with a cloth moistened
with alcohol or lacquer thinner.
6. Install the bulb holder cover,
connector and headlight unit.
7. Install the cowling.
8. If the headlight beam adjust-
ment is necessary, ask a
Yamaha dealer to make that
adjustment.
1. Bulb holder
5FY-9-E0 (TW200) 7/29/02 10:54 AM Page 59